Having problems with your Oreck XL Ultra Bagged Upright Vacuum ?

I'm trying to clear the tube on an Oreck upright and can't loosen the upper ring. Very hard to get at with the bag on.

\015 I saw the technician do it at the Oreck Vac center, but it is so tight (esp compared to the lower ring) that we can't get it to turn.\015

Answers :

If you have a large pair of pliers you can use that to loosen the upper ring.
Repair Help & Product Troubleshooting for Oreck XL Ultra Bagged Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I'm trying to clear the tube on an Oreck upright and can't loosen the upper ring. Very hard to get at with the bag on.


If you have a large pair of pliers you can use that to loosen the upper ring. ... Oreck XL Ultra Bagged Upright Vacuum

There is a clog in clear tube that sends trash from floor to cylinder. have pulled out lots but cant get really far in there. can I take the hose off somehow and get in there


Try using a hanger and see if you can snake it out there might be a small hose on bottom of power head,i hope this helps thanks ... Dyson DC18 all floors Bagless Upright Cyclonic Vacuum

I am getting very little suction from the motor. The hose is clear, the bag new. When I open the bag cover, plug the hose in and turn the vacuum on, there is next to no suction from the motor. What do you think is wrong? How do I remove the cord retractor to get to the two screws that hold the back of the canopy cover?


Your problem is probably is you don't have a proper seal in your chasis. A vacuum has to be sealed tight or the air will leak out and the seal broken. Check around the whole body after the bag is in and check for any airflow noise. I could help more ... Vacuums

My Oreck is 10+ years old. The bag will not remain on the opening of the handle inside the bag. Dust goes into the cover rather than in the bag getting in the zipper which makes it very difficult to unzip the cover. Any suggestions?


Check and make sure bag collar is behind the two lips. if it isn't it will leak dust and make it hard to open. ... Oreck XL Ultra Bagged Upright Vacuum

Telescopic wand My wife's Electrolux Oxygen has a telescoping wand that expanded and contracted. All one had to do was slide a button and the lower tube slid inside the larger upper tube. Now the button no longer moves whatever was inside to allow the expansion/contraction to happen. How do I fix this situation? The wand assembly hardly seems to be made with repairs in mind. This method of manufacturing is annoying. Thanks, Eric


... Electrolux Vacuums

I have a eureka the boss vacuum it wont pick up. I cleaned out the tubes the belt is good. the tubes are clear. What else can I do?The bag is only 1/4 full


... Eureka Vacuums

Wondering if the head is plugged up because it makes a sound like air is escaping somewhere. I've replaced the original cloth bag with a comparable "O" paper bag from Sears. I tried to see if there was a clog in the hose by placing a broom handle in the hose to see if something would loosen. I also cleaned the filter and the air filter. If the head is plugged, how can I fix it? We can't get the vacuum apart. Thanks.


I had this problem, but suction improved when the attachments were properly secured in their holders. ... Kenmore 31913 Progressive Direct Drive Bagged Upright Vacuum

Oreck has become hard to push on rugs - Oreck XL2000 Bagged Upright Vacuum


... Oreck XL2000 Bagged Upright Vacuum

Bissell powerforce My lower pickup tube became clogged so I removed it and cleaned it out and reinstalled it.Now everything runs good but the vaccum want pick up any dirt .I replaced the bag andf when I turn it on it just exhaust air but does not have any suction,I tired tp pull the bag door of while it was running whick I could not do so it has plenty of suction inside just not getting any outside can you help?


... Bissell Vacuums

I cannot keep the bag attached to the handle inside the cover on my Oreck XL Vaccuum. When it comes off dust blows out into the cover instead of the bag which makes it very hard to unzip the cover.


There should be a spring ring that slides up over the bag on the handle if thats missing try and use a couple of heavy duty rubber bands. however i do suggest you order the correct part. ... Oreck XL Ultra Bagged Upright Vacuum

We have Nilfisk Tempest 1500W bagged cleaner. It just stopped working and I have taken off top cover and all wires/contacts look OK. But power still not getting through I assume. The retractable lead goes into base and cant get to this area. How do I check main lead or perhaps you provide details of serviceman. On North Shore, Auckland, NZ.


... Vacuums

Oreck XL21 just will not work at all any more. Beater is clean - belt is fine. Fresh bag - inflates. Took the thing apart - checked for blockages at intake, bag entry, and the tube. It just doesn't vacuum anything. No suction at all for anything stronger than air. I'd say it doesn't ****, but that would be ironic. Are these known for just "quitting" after a while? We take it in for maintenance as recommended to replace filters, etc. Is there some miracle trick to make it work or sho


Did you make sure the brush turns freely? Even though it is clean, if it does not turn freely with the belt, it will not beat the carpet and pull debris up into the unit.\015\012\015\012Another (drastic?) thing to try would be to take the unit ... Vacuums

To : admiralstopf I have a U-Line clear ice maker UCLR2060B40. The authorixed service center has been trying to fix my unit since October to March. They have replaced the circuit board 2x and the Thermister and rain tube. They clai they were able to get it to work on their bench (not sure if true) but they can not get it to work in the house. They gave up and refunded my payment. Now what? Jonathan


Unfortunately we are not affiliated with any manufacturers. What I would do at this point is to contact the manufacturer of your ice maker and let them know what has transpired when you attempted to have their authorized repair center fix your issue. ... Vacuums

Oreck upright hard to push - Oreck XL2000 Bagged Upright Vacuum


If hard to push, only a few things to check:\015\012\015\012(1) Rear wheels will get hair or thread wrapped around axles, dust, etc. and be hard to turn. Make sure each wheel turns easily.\015\012\015\012(2) Small wheels on ne ... Oreck XL2000 Bagged Upright Vacuum

Cant turn the bag connect to get it off - Kirby Generation 3 Bagged Upright Vacuum


... Kirby Generation 3 Bagged Upright Vacuum

I cant get my kirby to blow out...bag is removed from seating...its plugged in...i attach the hose to the place where the bag goes, but it wont run


I did get it to work! It was a struggle, but It finally hit that hidden switch just right. The hose attaches to where the bag goes, and it just wouldnt seat properly. I suppose there might be some wear there on the hose end that twists in . ... Kirby Vacuums

Why cant I get the bag to stay on?


Sounds to me that the tube the bag connect to is broke or as got hole in it. ... Vacuums

Dust bag central tube broken - how/where can I get a new one or repair it?


Here is a video how to replace the broken tube and where to get a new one just click on top right of the video ... Kirby Heritage II Vacuum

Cant get belt on correctly - Kirby Generation 3 Bagged Upright Vacuum


Http://www.kirby.com/Portals/0/videos.html\015\012hope this helps :) \015\012if it does please vote ... Kirby Generation 3 Bagged Upright Vacuum

Need to change the motor on dc07 how do you get the motor out I have loosened and taken out all the screws and still cant disconnect the power cable in


Have you looked at www.dysonmedic.com ?\015\012\015\012It has a really good feature on changing a DC07 motor. ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Shampooer I have a rainbow e series and my shampooer is not working. The tubes do not seem to be clogged and it sounds like it is trying to work but we cant get the water to come out. We pull the trigger and nothing no soap, no water, nothing. Can anyone help?


Aqua mates have an o-ringed valve assembly that go bad regularly reccoment having it replaced by local vac shop ... Rainbow E series Canister Wet/Dry Vacuum

The black clip to hold my vacuum bag on my oreck xl signuature plus is missing..can I get a replacement one?


... Oreck Xl Signature Upright Vacuum

Broken vacuum jammed the rotating brush on a kenmore powermate vacuum cant get it to run properly after clearing the jam


Question; you can't run it properly meaning? The agitator (brush) isn't spinning? If that's the case, then Kazong is right, check the belt. If the belt is fine, check to make sure you didn't damage the bearing of the agitator.\015\012\015 ... Kenmore 23613 Progressive PowerMate Bagged Canister Vacuum

There is something stuck in it. I cant figire out how to get the tube off on the bottom I was hoping to find a manual i could download for free


You can download a manual for free here: Dyson DC17 user manual ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Cant get the suction impellar off to replace - Kirby Generation 3 Bagged Upright Vacuum


Shaft has to be spun clockwise. It has reversed thread. If this is not the problem but you just need to somehow hold the field - see instructions HERE. You may ... Kirby Generation 3 Bagged Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0883 seconds