Having problems with your Oreck XL Ultra Bagged Upright Vacuum ?

Oreck XL Is there any chance you could e-mail me the wiring diagram for the Oreck XL? I just can't read the one that's on-line. Thanks, [email protected]


Answers :

I would advise you to ALWAYS to FIRST UNPLUG THEIR VACUUM before beginning any service procedure. The motor has 5 wires to the motor as stated in the Oreck owners manual, tow are for the headlights, one is a ground wire, and the other two are for the motor. There are two screws that hold in the Oreck motor and a good suggestion is to use tape the wires leads and mark the wires so that you will not make a mistake as you take it apart and reassemble the motor. That way you will not make any mistakes, whether or not you have wires for a headlight or not, the rules are the same. Also refer to the owner’s manual schematic and the exploded view. Questions? 1-800-989-3535
\015\012www.Oreck.com
Repair Help & Product Troubleshooting for Oreck XL Ultra Bagged Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Oreck XL Is there any chance you could e-mail me the wiring diagram for the Oreck XL? I just can't read the one that's on-line. Thanks, [email protected]


I would advise you to ALWAYS to FIRST UNPLUG THEIR VACUUM before beginning any service procedure. The motor has 5 wires to the motor as stated in the Oreck owners manual, tow are for the headlights, one is a ground wire, and the other two are f ... Oreck XL Ultra Bagged Upright Vacuum

Oreck XL3610HH I would like to receive the wiring schematic via email attachement so that i might be able to read it. The one posted is great but i cannot get any detail from it. Thanks so much! [email protected] Lee


... Vacuums

Hi, can you email me the version of a XL Oreck wiring diagram. The one on line is too small to see


1. Try zooming in on the online diagram.\015\0122. Copy and paste into a paint shop type program, then enlarge it. ... Vacuums

I Need a Wire Diagram for my Oreck XL3600HH!!!


Can u coward it to me. [email protected] my orek started smoking by the engine white smoke. smells like a electrical prob. I'm trying to fix it myself. I'm not sure what's wrong with it. belt is Ok. no clogs. belt didn't move and bag isn't in ... Vacuums

Can the two inlet pipes be connected to one line? The central vacuum I have is probably from 1993/4. It has one exhaust pipe and two inlet pipes. It was initially under my stairs. I would like to move it and have in fact moved it to the garage but am now fitting the pipes. I would like to join the two pipes that were previously going to the two inlets into one pipe. Can I do it? Also would I then join the wires? Would I put a plate on the other inlet? THANKS. It is a SMART president's choice vac


There is no real reason why not...As long as you have enough "****" then that should be fine, you will need to "Y" join and NOT a "****" joint. ... Vacuums

I replaced the motor in my Oreck vacuum and it runs much faster than it used to and is very noisy. The wiring diagram that I received with the motor was very hard to read so I don't know if I wired it correctly. I also was not able to hook up the dual head lamps. Thanks, Bob


Hello Bbrote,Please visit the link provided below and find your model and then click for schematic :http://www.hescoinc.com/vacuum_cleaner_parts/oreck.html ... Vacuums

Hi, I appreciate your wiring diagram for the Oreck XL motor --but it is too small to read. Could you send me a readable copy. Thanks very much for your help! Nels Klyver


Print out the diagram u have, then scan it and blow it up to a larger size (all scanner allow u to enlarge the image), this is what I do with hard to read electrical diagrams. ... Vacuums

Oreck wiring I've read the threads. Which 2 terminals are the lights and which 2 are the motor ac?


... Oreck XL21 Bagged Upright Vacuum

I have bought a second hand necchi blind hemmer machine looks very good but the stitches are not looping so cant turn a hem on it thats why i would like to read book belonging to same to see if i doing something wrong


... Vacuums

Over heats and shuts off, wont start again untill it cools off. can maybe vacuum one room before overheating. cyclone tubes are all clean, all hoses & lines are clear. this vacuum is fairly new, not used much. cant find a reset button. is the moter dirty of something?


The electric motor has a thermal switch and is self-resetting so there is no re-set switch. Make sure the air filter for the exhaust is clean. Also make sure that the height adjustment is not too low causing strain on the motor. Always bring the heig ... Dirt Devil Reaction Twin Cyclone Upright Vacuum

Oreck Upright Hi Redev, I'm not sure what model I have (about 6 years old...upright, looks like the one in the picture). I changed the belt (which was torn) and then the next time I used it, it cut off on me. Now if won't turn on at all. (I turn the switch on and off and nothing happens as if it is not plugged in but it is!). I noticed at the top where the power cord enters the handle, it is all frayed. Could the electrical wires have detached? Anything you think I should check before taking it


The cord could be bad and will ahve to be replaced. It would have to have a problem inside the handle or down by the motor. ... Oreck XL2600 Vacuum

Trying to wire aa Nutone model 763RL bath exhaust fan/light. The conduit coming from the breaker box has a red wire, a black wire, a white wire and a ground. The fan has two white wires, one black wire, one blue wire and one green wire. I have wired the whites together, but do not know how to wire the blance.


... Vacuums

Hello, I am looking for a wiring diagram to install a touch/dimmer switch by "Comfort" mdl # RH-934B - Darjung Ind Ltd. It has a standard lampcord (two wires) coming from it as well as one white, one black and one yellow wire. The original touch/dimmer switch (no identification on it) had one white, one black, one red and one yellow - no lampcord. Thank you very much for your help!


The black and the white will go to the lamp ,eg,output.The yellow is the sensor wire which should be firmly attached to the metal base of the lamp ... Vacuums

Explain how to re-wire 16gal craftsman shopvac,switch wires are- 2 orange wires, one white, one black and one green(grd wire), I pulled them off and don't where each wire goes.


Im not looking at a diagram of your machine.\015\012\015\012Typically, in a switch circuit ... the green goes through; the white goes through; the black is broken by the switch.\015\012\015\012The two orange wires you speak of ... Vacuums

Confusion and embarrasement have caused me to appeal for expert advice. I need to add a second flourescent light fitting in the loft. I recently added one from the existing wiring circuit via junction box and pull chord switch and it works fine. I have wired in the second light and now neither of them work. I have replaced the starter (as I had a faulty one in the first light. But i annot get them to work. I have installed a second junction box for the second light and wired all like terminals


... Vacuums

I'm a bit confused. I just purchased the Spot Bot Pet and am trying to figure out how to fill the tank. I see where the lines are for set in stains but it isn't clear to me why there are 3 lines, one for water, one for "OxyGen2" and one for "Formula".Please explain


... Bissell 1200A SpotBot Pet Robotic Vacuum

Nutone Broan CV556 runs continuously and will not shut off until I unplug it.. I disconnected the low voltage wires and it still runs when I plug it in. Inside the top of the vacuum are 3 electrical devices - one looks like a transformer wire -- one is a rectangular electronic black box. The third is an on off rocker switch. Which piece it likely to be shorted out? It is about 8 years old.


... Broan-NuTone CV556 Cyclonic Bagless Central System Vacuum

My Oreck XL 9100HA started smoking (white smoke) when I vacuumed. There is a burning rubber smell. How do I check/change (if appropriate) the belt? I have no User manual, nor can I locate one on the Oreck site. The bag is a new one. The vaccuum had been picking up, though not at its best strength.


It sounds like the belt has been damaged. You can get another belt from yoru local Oreck store. You can even take it in to the store to show them what happened. Purchase another belt and replace it. (It was very easy when I did this, so hopefully ... Oreck XL Ultra Bagged Upright Vacuum

I am trying to change an old fashioned fuse, (house lights), luckily had a spare one. Have put the 15amp fuse wire through the whole thing, and trying to describe if I've got it right is alitle awkward, this is what i've done, cut a piece of 15amp wire a little longer than the old one, then loking at it, taken it straight through and round to left as I'm looking at it, and put the screw in, and obviously done the same for other side. My problem is that I don't remember taking the screws out of w


Hi.your descriptions are understandable and sound about right.as long as the wire is securely fixed to both pins, you should be ok.if there are any problems, especially if the fuse blows again fairly soon, then i strongly reco ... Vacuums

I have bagless samsung air track 2000w tein cleaner vaccume cleaner..it has only one switch for on and off...cant find a switch to put the cord back????? .


... Vacuums

Wiring diagram took wires off motor and do not know which goes where.There are two main from plug in one whit one black then two of same coming from light in front.On the motor ther are more terminals than wires.On diagonal corners there are black dots.Can you please help this cost 800$ and do not want to burn the motor due to crossing pos and neg.Do you have a picture or know where I can find?


... Oreck XL21 Bagged Upright Vacuum

Wiring schematic oreck xl2600hh


I have a Oreck XL and the propeller that is in the housing will become hard for the moter to turn. I have took it apart and do not see a problem, but when I reinstall the parts it will run for about 15 sec. and the moter will stop turning. When the ... Oreck XL Ultra Bagged Upright Vacuum

Wiring diagram for Model #11635922500 - KENMORE Upright vac I took the cover off of the vacuum to repair the power cord and must have pulled a wire out of its wire nut by the sweeper bar. If I had a diagram it would be no problem to replace. The bad has four short gray wires coming out of it. It is one of the gray wires that has come loose.


... Kenmore Vacuums

Local vacuum repair shop replaced motor in Oreck XL 2600HH and now the lights blow out immediately upon powering up the machine. I believe the wires for the lights were mis-wired to the terminal blades on the motor housing. is there a wiring diagram available to properly connect the wires to the motor housing?


Hello. if this repair just occurred return this vacuum to that repair shop as they owe you a valid repair. I agree that they caused the lights blowing out problem. They must repair this for no charge. If you work on it yourself they will blame yo ... Oreck XL2600 Vacuum

Hello, I,ve just bought an Italian designed 3 bulb 70's wall lamp. It has a 2 wire lead feeding out with 2 wire lead running from one bulb socket To the other 2 inside the casing. I'm trying to wire it in my porch which has 3 wire cable coming from a 13amp plug for power. Any suggestions on making this work please ?


... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0397 seconds