Having problems with your Oreck XL Ultra Bagged Upright Vacuum ?

My oreck XL motor runs slow or not at all

\015 I removed the bottom plate and switched it on while it was upside down on a table. The motor ran for a few seconds and then started sparking under the plastic guard. Does this mean new motor time?\015

Answers :

Repair Help & Product Troubleshooting for Oreck XL Ultra Bagged Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My oreck XL motor runs slow or not at all


... Oreck XL Ultra Bagged Upright Vacuum

Hello, I have a problem with my Eureka Powerline bagged upright vacuum. It has a 12 amp motor and is model #4352, Type D. It was probably bought new in 1998. My problem is, while vacuuming today the motor seemed to slow down all of the sudden and then began smelling like burning rubber. I shut the vacuum off to check for blockages but could not find anything blocked. When I then turned it on again it runs but seems to only be running at 1/2 the motor speed and still has the rubber buring smell.


It sounds like a rubber sealing in the motor has come loose and is being constantly rubbed against the walls of the motor with would cause the smell and loss of motor speed caused by the fricton of rubber against the rod so if you can get to the moto ... Vacuums

The Oreck vacuum motor sparks the stop running. Plugged to another outlet, the motor did the same things, run for few seconds with sparks and stopped again.


... Oreck XL2200 Bagged Upright Vacuum

I have an older Oreck XL vacuum that sounds like it is running twice as fast as it should. I disassembled the entire vacuum, including disconnecting the motor wires, to clean out the hair, string, and other things. When I put everything back and connected all the wires, everything appears to work, including the light. The only problem is, it sounds extremely loud like the motor is running too fast. The model number is: XL3610HH Ser. No. 3610HHXA039740-6 I do not have as electrical diagram to see


... Oreck XL Ultra Bagged Upright Vacuum

I replaced the motor in my Oreck vacuum and it runs much faster than it used to and is very noisy. The wiring diagram that I received with the motor was very hard to read so I don't know if I wired it correctly. I also was not able to hook up the dual head lamps. Thanks, Bob


Hello Bbrote,Please visit the link provided below and find your model and then click for schematic :http://www.hescoinc.com/vacuum_cleaner_parts/oreck.html ... Vacuums

The motor runs slow (so does not pick up properly) and does not run at all if the hose is pulled out. There doesn't seem to be a blockage and the roller is clean. Could it be as simple as changing the filters?


... Sebo Felix Ice Blue Bagged Upright Vacuum

Oreck XL2200: It turns on, the motor is running, the belt is on properly, but the roller brush is not moving


Quite often this is caused by either a broken or stretched belt, does not seem to be the problem here, or a frozen beater brush, the brush the belt drives.\015\012Remove the beater brush and clean as best you can. Spray a little WD40 between the bru ... Oreck XL2200 Bagged Upright Vacuum

Have a baby lock blind hemmer bl101, the needle moves slow, at times will stop. But the motor is still running. Whay could be causing this?


... Vacuums

Kirby heritage 2 motor runs slow then speeds up with burning smell.


Replace your belt and clean your roller brush. ... Kirby Vacuums

The DC04 Zorbster runs slow, it still picks up but I am worried it will overheat. If I hit it at the front, the motor picks up speed until the next time I start it up. Can you help???


The problem is likely caused by either (a) a broken or worn microswitch operating lever or (b) a faultyt microswitch. With the bin removed, the lever becomes visible just above the filter upon which the base of the bin normally rests.Repl ... Dyson DC14 Bagless Upright Cyclonic Vacuum

My Optima Eureka model 431BX suddenly slows down motor still running while vacuuming and after a minute speeds up again. Everything is clean and no obstructions. .??


... Vacuums

Oreck xl9100 runs okay when upright but when the handle is at an angle the motor stops


You must test the power cord for open or break use the VOM2) Test for main switch some wires loose, or bad solder, or switch defective, and replace.3) Thermal fuse, loose, or bad contact. tight.4) See if the belt is sliping or broke or wo ... Vacuums

Stopped running My mother's Oreck vacuum sound as if there was something bogging the rotating brush down. I pulled the bottom cover off and found nothing wrapped around or restricting the brush. I tried to finish vacuuming with the problem then I turned it off to move a chair and turned it back on it would do nothing. Any suggestions as to what could be causing the vacuum to sound as if the rotating brush is being restricted from turning. There was not odor of burning as if the motor was in a bi


Orecks have a plastic fan inside and everything you pick up hits it, sometimes things can get stuck in there or break the fan locking up the motor. With the machine off, poke around where the dirt goes into the motor, behind the roller and see if you ... Oreck XL Ultra Bagged Upright Vacuum

My Oreck XL is very dirty inside on fan and the motor runs very loud. It is not clogged.


These units are called dirty air units because the dirt literraly runs thru the fan attached to the motor and is blown into the bag. Most newer vacuums are called clean air because the filter bag is in the path, and the dirt is sucked into the bag, n ... Oreck XL21 Bagged Upright Vacuum

My Oreck XL is spitting dust out of the housing when it runs. There is a crack in the plastic intake that connects to the motor. Can this be fixed or replaced?


I have a model XL2450RH and it has been blowing dust out of the joint in the back is this the same issue??? ... Oreck XL Ultra Bagged Upright Vacuum

I accidentally ran over the cord and then machine motor slowed down and stopped running. It wouldn't turn back on


Get a new cord. It was stretched and ripped apart under the outer rubber cords housing insulation ... Kirby G4 Bagged Upright Vacuum

Fantom vpw46h,house pressure washer.the motor runs,it was setting for sometime started,using it,but never had any pressure besides the house hose pressure, with the motor running,then the pressure startes to work great,while using it the wand hose came out of the pressure washer,i put it back in,now the motor will only run when i try to adjust the wand head but will not produce any pressure and will shut the motor off,it seem like as soon as the wand hose came out of the presure washer and after


... Vacuums

Kenmore canister model 116.25513506 wont turn on. when handle switch is turned to floor. vac motor does not turn on. When switch is turned to carpet, floor nozzle works but vac motor does not. I checked fuse, all o.k. checked continuity for plug, o.k. removed wires for bag full switch...motor wont run. I wired motor directly power cord...motor runs. Thinking it must be the circuit board, how do I bypass it or test it?


... Vacuums

I had a loose wire in my Oreck XL motor. I took it


Lights are 12 volts.\015\012\015\012The motor has taps on it to pull 12 volts rather than 120 volts for the lights, uses the motor as a transformer.\015\012\015\012Should be black and white to the motor from the switch, believ ... Oreck XL Ultra Bagged Upright Vacuum

Model # 5770 the brush motor runs and shuts down after a few seconds...Turn unit off and the brush again will run for a second or two...If I don't turn unit off brush will not start up..Could it be the printed board..the motor brushes..or the wiring that goes from the printed board to the main motor...Thank you


Seems like your unit goes into failsafe because it detects something wrong. Well you should check the brushes and replace them if they are worn out. Also check the wiring for shorts etc, becaue the unit maybe tripping due to an overload. The printed ... Bissell Vacuums

Kenmore Progressive canister model 116.27514700 Problem: Vacuum motor won't turn on. The power head operates, but nothing from the vacuum. Have checked all areas of airflow: hose, bag, motor filter and hepa filter. All are fine. Have checked and rechecked all electrical connections, all seem to be in working order. Vacuum hasn't run for a week or so, so it's not the thermal protector, unless it's defective. Vacuum was running fine last week. Didn't stop operating when using. Went to v


Hello! The culprit is the PCB Assembly; Part # KC86WBZR3000...Cost is $6.99. I would remove and inspect for burnt components, or broken wires...Then clean connections both male/female using an eraser, toothbrush and alcohol...Using a bright ... Vacuums

DT 1300 As I am vacuuming the motor seems to fade in and out and sometimes stops running for a few seconds and then resumes. If I move the hose a bit near the vacuum end, it runs smoothly again. Does this sounds as if there might be a short in the motor? Would this be something I can fix myself or does the vacuum need to go in for repairs.


... Oreck DutchTech DTX1300C with Motorized Carpet Brush Bagged Canister Vacuum

I have a mile tt2000 that works fine up to 1300W but if I crank it up higher the motor decreases and increases speed every couple of seconds. I have changed the bag and filters and done the usual cheCks for blockages but can find nothing amiss. Unusually when it is running and I block the intake it will run at full power but as soon as I clear it the motor "hunts" again. Any ideas.


... Miele Cat & Dog 326i Bagged Canister Vacuum

Does not pick up, no vaccum, motor runs, no blockage, should feel suction on hose outlet without hose hook up. Paper filter missing over cloth filter. float overload ball free, seal on section good no leakage. Maybe bad motor but runs.


Here\015\012 is a Link to one of my Tips:www.fixya.com/support/r6311178-vacuum_brush_bar_not_spinningThis\015\012 should solve the problem. ... Minuteman C82906-01 HEPA Vacuum Vacuum

I have Nutone VX550C. Motor runs intermittently (cycles on and off rapidly--the light on the handle is blinking furiously) when I use the on/off switch on the hose. This happens at all of the wall connectors, so suggests a hose contact problem. Motor runs continuously when I turn it on at the switch on the wall unit.


The unit does have a switchs the PVC outlets, and it sounds like the hose mech to operate the switches is broken, and intermittently making contact. A replacement hose would likely fix the problem. Looked them up on the net, and they're not che ... Broan-NuTone VX550 Bagged Central System Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0339 seconds