Having problems with your Oreck XL Ultra Bagged Upright Vacuum ?

How to open the handle of an oreck magnesium upright


Answers :

Repair Help & Product Troubleshooting for Oreck XL Ultra Bagged Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

How to open the handle of an oreck magnesium upright


... Oreck XL Ultra Bagged Upright Vacuum

My Oreck Upright will not stay upright! The handle falls over everytime I leave it stand on its own.


What you are in need of is what they call a detent. There is a possibility that is has broken off from the housing which means that the only way to repair it properly is to replace the entire housing. It may have just had the screw come loose and h ... Oreck XL® Classic Bagged Upright Vacuum

Oreck upright handle falls over


... Oreck XL Ultra Bagged Upright Vacuum

The metal rod inside the handle fell out when i separated the two handle parts to replace the square metal post/handle. I do not see a purpose for the metal rod or where it connects near the on/off switch. XL upright Oreck model.


It is like a static ground post your right it really dosent do anything ... Oreck XL2000 Bagged Upright Vacuum

My Electrolux Regency Series upright vacuum brush motor does not activate. Cleaned the brush and press reset to no avail. Opened handle switch assembly and checked each wire attached to all three switch settings. Tried disassembling brush assembly but could not pry open after removing all screws.


... Electrolux Vacuums

Oreck Upright Hi Redev, I'm not sure what model I have (about 6 years old...upright, looks like the one in the picture). I changed the belt (which was torn) and then the next time I used it, it cut off on me. Now if won't turn on at all. (I turn the switch on and off and nothing happens as if it is not plugged in but it is!). I noticed at the top where the power cord enters the handle, it is all frayed. Could the electrical wires have detached? Anything you think I should check before taking it


The cord could be bad and will ahve to be replaced. It would have to have a problem inside the handle or down by the motor. ... Oreck XL2600 Vacuum

Bissell 35962 Cleanview Bagless Revolution Upright Vacuum hose is clogged with sock where hose meets handle attachment. Attempted to use broom handle to push back through suction opening. Sock is compacted. Any home repair advice?


If you have access to a small sink "snake" used to clear clogs in sinks, you might be able to use it to "snag" the sock and pull it out.\015\012Needs to be a metal sewer snake so that you can tug on it if and when it snags the sock. ... Bissell 35962 Cleanview Bagless Revolution UprightVacuum

Oreck xl21 loose handle - Oreck XL21 Bagged Upright Vacuum


... Oreck XL21 Bagged Upright Vacuum

How do you remove the handle to clean it? - Oreck XL21 Bagged Upright Vacuum


I am unsure why you would be removing the handle to clean it. It really is not necessary, but the handle grip is held together with 6 screws, take out the screws the two halves come off of the handle pipe.\012 \012 ... Oreck XL21 Bagged Upright Vacuum

Hi, I have an Upright Vacuum. Unfortunately, the box that contains the Dust container handle, and the Dust container pipe, has broken the base. It is right where we open it to clean the pipe. It is possible to buy the whole tube? Alicia


Hi, yes it is possible to buy the whole tube replacement but you have to get in touch with the manufacturer of the vacuum cleaner to make a request for the needed parts.Take care ... Vacuums

The handle broke off what do I do? - Oreck XL2200 Bagged Upright Vacuum


We have that part available here. Just double check your exact model number, we also have the handle grips, screws and cords. ... Oreck XL2200 Bagged Upright Vacuum

My new oreck magnesium upright is making a black marks on my hardwood floor. what should i do?


... Oreck XL2200 Bagged Upright Vacuum

Oreck XL Ultra Bagged Upright Vacuum Loose handle


... Oreck XL Ultra Bagged Upright Vacuum

Orek website diagram for wiring orek handle - Oreck XL Ultra Bagged Upright Vacuum


... Oreck XL Ultra Bagged Upright Vacuum

Oreck xl9100 runs okay when upright but when the handle is at an angle the motor stops


You must test the power cord for open or break use the VOM2) Test for main switch some wires loose, or bad solder, or switch defective, and replace.3) Thermal fuse, loose, or bad contact. tight.4) See if the belt is sliping or broke or wo ... Vacuums

My Oreck is 10+ years old. The bag will not remain on the opening of the handle inside the bag. Dust goes into the cover rather than in the bag getting in the zipper which makes it very difficult to unzip the cover. Any suggestions?


Check and make sure bag collar is behind the two lips. if it isn't it will leak dust and make it hard to open. ... Oreck XL Ultra Bagged Upright Vacuum

Reassemble of handle on upright


Place handle half with the posts that hold the screws facing up.\015\012\015\012silver pole with hole that goes completely throuigh goes over lower screw post (Long side) \015\012\015\012static wire - L shaped end goes in smal ... Oreck XL2200 Bagged Upright Vacuum

Miele S5000 (revolution 5000) vacuum cleaner - How do I open the casing? When the power button on the handle is pressed the green power-level lights on the handle light, but the motor sounds like it gives a little 'jump' but nothing more. The orange power light on the body also dims. I assume the motor or fan is jammed, but I can't open the body to find out. I've taken out to screws inside near either end of the handle, but to no apparent effect. I'm assuming the body is held together by plastic


... Vacuums

Placing the handle of my Dyson DC07 into its upright and locked position causes the beater bar to stop turning. It will not start turning until the handle is first lowered to the working position and the Carpet/Bare knob is moved to the Bare Floor position and then back to the Carpet position. Then the beater bar turns until the handle is placed into the upright position. What might be the problem?


Hi its Darran at Dyson.The brush control is designed to switch the brush bar off automatically when you stand the machine back into the upright position. It is designed this way to protect any delicate floor surfaces when you have the ma ... Dyson DC07 Bagless Upright Cyclonic Vacuum

How to unclog the Oreck XL upright? - Oreck XL2200 Bagged Upright Vacuum


... Oreck XL2200 Bagged Upright Vacuum

How to detach oreck upright bag to wash


... Oreck XL Ultra Bagged Upright Vacuum

How to replace motor on oreck xl upright - Oreck XL Ultra Bagged Upright Vacuum


... Oreck XL Ultra Bagged Upright Vacuum

Oreck XL Handle wiring


... Oreck XL Ultra Bagged Upright Vacuum

Oreck XL vacuum will no longer lock in the upright position.


... Oreck XL Ultra Bagged Upright Vacuum

Oreck upright hard to push - Oreck XL2000 Bagged Upright Vacuum


If hard to push, only a few things to check:\015\012\015\012(1) Rear wheels will get hair or thread wrapped around axles, dust, etc. and be hard to turn. Make sure each wheel turns easily.\015\012\015\012(2) Small wheels on ne ... Oreck XL2000 Bagged Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0544 seconds