Having problems with your Oreck XL Ultra Bagged Upright Vacuum ?

Oreck trouble I replaced the plug and switch. black from motor to pole 1, black from plug to pole 2, white tied to white with a wire nut. When I plug it in it is powered in the off position. I have high speed at the high speed position, low speed at the low and off positions. Any ideas?


Answers :

Repair Help & Product Troubleshooting for Oreck XL Ultra Bagged Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Oreck trouble I replaced the plug and switch. black from motor to pole 1, black from plug to pole 2, white tied to white with a wire nut. When I plug it in it is powered in the off position. I have high speed at the high speed position, low speed at the low and off positions. Any ideas?


... Oreck XL Ultra Bagged Upright Vacuum

Royal vacuum cleaner model 4600 wiring diagram I have a Royal Vacumm Power Tank Model 4600. I replaced the switch (6 wire - 3 position) that is on the tank. One side of the switch control just the blower. The other side control the blower and the POWER head - wand with a variable control speed. The middkle position is off. After I installed the swith, the power head - wand is powered in either position. There are three wires comming out of the wand: White, Red and Black. I guess I wired somethin


... Vacuums

The e series rainbow 2 speed works only on low speed. High speed will not run. What is srong?


It is either the switch or the controller. Call us and we can see if it is still covered under your warranty.RainVacwww.rainvac.com800-523-0510 ... Rainbow E series Canister Wet/Dry Vacuum

I have 200 main breaker panel. I want to install a single pole 20 amp breaker. I have 3 wires coming from an outlet, black, white, and green. I have black tied to the circuit breaker, white tied to the bus bar, but I do not see where to attach the ground


Look at the panell ,,the positive connects directly on the breaker ,,the negative on a rail inside the panel,, you will see other wires on the rail..and the ground connects on the panel itself,, you will see a bold ... Vacuums

Oreck XL upright - has a 2 speed switch. Now only works in high speed not low speed. Will a new switch correct or is it the motor


Your vacuum is fine. The switch can either run at full speed or half speed. You are running at full speed, you need a new 2 speed switch. You can pick them up at an Oreck Store for $29 or around $15 on eBay ... Oreck XL Ultra Bagged Upright Vacuum

I HAVE A BLACK & DECKER DUST BUSTER CORDLESS VACUUM. I'VE HAD THE CHARGER PLUGGED IN FOR ALMOST 24 HOURS AND IT IS STILL DEAD. SHOULD THE SWITCH BE IN THE OFF POSITION OR THE MIDDLE POSITION. IT'S BEEN A LONG TIME SINCE I USED THIS VACUUM. IT WAS BURIED IN MY GARAGE


I am not certain about this specific battery, however, if many batteries are unused for a long period of time, they can not be rejuvenated. \012Try the switch in each position for 24 hours and if there is no action, it is probably not worth re ... Black & Decker AV1200 DustBuster Handheld Vacuum

My rainbow vacuum will not start in high speed but runs in low speed


Yes, it sounds as if your controller is bad. Give us a call and we can see if it is still covered under your warranty.RainVacwww.rainvac.com800-523-0510 ... Rainbow E series Canister Wet/Dry Vacuum

I have a Kirby G7 and it will run on the low speed setting. When i switch to the high speed it starts to spark and smoke near the back of the motor near the windings. Do i have a motor going bad or is there a simpler fix.


It's probably doing that on low speed too, you just aren't noticing. What you'll have to do is get to the motor. Look at the armature and see if it's scared, missing an pieces, scratched up.. if so, then your motor is shot, throw it away.. If not, if ... Vacuums

Despite having the small window cleaned out the brushs will not spin at high speed. They turn at the low speed only.


... Hoover V1 SteamVac SpinScrub Vacuum

Hunter Fan model # 27185-060 - Fan high speed does not work - only get low speed by use of the remote- how do i fix this ???


... Vacuums

How do you wire a 2 speed fq motor. I know the blue/blue. the red/red. The yellow /yellow and I believe the whites together with the grey of the pn outlet. Does the black from the motor the black from the cord and the other grey from the pn outlet connect together ?


I have not seen the new two speed but sounds like the wiring is coded to teh switch by colorOn a single speed it would be this way.\015\012\015\012Power cord to side 1 of switch.\015\012Switch to motor 1 and PN receptacle 1, etc ... Filter Queen Cheetah II Ash - MU305 Bagless Canister Vacuum

Hunter Fan Mod 21617-001, wire colors Black with white stripe/ Pink/Yellow/Red/Gray/Black/White. This has a floresent light, no chains or switches. The Pink serves the light. Note the wires are not labeled but I assume go to different speeds on the fan. Attempting to utilize the "Universal Remote" Mod 27185 with no joy.


Red and white are twisted together,or however you combine wires.I use plastic wirenuts.Always twist clockwise as the wirenuts are most effective that way and the wires will stay together better.Black/white,yellow,and gray are the speeds yes,and the f ... Vacuums

All light are working just a click when you turn it on, the element is ok 120 volts readings red and black no voltage between red and white I beleave the high limit thermostat againts the heating element is open.yes or no thanks Ron


Hello, YES , that is how it should work, and do not forget that the appliance is 120v , so if you are using 240v , you will need a step down transformer, and if otherwise you can connect direct to the main supply.....I ... Vacuums

I have a Panasonic MCE6003 vacuum cleaner. I regretfully leant it to a neighbour and it came back full of dog hair and keeps cutting out. I cleaned out the dust container and the main filter but it still kept cutting out after 5 minutes. I decided to unscrew the part with the motor and wash the filter inside.It was all going well until a large rubber washer bit, a piece that looks like the thermostat and a little white button attached to two black wires fell out and now I have no idea how to put


... Panasonic Vacuums

I have a Napoleon Pellet stove insert Model NPI40. When the fire burn rate is extremely low it seems to operate normally. However, when I turn the heat up even a little I eventually get a high pitched noise that seems to be coming from the convection blower. Changing the speed of the blower has no effect on the noise level. I cleaned the blower but did not remove it. There was very little dust on it. Cleaning had no effect on the volum or pitch of the noise.


My theory is based upon 1st hand knowledge with a newer EPA compliant freestanding wood burner, with the air-tight and high efficiency ratings.its possible that its just the high rate of air moving through the air chambers , similar to a o ... Kenmore Whispertone 23312 Bagged Canister Vacuum

The Rainbow vacuum doesn't work on high speed, though it will work for low, what could be the problem?


... Rainbow E series Canister Wet/Dry Vacuum

Spin brushes spin freely on steam vac when not attached to cleaner indicator screen not dirty speed selector is in high position brushes are clean spin brush indicator when brushes attached to machine does not rotate


If this is a Hoover Steam vac, the turbine which drives the brushes is bad. If not a Hoover, then what is it, they are different, need brand and model number. ... Vacuums

Nutone Broan CV556 runs continuously and will not shut off until I unplug it.. I disconnected the low voltage wires and it still runs when I plug it in. Inside the top of the vacuum are 3 electrical devices - one looks like a transformer wire -- one is a rectangular electronic black box. The third is an on off rocker switch. Which piece it likely to be shorted out? It is about 8 years old.


... Broan-NuTone CV556 Cyclonic Bagless Central System Vacuum

Why does a ceiling fan hum in low but not in medium, or high speeds


Because it may need maintenance. I would suggest you remove it and give it some lubrication in the motor and all moving parts. Once you do this it would hardly hum. Hope this helps. ... Vacuums

I have a lakewood fan hv20cr fan and it will only work on high speed. low and mid spin very slow with a bad hum. How can I fix it? where can I get parts for it.


... Lakewood Vacuums

I bought a Tacsew T8700 High Speed Stright Stitch and I should have paid more attention to the 'High Speed'! The motor that came with this industrial machine is a Tacsew Clutch Motor model: RM1878-1H. It is way too fast when starting out and usually breaks the thread. The local company I bought it from told me there was not a user manual for the machine or the motor :P. I've finally gottin the tensions adjudsted but still need to be able to start sewing at a slower speed. Any advice out the


If you are just starting off sewing and don't have good foot control change the motor to a d/c motor they are about $120 and you can turn the speed of the motor up or down ... Vacuums

Trying to wire aa Nutone model 763RL bath exhaust fan/light. The conduit coming from the breaker box has a red wire, a black wire, a white wire and a ground. The fan has two white wires, one black wire, one blue wire and one green wire. I have wired the whites together, but do not know how to wire the blance.


... Vacuums

Replaced Oreck power switch. 2 black leads and 1 white lead for switch. Posts marked 1, 2, and 3. 2 black wires to switch powers on. Connect white wire and breaker trips. Where does the white wire go?


Both black go to the switch. Power in - black to switch / white to white from motor. From motor - black to switch / white to white from power cord The black wire from the power hooks to ... Vacuums

Filter Queen Magestic on switch started smoking will not work on high speed


... Filter Queen Majestic Canister Vacuum

Motor wiring My Vax VS19TL motor died and I have managed to get hold of a new Vax 006 Turboforce motor which is the same size . My problem is that the original motor had two wires (black and white) which ran to the PCB switch. The new motor has three wires (black, white and yellow). I have ordered the PCB wiring loom for the 006 motor but I can't find any documentation that tells me where each wire goes. Can anyone help?


... VAX Appliances Vax X5 Bagless Upright Cyclonic Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0474 seconds