Having problems with your Oreck XL Ultra Bagged Upright Vacuum ?

Wiring Schematices Hello, Thank you for posting the wiring schematics on FixYa. Those are the ones I needed. However, I cannot make them out on the webpage. So, if you could kindly send me a copy to my e-mail address, it would b highly appreciated. Prefferably in .pdf format if possible. Thank you very much. Desperate To Repair Kent

Answers :

I had the same problem after not paying attention to the connections when replacing my motor. I spent days searching for information and only found several non-answers with small photos that no one can read.I contacted Oreck for wiring information. They explicitly stated that they can't provide any wiring information for safety and liability reasons.

I found the Ametek schematic which shows the LINE and TAP locations on the motor.

Note: I have a 2600HH XL with 2 headlights.

Connect as follows:

3A, LINE: White lead w/piggy back terminal from light harness #1 & white lead from the power harness to the piggy back terminal
2A, TAP: Black lead from light harness #1
3B, LINE: White lead w/piggy back terminal from light harness #2 & black lead from the power harness
2B, TAP: Black lead from light harness #2
\015\012Wiring Schematics (by 2 users)
\015\012Posted by KentDW62 on Mar 31, 2008
\015\012Hello, Thank you for posting the wiring schematics on FixYa. Those are the ones I needed. However, I cannot make them out on the webpage. So, if you could kindly send me a copy to my e-mail address, it would b highly appreciated. Preferably in .PDF format if possible. Thank you very much.
Desperate To Repair …..Kent


\015\012This Problem has been added to the Share Your Expertise Page under "My Work Queue".
\015\0121 Other User Has the Same Problem\015\012Comment by Rick Palmer, posted on Apr 04, 2008. I need to get a wiring diagram for an Oreck XL2, any help would be greatly appreciated\015\012 \015\012Hello,
I would advise you to ALWAYS to FIRST UNPLUG YOUR VACUUM before beginning any service procedure. Oreck XL Ultra Bagged Upright Vacuum. The best place to get an owner’s manual is from the Oreck Factory of which I will supply for you listed below or you can download the owner’s manual from the Oreck Website. . I would check with your local Oreck dealer or vacuum dealer in your area to see what is going on. This is most unusual for this to happen. So if you need further assistance, please feel free to contact your local vacuum cleaner dealer in your area or in the yellow pages, or contact the factory phone number or website to further assist you with your questions.

\015\012http://www.oreck.com/ Customer Service 1-800-989-3535
\015\012Monday thru Friday Hours are: 7:00 am to 7:00 pm CST
\015\012Saturday and Sunday Hours Are; 8:00 am to 4:30 pm CST
\015\012http://www.a-1vacuum.com/ 1-800-657-1874 Customer Service
\015\012Thanks, Don the Vac Man
Go Ahead. Use Us.

Repair Help & Product Troubleshooting for Oreck XL Ultra Bagged Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Wiring Schematices Hello, Thank you for posting the wiring schematics on FixYa. Those are the ones I needed. However, I cannot make them out on the webpage. So, if you could kindly send me a copy to my e-mail address, it would b highly appreciated. Prefferably in .pdf format if possible. Thank you very much. Desperate To Repair Kent

I had the same problem after not paying attention to the connections when replacing my motor. I spent days searching for information and only found several non-answers with small photos that no one can read.I contacted Oreck for wiring information. T ... Oreck XL Ultra Bagged Upright Vacuum

Product instructions need full view of internal schmatic and instructions on how to change belts or troubleshoot problems. I have the 1699 proheat and the 7901 Bissell I would appreciate a copy of operating instructions. Thank you, Raja Burns email address [email protected]

You can change the belts from the bottom, remove the brush roll, then you can reach thru slot to change the pump belt, then the cogged belt. Wasn't sure which darwing you wanted, if it is electrical, let me know.\015\012\015\012 ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

I just bought a Danby Premiere air conditioner #317826. I need a newset of tubing, as it is messed up. I would really appreciate it, my name & address is Sammie Visage, Rt 1 box 171, Carter, OK 73627. When I visited my sister in TN, she showed me hers and I was impressed, so bought one. I live in Western OK in a town of 300, A Lowes store is 2 1/2 hours from us. So you can see why I would really appreciate your help. Thank you, Sammie Visage

... Vacuums

HI THERE!!! I've noticed that you have been helping me with answering questions about Kirby vacuums with my links to my guides for quite a while now. I'd like to thank you for this, but I'd like to request that you use the direct links to my guides instead of copying from them and pasting it into the answer box. If you use the links, it will help me A LOT and I would GREATLY appreciate it. Thank you again for all of your help!!!! Marci (b0sslady2001)

Http://www.geeksquad.fixya.com/ThreadView.aspx?prdid=11557&thid=534650\015\012HI THERE!!!\015\012Posted by b0sslady2001 on Apr 21, 2008\015\012I've noticed that you have been ... Kirby Ultimate G Bagged Upright Vacuum

I have a Hoover SteamVac SpinScrub with Clean Surge Carpet Cleaner. I loaned the cleaner to my son, who lives 3 hours away from me. My son returned the Steam Cleaner to me on Easter Sunday. My son failed to return the Owner's Manual. I need to clean my ottoman. I have never used the upholstery & stair cleaning tool. Would you be able to e-mail me the instructions for this chore? My e-mail address is: [email protected] My name is Kay. Thank you!

Hi,I would be glad to send that. But, you never Mention the Model Number and there are Various Models introduced by Hoover.Let me know the Manual and within Few Minutes, i would be able to send you one more email which would h ... Vacuums

I am looking for an instruction manual for the Pinnock1 Overlocker. Is it available on line, if so I would appreciate assistance in obtaining a copy Thanks Michael

Hello\015\012Visit this site. You can either buy or download it free the manual of sewing machines you need.\015\012\015\012sewingonline.co.uk/instructions/newhomelock777/\015\012 ... Vacuums

Hi. I can get my FunLock 007D serger threaded fine (as it's color coded) until I get down to the area that includes threading the needle. Can you give me some instructions that will guide me through this? I have the manual that came with the machine, but the illustration isn't clear or specific enough for me to follow. I'd sure appreciate some assistance on this. My e-mail address is: [email protected] Thanks you. Vicki Flagg

More specifically, what are having problems with when it comes to threading the needle? ... Vacuums

Hi, I appreciate your wiring diagram for the Oreck XL motor --but it is too small to read. Could you send me a readable copy. Thanks very much for your help! Nels Klyver

Print out the diagram u have, then scan it and blow it up to a larger size (all scanner allow u to enlarge the image), this is what I do with hard to read electrical diagrams. ... Vacuums

Dc15 fuse The roller brushes on my dc15 stopped working..I checked the obvious and then noticed that the 2 amp fuse was blown on the circuit board . I've replaced it with the same type bought from Maplins but it keeps blowing .. I tested the yellow an blue wires leading from the circuit board to the roller brush head and the are in tact and I can run a current through them ... Any thoughts from anyone .? Your help would be. Appreciated thanks Lee

Hi Lee,I'm sorry to hear you're having difficulty with your DC15. If you'd like some help, please give us a call on 0800 298 0298 - we may be able to resolve the issue with some troubleshooting over the phone.Best wishes,Jack ... Dyson DC15 All Floors - The Ball Bagless Upright Cyclonic Vacuum

I am trying to find a replacement water tank cap for a Vicks V4450 humidifier. I dropped the cap and broke it on the edge. Everything I see on line does not say it will fit the V4450. My e-mail address is [email protected] My name is Andy. I would like the part number to order and price and web site to go to for the ordering process. thank you Andy

Http://pg.custhelp.com/app/ask This is a link for Vicks online help section. I'd shoot them an email and simply ask if they can send or sell you a new one. Have the model n ... Vacuums

I purchased a utilitech 7-day digital in-wall timer #0141224. My house wires are two black wires and a green ground wire. The new timer has a w,g, r, and b, wires. My question is what wires do I connect. I found the black power wire from the house. I have no white wire in the switch box. Where would the red wire go? Thank you

Hi!!\015\012\015\012\015\012\015\012The Green wire goes to ground, \015\012The White wire is the neutral. (in this case is used to supply power to the clock.) ... Vacuums

Hi, I have an old 2 wire chandelier I would like to make a plug-in. I have bought the wire swag kit to change it, but the chandelier wires are unmarked. Both wires are copper and I cannot see an insulator on either side...I need help!! Thanks!

Can you determine some way of telling which wire goes to the center conductor on each of the lamp sockets. (That particular wire,-- however it is identified-- (Maybe a tracer thread? in the woven ins ... Vacuums

Can the two inlet pipes be connected to one line? The central vacuum I have is probably from 1993/4. It has one exhaust pipe and two inlet pipes. It was initially under my stairs. I would like to move it and have in fact moved it to the garage but am now fitting the pipes. I would like to join the two pipes that were previously going to the two inlets into one pipe. Can I do it? Also would I then join the wires? Would I put a plate on the other inlet? THANKS. It is a SMART president's choice vac

There is no real reason why not...As long as you have enough "****" then that should be fine, you will need to "Y" join and NOT a "****" joint. ... Vacuums

The Bissell Proheat 2X doesn't release the solution. I have cleaned everything I can see and understand there is a filter somewhere. Would like to know if that would even help... ANY OTHER SUGGESTIONS WOULD BE APPRECIATED! No men around just us girls and we have NO idea how to fix it!! Thanks-Cheri

Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

A 'burn' hole has appeared in the Microwave Outlet Cover causing arcing (or similar sparking and blue flashing!). Would replacing this cover with a new one solve the problem or does it suggest something that would quickly reoccur? Would it be an economical repair or should we ditch the machine for a replacement? Thanks in advance etc it is appreciated.

... Vacuums

I got a vacumn from a friend who ungraded and though i used at her home when i got it home it would not turn on when plugged in and i check everything and no use. my friend lost her manual. im in my 60's and on a disability fixed income so cant afford to take to repair but got lots of men at church who would help if they know how to trouble shoot it. and would really appreciate any help. thank you , ann

Hi\015\012In the UK we have similar machines but they are made by Vax. If you can't source the correct user manual from Hoover.com consider the following - it is a free download.\015\012\015\012http://www.vax.co.uk/downloads/pdf/vzl-60156016_v2 ... Hoover U5194-900 Mach5 Multi-Chamber Cyclonic Vacuum Cleaner Bagless Vacuum

Would it be possible to get a Viking 714 sewing machine manual? I just inherited the machine and would like to use it, but it came without the manual. Thank you! Your help in this is much appreciated! A.S.

... Vacuums

My plunger (bought in Chile) has 1. a metal filter, 2. a convex (not flat) metal disc with central hole for rod, 3.a metal disc with holes of two different sizes in circles radiating from the centre 4. plunger rod with screw and 5. a spirally coiled wire forming a circle. I cannot figure how to fit these especially the coiled wire. Help appreciated. Thanks

Place the coil in the hole and turn untill reach the desired height. ... Vacuums

My Bernina 807 set on min. speed takes off fast, doesn't go slow at all, although there is a difference in the slow speed setting and high speed setting if I switch from one to the other while stitching. The machine is well oiled and goes well apart from this. I would like min. speed to start smoothly and slowly. I have read it could be capacitor in foot, but DH says it does not look burnt out. Would it help my problem to remove it? thank you, Barbara

... Vacuums

Hi, I have been given a beautiful Husqvarna Prisma 980 and the power seems to have stopped getting to the machine.. The first time I plugged it in it worked, all the lights came up where they are supposed to, then the second time nothing =( Some help would be appreciated as I would like to fix it instead of throwing it in the bin Thanks Vicky

If you're really serious about getting this machine running, you need a service manual. Here is a .pdf download manual:\015\012 ... Vacuums

My sister misplaced the instruction manual to her emerson microwave and I would like to replace the instruction manual. I do not have the model number available and only know she bought it at Walmart for around $60. I would appreciate any help. Thank you.

Hi,\015\012\015\012Since you do not have the model number of the Microwave, kindly view and identify the model from the complete list on the Emerson website by clicking this ... Emerson Vacuums

I recently made a long distance move and the charging wire for my Electrolux Pronto 2 in 1 didn't make it to my new home. How do I get a new one? Thank you. Your promptness of reply will be greatly appreciated as I miss this very handy gadget. Thank you, Marie

Hi,You can buy it separately in the Electrolux service center if you need it urgently.Please choose the are in electrolux and choose the nearest service centre.elsebuy onlinehttp://www.bizrate.com/vacuum-ac ... Electrolux Pronto 2-In-1 Stick/Hand Vacuum - Cayenne

Wiring I am desperately searching for a wiring diagram for my Orek XL2 2 speed upright. Any help would be appreciated.

Here are the 4 different wiring for new Oreck motors.\015\012 ... Oreck XL Ultra Bagged Upright Vacuum

Our SteamVac will not release cleaner and water. Everything else appears to be okay. After last use it was rinsed out and left for two weeks at which time it would not work. I would like to obtain a repair manual to study and be able to disassemble it properly. Thanks in advance, William Ferguson E-mail: [email protected]

Click this link directly\015\012http://www.sacreativeservices.com/forum_stuff/steam_vac/\015\012\015\012 ... Vacuums

We have a hoover porta vac. that at first it would sometimes come on and sometimes not. It did completely stop coming on, so I have changed the switch and the cord but with no luck. Could you offer any suggestions or is this a motor situation. To my knowledge the motor was not making any noise. Your help would be greatly appreciated. Thank You, Molly Maid of NW Fla.

If this has had heavy use, the carbons in the motor may be worn. ... Hoover CH30000 Bagged Canister Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0510 seconds