Having problems with your Panasonic MC-E583 Bagged Upright Vacuum ?
Can i still buy new brushes for my panasonic mce468
Repair Help & Product Troubleshooting for Panasonic MC-E583 Bagged Upright Vacuum
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
Can i still buy new brushes for my panasonic mce468
... Panasonic MC-E583 Bagged Upright Vacuum
I havethe first generation purple Dyson Animal model. The brush rotates fine, but doesn't make sufficient contact with the floor/carpet, therefore does not pick up most items on carpets (suction still works however). If I put my foot on it and push down a little, it works. However, since I'm not an accomplished acrobat, this is not easy to do. :-) Any suggestions on whether this is fixable? Or should I just save up to buy a new one?
... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum
I have an 6 month old Dyson 33. Likely need to replace clutch asymbly but still need to change belt's. How do you change those belts without buying another new vacume? Can not remove clutch asym
Here is a video of the dyson clutch change on DC07 witch is the same for DC33 ... Dyson DC-33 MultiFloor Upright Vacuum Cleaner
Brand new Hoover Max Extract Deep Cleaner brushes won't turn. Read manual. Checked filters - all clear. Set Spin Scrub Mode Selector to a scrub setting. Brushes still won,t turn. However the brushes on the Spin Scrub hand tool rotate.
Keep getting message 'please remove and clean Roomba's brushes'. Have removed and cleaned brushes and even fitted new one's but still getting message. Also brushes sometimes rotate, sometimes not and not picking up very well at all. Help!
Must be your inbox is full, Delete old / unwanted messages. It should resolve the problem ... iRobot Roomba 500 Series Virtual Wall Lighthouse 80201 Robotic Vacuum
My brush will not turn on my Bissell 6393 upright bagless vacuum... what is wrong? The belt broke and I replaced it twice... I now have 6 more replacements but the brush still won't rotate. Do I have to get a new brush?
This type of plastic brush roll fails pretty frequently. Hair and other debis gets jammed in the end caps. The hair and debris gets hot which in turn tends to melt the plastic end caps. Remove your brush roll, hold the ends with your fingers and try ... Vacuums
Where can I order the following parts for my 1952 KENMORE SEWING MACHINE MODEL #117583, SERIAL #48054: : #5107 carbon motor brush (2) #5110 motor brush spring (2) #5111 motor brush spring cap (2) String for starter control lever Pulleys, screw and nut washer to attach string control Best sewing machine ever and still working like new, and I want to keep it that way. Thanks.
I have a Bissell Lift-off Revolution Turbo vacuum and the brush doesn't spin on its own anymore. Does this mean the motor is busted because there's no noise when you press the brush button. We've just replaced the belt, hepa filter and a new brush. But its still the same. What's wrong with my vacuum?
Its probably the motor. remove the covers with a #2 phillips head screwdriver and cut the wires to the motor ( unplugged ). purchase some crimps at radio shack to resplice the wires together in the same fashion. ... Bissell Vacuums
I have a CT600 power brush that would not power up. Thinking the motor was bad in it, I replaced it with a new CT700 power brush, I am still experiencing the same problem the power brush itself does not seem to be getting electic power, but the Vacuum unit does come on with suction.
First try connecting the power nozzle directly to the hose. If it works, the problem is due to a broken wire or faulty connection in the wands. At least one wand will need to be replaced.\015\012My guess is it's probably due to a broken or di ... Broan-NuTone VX550 Bagged Central System Vacuum
Dyson DC04 is making a grinding sound & smells of burning. Hi. I have been told that the above is due to the carbon motor brushes burning out. The brush at the bottom still turns ok. I have bought 2 new carbon brushes & wondered how I would go about replacing them. Any help would be much apprecieated!
Hi there SmartAlec from NelsonVacuums.com.au here, this is not a repair for the faint hearted. First i am assuming you are not using a clutch model - with a selector for ca ... Vacuums
Hi, i have a panasonic eco max, the brush has stopped going round, the belt is as new and brushes clean.suction good from hose. Any ideas please? thank you
The brush on this model is controlled by the on/carpet/floor switch and will only work in the carpet position. If the suction motor is running then it could be the roller brush motor, but it's more likely to be the microswitch which stops the ... Panasonic Mc-Ul594 Eco Max - Bagless Upright Cleaner
Hi There I have got a Kirby 2 HG vaccum cleaner which is around 20 years old now. It was going really well until last week when one of the capacitors which are connected to the brushes blew up. There is two capacitors one for each brush. One of them completely blew to bits and the other one is still intact. My question is are they the same size and where do I get a new one from. I know it is an old machine, but I would like to fix it and get it going again. Any tips???
Http://www.geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=541405\015\012Generic problem for all Vacuums\015\012Hi There I have got a\015\012Posted by opfinder on Apr 24, ... Vacuums
I have an electrolux genesis upright vacuum that I bought used about 8 years ago. It has been A great vacuum the best I ever had. I thought the belt had come off so I took it in for repair. They called today and said that the brush rotor motor was bad and it would be around 148.00 dollars to repair. My question is could I buy the part and have my husband replace it or would it be too complicated. Can you still buy an electrolux vacuum comparable to this one and how much are they. I love this vac
In my (almost new) Dyson DC31 Animal the rolling brush tends to stop like the bearing was kind of difficult to turn. I opened the side carter and removed the little belt. Without the belt the engine runs regularly. I cleaned the little knots of hairs trapped in the bearing but still the brush runs for a while then stops, tries for a bit then stops again. I even tryed putting a bit of synthetic lubricant with apparently no result. Could it be a defective bearing? Thanks for your help.
... Dyson DC31 Animal Bagless Handheld Cyclonic Vacuum
I have bought new Hoover bags on two occasions. The first spares I bought were the Xxxl variety and I didn't think they fitted that well. The next spares I bought were the type g megafilt. I still feel like they do not fit that well and the suction power on the vacuum is not as good. I'm I buying the correct replacements? I followed the guidelines on the Hoover bags the vacuum came with. These were printed as the right bags to buy. I only have the vacuum around a year and thought it was brillian
... Bosch BSG71310UC Bagged Canister Vacuum
The belt on the beater brush is too loose and the brush won't turn, I have ordered new belts and it still doesn't work!!
Look in your manual for the proper routing of the belt, there may be piece broken and missing without you realizing it. If this not the case, there has to be some kind of adjustment on this unit. ... Hoover U5780-900 Windtunnel Cyclonic Bagless UprightVacuum
Unbeknownst to me, someone took the bag out of my Kenmore Progressive vacuum and failed to replace it. I have been vacuuming without a bag for months, and today the vacuum stopped sucking. When I opened up the front to replace the bag, tons of dirt and dust came pouring out. I thoroughly cleaned the vacuum, put in a new bag, but still no sucking power. Just dust coming from the rear vents where one of the filters is. Is the vacuum ruined, or is it a simple solution of buying a new filter?
Sounds like you need to buy a new motor. All that grit and dust will ruin a motor and I'm surprised it lasted as long as it did.\015\012This is where a vacuum that won't run without a bag would have been nice. (Aerus for one) ... Kenmore 31913 Progressive Direct Drive Bagged Upright Vacuum
Flames and fine carbon particles came out of my Dydon DC29 which also partly melted the bottom filter. The motor is still working tho. I feel that the brushes are gone. How to get to the motor and where to get new brushes???
Hi Joel,I'm sorry to hear about your experience with your DC29. We'd appreciate the opportunity to provide further assistance, so if possible, please call us on 1800 239 766. Alternatively, if you email your contact details to us at ... Dyson Vacuums
I bought a small 5 inch scunci vent brush about 6 months ago at a Raley's store and lost it and need to buy a new one and now they don't sell them anymore. How could I get one?
Have you looked on the web? That's how I find everything I need that isn't in current production or not carried by my favorite stores any longer. Most manufacturers list their larger vendors. If a vendor (retail store) is not close to you, email t ... Scunci Vacuums
We have a new hoover bagless that is a couple months old. The pet hair attachment stopped working. I disassembled it found lots of hair wound around the various rollers and removed - painstakingly thorough i might add. Problem is the brush still wont spin and now the belt seems loose - I think I put it all back together correctly but wondering if there is a trick to this?
Without the model number, I can't look it up, but this has a 1 years warranty on it, maybe take it to a warranty shop. Just take proof of purchase, model and serial numbers. ... Vacuums
Reset button The drive belt on my machine broke. They sent me a new one and I installed it, I think, correctly. It still won't engage and rotate the brushes. I can't find a reset button, but I suspect it needs to be reset. Where is the button? Theresa
Do the brush rolls turn ok? The brush roll motor may be bad.\015\012\015\012 ... Bissell 9400 ProHeat Upright Wet/Dry Vacuum
I INSTALLED A NEW BELT BUT THE ROTER BRUSH IS STILL NOT TURNING
It's possible that when you replaced the belt, you may have pinch it against part of the vacuum. Or, you may have put the brush in crooked.Jim ... Kenmore Vacuums
New morphy richards vacuum cleaner 73288 belt went first time of use. replaced it and now brushes still do not go round hard to push
... Morphy Richards Vacuums
Terrible noise My dyson was working great then started making this horrible noise. I cleaned the bar but noise is still there. I discovered the beater bar went around three passes then froze and started horrible noise again. my husband got the bar turning but after 2 swipes vacuuming it did it again. Can it be fixed or is it time to retire it and buy a new one. Wendy Kiser
That noise is the clutch. A very expensive part and very hard to replace. When a problem with the clutch happens it's generally not worth the time and money to replace.I suggest getting a different type of vacuum, maybe a Miele or Sebo. W ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum
Can I buy a new power head and floor brush head for the harmony....bought in 2004-05 and if so where?
Hi, EVacuumStore.com sells a good selection of parts for the EL6985. If they don't have the parts you are looking for, try ... Electrolux Harmony Canister Vacuum - EL6985 Vacuum