Having problems with your Panasonic Bagless Upright Vacuum Cleaner MCUL915 ?

Panasonic upright vacuum brushes dont turn - Panasonic Bagless Upright Vacuum Cleaner MCUL915


Answers :

This may be too obvious, but do you have the Carpet switch turned on (bottom left of vac). Agitator brush does not go around if Floor/Tools is switched on,
Repair Help & Product Troubleshooting for Panasonic Bagless Upright Vacuum Cleaner MCUL915

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Panasonic upright vacuum brushes dont turn - Panasonic Bagless Upright Vacuum Cleaner MCUL915


This may be too obvious, but do you have the Carpet switch turned on (bottom left of vac). Agitator brush does not go around if Floor/Tools is switched on, ... Panasonic Bagless Upright Vacuum Cleaner MCUL915

I have a problem with my model 6585-3 bissell upright powerforce bagless turbo with turbo brush vacuum The brush has quit spinning upon removal i noticed that one side of the brush was free to spin the other side that has the rectangular piece to help hold into place seems to be locked up and will not spin is it corroded or have i lost a piece that joins with it that allows it to spin freely belts are good and motor is turning brush will not budge


... Vacuums

My brush will not turn on my Bissell 6393 upright bagless vacuum... what is wrong? The belt broke and I replaced it twice... I now have 6 more replacements but the brush still won't rotate. Do I have to get a new brush?


This type of plastic brush roll fails pretty frequently. Hair and other debis gets jammed in the end caps. The hair and debris gets hot which in turn tends to melt the plastic end caps. Remove your brush roll, hold the ends with your fingers and try ... Vacuums

Shark Euro-pro EP621 Bagless Upright Vacuum. Q regarding the brush not spinning / after troubleshooting and taking actions listed below, it now spinning for a few secs, but then stopping. Already removed hair, strings, etc. Checked that belt is aligned properly, checked that small wheel that turns belt is working (spins fine when belt removed. Oiled the turning parts a bit, that made it spin better, but still stops. It turns about 3-4 seconds then stops. If I switch it off and on again, I get ag


... Euro-Pro EP621 Bagless Upright Vacuum

DYSON VACUUM BRUSH WON'T TURN - Dyson DC15 Animal Bagless Upright Cyclonic Vacuum


The problem will most likely be either with the PCB under a panel on the side of the chassis, or the small wires from it that feed the front brush motor. \012\012If you are technically inclined, you can ask for more detail on the repair here: ... Dyson DC15 Animal Bagless Upright Cyclonic Vacuum

Bissell 82H1 vacuum brush won't turn - Bissell 82H1 Cleanview Helix Bagless Upright Vacuum


... Bissell 82H1 Cleanview Helix Bagless Upright Vacuum

Vax upright brush bar not turning - VAX Appliances VZL-6012 Bagless Upright Vacuum


... VAX Appliances VZL-6012 Bagless Upright Vacuum

The brush quit turning while i was vacuuming - Dyson DC07 Bagless Upright Cyclonic Vacuum


Could be some debris is caught in brush or belt broke. ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Now that I just fixed my Lux Legacy canister vacuum, I need help on my other Electrolux Regency Series upright! The vacuum works fine but the rotating brush does not work and the brush motor does not turn on. Tried cleaning the brush and hitting hte reset button to no avail. This upright has a triple setting switch and I checked the each of the wires seem to be attached. Tried rotating the brush by hand and it would not budge. Was going to "encourage" the brush to turn with a set of articula


There are a couple rectangular holes on the bottom of the power nozzle, beside the wheels. These have tabs in them that need released with a standard screwdriver. \015\012 ... Vacuums

Hoover WHS2001 2000W Bagless Pet Upright Vacuum Cleaner brushes won't turn even by hand, just delivered new but no instructions


... Hoover Vacuums

My Dyson Blueprint bagless rollerball vacuum brush refuses to turn every so often. Everything is connected properly, nothing is clogged in the brush, the vacuum power is turned on and then the brush bar control is released, but the brush still does not turn.


... Dyson Vacuums

BISSELL - Lift-Off Revolution Pet Bagless Upright Vacuum main brush stopped turning


Check your belt ... Bissell Vacuums

Brush won't turn - Bissell Healthy Home HEPA Bagless Upright Vacuum - Metallic Blue


Remove the bottom plate and check the belt for breakage. If it is, it will need to be replaced. Remove the brush assembly and check the end bearings for debris accumulation. Clean the brush bearing ends and the bearing interiors. Re-lube with 3-1 oil ... Bissell Healthy Home HEPA Bagless Upright Vacuum - Metallic Blue

Brush doesn't turn when on carpet - Bissell 3920 Bagless Upright Vacuum


This sounds like the beater brush drive belt is either slipping, off the pulley, or broken. Unplug the vac, turn the unit over, and remove the bottom plate which may require you take out some screws.\015\012\015\012Depending on your mode ... Bissell 3920 Bagless Upright Vacuum

Brush not turning - Dyson DC07 Animal Bagless Upright Cyclonic Vacuum


That is usually caused by a worn, stretched or broken drive belt. Here is a link to the replacement belts you need and to a manual that you can view which has instructions. It's really simple. ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Brush won't turn. - Bissell 5770 Healthy Home Bagless Upright Cyclonic Vacuum


Is the grey "brush" button on the handle depressed? Brush won't turn unless the button is down ... Bissell 5770 Healthy Home Bagless Upright Cyclonic Vacuum

Brush won't turn, belts intact - Hoover U5753-900 WindTunnel Bagless Upright Vacuum


Even though the belt is intact it can still be stretched and not turn the brush. You can get replacement belts here:www.vacbelts.com ... Hoover U5753-900 WindTunnel Bagless Upright Vacuum

Dyson Animal handheld brush not turning - Dyson DC07 Animal Bagless Upright Cyclonic Vacuum


Hi its Darran at Dyson.We would recommend checking it for a blockage and a removing any hair or fibres from the brush bar. As the brush bar relies on the suction power of your machine, it would be worth cleaning the filter and ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Brushes won't turn but vacume runs - Dyson DC07 Bagless Upright Cyclonic Vacuum


I suggest you check the drive belt, located under a cover on the bottom of the unit. It may appear to be good (tight and not worn) but 9 times out of 10 that is the problem. ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Brush roll turning very slow - Eureka 5893AVZ Bagless Upright Cyclonic Vacuum


You might need to clean out the roller brush. Here is the manual that has instructions:Owner's Guide (1.5 MB download)If you need a ... Eureka 5893AVZ Bagless Upright Cyclonic Vacuum

Roller brush does not turn - Hoover U6630-900 WindTunnel Bagless Upright Vacuum


The drive belt is worn. you can get the replacement belt here:http://vacbelts.com/hoover-windtunnel-38528-035-belt.htm ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

Roller brush does not turn when vacum is on - Dyson DC07 Bagless Upright Cyclonic Vacuum


The belt is broken or stretched. You can get replacement belts for the DC07 here:Belt for DC07 with clutch ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Brush won't turn even though belt is fine - Dyson DC14 Animal Bagless Upright Cyclonic Vacuum


Hi.\015\012\015\012Ensure drive selector knob is not stuck on park or stop when you lower handle to vacuum if it is pull handle back & turn knob by hand to drive position.\015\012\015\012If you have done all this & sti ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

Brush doesn't turn and belt apears good - Dyson DC07 Bagless Upright Cyclonic Vacuum


If your unit has a large knob on the right side of the cleaner head as you hold it when cleaning then your unit has a clutch this clutch has two belts in it so the brush belt may appear ok but the motor belt might be broken it is not an easy repaer ... Dyson DC07 Bagless Upright Cyclonic Vacuum

DC07 brush does not turn - belt intact - Dyson DC07 Animal Bagless Upright Cyclonic Vacuum


Hi there, The problem is likely to be \012a) The selector on the front of your machine is set to hard floors\012b) The ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1556 seconds