Having problems with your Oreck XL Ultra Bagged Upright Vacuum ?

Oreck vacuum leaves brush marks on hardwood floor

\015 Oreck xl 21 upright vacuum leaves "brush" marks on hardwood floors. I have had tech at store look at 2 or 3 times, replaced the brush, cleaned the roller\015

Answers :

Repair Help & Product Troubleshooting for Oreck XL Ultra Bagged Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Oreck vacuum leaves brush marks on hardwood floor

... Oreck XL Ultra Bagged Upright Vacuum

Oreck vaccuum is leaving black marks on hardwood floor

... Oreck XL2200 Bagged Upright Vacuum

When vacuuming the floor it does not leave brush marks or pick up anything unless you reach down and lift on the very front of the machine and then it works for a while and quits again

The belt is probably worn or stretched. When this happens the belt won't turn the roller brush when it is against the carpet. Here is a link for the manual and links for the belts you need: ... Dyson DC07 Bagless Upright Cyclonic Vacuum

When vacuuming hardwood floor, hair gathers on brush and never sucks into vacuum. I spend most of my time cleaning off brushes. How do I clean hardwood floor with dog hairs.

1. Broom and dust pan, then mop\015\0122. Wet dry vac with wide non-brush attachment\015\0123. Here's a link to a vacuum professing to clean pet hairs well\015\012\015\012 ... Sebo Air Belt C2.1 Bagged Canister Vacuum

My Hoover Windtunnel Ultra U6425-900 began shutting off after a few minutes of vacuuming. The time interval became shorter and shorter. If I leave it sit a while, it will start again. This does not happen when I used the attachments - only with the floor brushes. The switch has recently been replaced and the whole vacuum serviced by a Hoover dealer about a year ago. I have been told by a local repair shop(not a Hoover dealer) that it is the motor, there is nothing to do other than replace t

... Hoover Vacuums

Poor cleaning I recently bought the Shark Steam Mop as I read mainly fantastic reviews. I was disappointed to find that it leaves a slight film on my dark hardwood floors when finished. I can wipe the film away with my finger and you can see foot prints if walked over. I also found that there are cloth streaks on my ceramic floors after drying as well. I followed all instructions, vacuumed beforehand, used distilled water even though my water is not considered hard, cleaned slowly, etc. I am wo

Hi,This type of problem usually is not he fault of the Shark Steam Mop.The problem is the old residue left on the floors by other cleaners.Here is a tip that I wrote that will help you out with that problem... ... Euro-Pro Shark Steam Mop - Gray/ Purple Vacuum

New and old markings on oreck roller brush - Oreck Vacuums

... Oreck Vacuums

My dyson dc07 brush bar seems to be only spinning at half speed. Leaves three light streaks in the vacuum marks like somethings just dragging. Brush bar is clear and filters are clean. Seems like there's slipping somewhere.

The belt is stretch and so it is slipping on the motor shaft. You need to change the belt. Here is a link for the\015\012instructions on how to change the belt and a link for the belt you need: ... Dyson DC07 Bagless Upright Cyclonic Vacuum

My Oreck is hopping on my carpet while vacuuming. It is fine when pushed away - it hops and leaves marks on my carpet when I pull it back. I have changed the bag and cleaned off the roller and checked for a clog. All are fine.

My first thought is to change the belt.If it is stretched this is a common symptom.You can go to youtube and my chanell is sewvacmd.Their is a video on how to change it.Hope this helps. ... Oreck XL2200 Bagged Upright Vacuum

My new oreck magnesium upright is making a black marks on my hardwood floor. what should i do?

... Oreck XL2200 Bagged Upright Vacuum

Oreck xl the vac will not pick up anything on my hardwood floors. It just pushes it around yet the brush is spinning.

Sounds like the Oreck is clogged. You'll have to undo the bag by the way of the clip in the middle at the back of the main black spindel neck and then at the bottom. Then take apart the main neck by pushing the rubber mounts upwards to release the pi ... Oreck XL2200 Bagged Upright Vacuum

Kirby Sentria My vacuum is leaving scuff marks on my hard wood floor any ways to fix?  please help.. thanks.

Be sure that the brush roller is dusengaged. \012To do this you:\012* Lift up the headlight lamp\012*Turn the handle until the red arrows line up ... Vacuums

Dirt devil vacuum cleaner--trouble vacuuming dirt and pet hair on carpeting --is the problem with the spinning brush which contacts the floor,  not contacting the carpeting??  I thought (when I bought this vacuum) that the aforementioned brush was adjustable to various heights of carpeting.  Sometimes, it seems like nothing is being vacuumed up --unless I have just put a new bag on the vacuum... Do I need or can I replace the spinning brush on the bottom of the vacuum so it kicks up and vacuums

Try replacing the belt. Rubber belts stretch out after about a year. ... Dirt Devil CE6100 Featherlite Upright Vacuum

Need Hoover cannister vacuum floor brush & filter bags

Yes attachment are available just bring your wand into your local vacuum store to insure the proper fit ... Vacuums

For some reason, when I tried to put the floor vacuum attachment back on and vacuum the carpet, I realized that the belt was not engaging. the belt is in there and not broken, but it is not turning the beater brush. it is just hanging loose around the brush. When I turn the wheel to engage the brush, it picks the belt up, but when I attach the vacuum to the attachment, the brush is just not turning.

... Kirby Ultimate G Bagged Upright Vacuum

Stopped running My mother's Oreck vacuum sound as if there was something bogging the rotating brush down. I pulled the bottom cover off and found nothing wrapped around or restricting the brush. I tried to finish vacuuming with the problem then I turned it off to move a chair and turned it back on it would do nothing. Any suggestions as to what could be causing the vacuum to sound as if the rotating brush is being restricted from turning. There was not odor of burning as if the motor was in a bi

Orecks have a plastic fan inside and everything you pick up hits it, sometimes things can get stuck in there or break the fan locking up the motor. With the machine off, poke around where the dirt goes into the motor, behind the roller and see if you ... Oreck XL Ultra Bagged Upright Vacuum

I live in Mexico and have a Electrolux Easy Box Vacuum...I am looking for a hard floor brush that will fit the hose as my old Sears brushes are a little too small.This model is bagless and may only be sold here,but I do not care for the floor/rug brush combo brush as it does not clean tile floors very well.I would order and have a friend in the states bring to me.Thank you,Linda Staton Cozumel Mexico

... Electrolux Vacuums

My vacuum's cyclonic action is not spinning and creating very little vacuum pressure through hose or floor brush area. I already checked, brushes are spinning, there is no apparent blockage in the canister, I took it completely apart and removed excess dust from the filter. Still no good vacuum. Any suggestions?

The following filter in your in your dump cup needs to be replaced. \015\012F24 Dirt Devil "I" Bagless Upright Vacuum Replacement Filter Style F24 ... Dirt Devil M130005 Bagless Upright Cyclonic Vacuum

LlllSteam vac ws working very well--shilfted to using hand vac on furniture--when I shiftead back to wanting to use the floor vacuum using the 6 brushes and the floor vac system, the r6 rotaty brushes will not turn or function. What do IO havae to do to get them to turn and function? The lever on the side ils set for carpet terrain. What do I do now to get brushed to turn and scrub as they should and did previously. James Yerges 1'630-232-2798 JMYerges&comcast.net

What is the exact model number of that unit. There are several with that name. The only things that it could be are the handle mechanism that activates the brushes or the indicator is not working nad the level that selects the brushes is not working. ... Hoover Vacuums

It leaves dirt and fluff in the rollers not in the filter. So is not cleaning properly. There is never anf fluff at all in the filter. Also the lid does not close properly and we constantly get the 'check tank' light coming on. It leaves streaky marks across the floor and seems to leave the floor too wet (hence the streaks). Look forward to hearing from you.

Is there something stuck in the air passage between the tank and inlet ... iRobot 5800 Scooba Vacuum

I have an electrolux renaisence vacuum. the brush in the floor attachment turns but I have no suction. When I change to bare floor option on the handle the brush stops turning (correct) but I still have no suction. The lights on the handle showing --floor,carpet, high and low all work.

Sounds like you have a clog, either in the hose or the inlet by the brush roll. ... Vacuums

Dc07 when vacuuming motor and roller part will not stay on floor , as you pull and push the vacuum the brushes keep lifting up and I have to push it down onto the floor how do I fix this?

Most dc o7 do require a little wd40 at the hinges however if problem isn't fixed try looking and making sure all the peices are snapped in like they're supposed to be. hope this helps ... Dyson DC07 Bagless Upright Cyclonic Vacuum

The bottom bar that encases the brush is flush to the floor when using the vacuum. This causes the suction to "stick" the vacuum to the floor (lamenate) and also as there is no ground clearance debris is just pushed around. We have to nearly stand the thing upright to get the ground clearance to be enough for things to start being sucked up. I have taken apart, re-assembled etc and nothing is working.

I'm having the same problem.  The bottom plate is not level with the floor unless the vacuum is nearly in the upright position.  Its like there should be a spring pushing the bottom plate towards the floor.  Anyone know how to fix this ... Dyson DC07 Bagless Upright Cyclonic Vacuum

I purchased a Miele Model S518 vacuum cleaner yesterday at Canadian Tire but they could not find the manual or floor brush. I would like a manual please? and how much is a new floor brush?

... Miele Leo S5381 Canister HEPA Vacuum Cleaner Bagged Vacuum

Roller Brush How do I install the roller brush. I didn't pay attention when I removed it and now when I attempt to vacuum my low carpet it doesn't seem to be working. The green light on the head of the vacuum goes out when I click it down to the floor. It didn't used to do that. Plus I think I smell something burning. Could the belt be broken?

Try a new belt. The ends of the brushroller are different sizes, so you can't put it in backwards. There are numbers and notches on the ends of the brushroll. These notches/numbers need to match on both sides when installing it. (probably need b ... Kirby Ultimate G Bagged Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1284 seconds