Having problems with your Panasonic MC-V5716 Upright Vacuum ?

Not enough suction for Panasonic MC-V5716 upright

\015 Motor protector is admitting loud noise as if blocked -motor runs -roller and belt all run fine. Has suction but not enough hose gets clogged or even short hose gets clogged-do I need to change the motor protector\015

Answers :

Probably not the motor protector, its function is shut off the motor if it overheats. Most likely you have a clog or partial clog in the inlet down by the brush roll, or it is in the hose. But if the motor is running, and suction is low, with no clogs, then maybe the motor is running at a slower speed and will have to be replaced.
Repair Help & Product Troubleshooting for Panasonic MC-V5716 Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Not enough suction for Panasonic MC-V5716 upright


Probably not the motor protector, its function is shut off the motor if it overheats. Most likely you have a clog or partial clog in the inlet down by the brush roll, or it is in the hose. But if the motor is running, and suction is low, with no cl ... Panasonic MC-V5716 Upright Vacuum

Do not have enough suction strength - Dyson DC07i Bagless Upright Vacuum


... Dyson DC07i Bagless Upright Vacuum

The bottom bar that encases the brush is flush to the floor when using the vacuum. This causes the suction to "stick" the vacuum to the floor (lamenate) and also as there is no ground clearance debris is just pushed around. We have to nearly stand the thing upright to get the ground clearance to be enough for things to start being sucked up. I have taken apart, re-assembled etc and nothing is working.


I'm having the same problem.  The bottom plate is not level with the floor unless the vacuum is nearly in the upright position.  Its like there should be a spring pushing the bottom plate towards the floor.  Anyone know how to fix this ... Dyson DC07 Bagless Upright Cyclonic Vacuum

The suction isnt working - Panasonic MC-V5005 Bagged Upright Vacuum


Disconnect the hose where it goes into the base and see if you have suction there.if you don't then your intake hose is clogged.thats the hose that your long stretch hose connects to.take a coat hanger and bend the tip so the end is rounded.work it d ... Panasonic MC-V5005 Bagged Upright Vacuum

When using dyson in upright possition does not pick up very well. roller is going round. when you press front to begin hoovering carpets the front doesnt seem to drop onto floor low enough. dont think suction pipe is engaging properly !!!!!!.


Hi Peter, I'm sorry to hear you're having difficulties with your DC07. It sounds as if the internal hose may have become twisted - you should be able to resolve this by removing and replacing it as shown in the video below. Please make sure t ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Loss of suction in my Hoover Windtunnel bagless selfpropelled upright


There's also the possibility that the fan/impeller has stripped loose from the motor shaft and is basically sitting there while the motor turns. Also, you may have broken vanes on the fan/impeller that will drastically reduce the suction. Replacemen ... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum

Hi...there is no suction in my upright's hose...there is suction when regular carpet cleaning but when I put it in an upright position and take the hose out there is extemely light suction.


... Miele S7210 Bagged Upright Vacuum

S7000 my miele upright vaccum cleaner looses it suction when on carpet mode, suction is perfect when upright (hose). The suction lasts for appox 5 mins when on the carpet and it stops.


... Miele Vacuums

Loss of suction when using upright. Suction remains for samll tools no suction when in upright position makes funny noise but ok when not used in that position kindest regards louis


U can remove the flexi pipe by pressing the inset button,it may be bit stiff if it had not being removed before.may be something is stuck at the bottom,also remove u bend where most of the stuff get stuck. i just posted how i fixed the suction and ... Dyson DC15 All Floors - The Ball Bagless Upright Cyclonic Vacuum

Panasonic MC-E468 vacuum cleaner loss of suction


HI\015\012If the cleaner is loosing suction make sure to check all inspection tubes and the dirt channel hoses after the spinning brush. Also check the main hose for any clogging. One of the worst faults of this model is clogging hoses. Hope that hel ... Panasonic MC-E583 Bagged Upright Vacuum

Hoover upright vacuum lost suction


... Hoover U5258-900 WidePath Bagged Upright Vacuum

Poor suction The actual sweeper seems to work ok, but the hose attachment has some suction but not enough to pick up things I think it should and not enough to make the power brush spin. I've checked everywhere I can for clogs, but I can't see anything. And there doesn't seem to be any way to check to hose itself for clogs. I've cleaned out the container and the filters, but there's still a problem.


Check the inlet down by the brush roll, make sure it is open, if it is then the hose itself must have a clog. If the hose comes off, drop something like a marble in one end and see it it comes out the other end, if it doesn't then you have a clog. ... Dirt Devil M1100009 Reaction Soft Touch Cyclonic Upright Vacuum Cleaner Vacuum

Panasonic upright vacuum brushes dont turn - Panasonic Bagless Upright Vacuum Cleaner MCUL915


This may be too obvious, but do you have the Carpet switch turned on (bottom left of vac). Agitator brush does not go around if Floor/Tools is switched on, ... Panasonic Bagless Upright Vacuum Cleaner MCUL915

After using my attachments I have a hard time getting suction when using upright again - how do I get the suction on my upright? It's a Hoover blue widepath Tempo~ thank you


It may be clogged underneath the vacuum where the roller is. Take the bottom plate off and look into the intake port. There may be some blocking the port. ... Hoover Tempo Widepath Upright Vacuum - Blue

When using my vacum upright its very low in suction, it used to be so powerfull that it lifted my carpet slightly....when using the tools section its as strong as it should be please help, ive cleaned it out but still loss of suction in upright position, from mrs richmond


Check the following items:\015\012\015\012* The bag and connection - change it if it's full\015\012\015\012* Turn the vacuum over and inspect the beater bar area for any clogging. You may have to remove the bottom plate to ... Vacuums

No suction I just replaced the bag, and normally after this I have a lot of suction. Now that I have changed the bag I have less suction that I had before. Not even enough to picj up dog hair. I snaked he hose and checked all of the connections. It seems to have an air leak but no amount of tape will fix this. I cleaned the filer as well with warm water and dried it and re installed but still absolutely no suction. I am ready to throw it out! Any suggestions would be appreciated


1, Does the blower (discharge) side blow bunches of air??Yes: Something is clogged from the bag to the hose end. Try blowing out the hose from the discharge side.Or: The bag is not properly seated. Make sure that the plastic piece is ... Kenmore 23313 Whispertone Bagged Canister Vacuum

Ive got powerful suction from my wand when i am using my dyson upright, so the suction on the bottom not good


... Dyson DC07 Bagless Upright Cyclonic Vacuum

Vacuum won't **** in upright position, but there is suction from the hose in the upright position


Theres a knob that switches it from floors to carpet turn the to floors.please leave feedback ... Vacuums

No suction whether I'm using the tools or using the vacuum upright, there is no suction. I have checked the hose to make it is not clogged- still no suction. What is the problem?


Your intake hose might be clogged at the bottom ,it the clear hose that comes up from the bottom .you will see it from the back.take the dirt cup off there is a filter inside that most likely is clogged ... Dirt Devil M086700 Vision Bagless Upright Vacuum

My eureka optima upright bagless vaccum has VERY low suction using the floor part. the hose has excellent suction. i removed the little translucent door underneath and there were no blockages, i cleaned the brushroll thoroughly and that hasnt helped either. i know this probably isnt recommended but i turned it on to the floor setting with the brushroll off and stuck my fingers up the intake as far as i could, the suction was good further up but it just seems to stop down at the base. because i s


I will try and help here. Is the sole plate on the bottom of the vacuum complety on and there are no visible cracks along the seam where it meets the body? This is the usual cause for this. Onc you take of the plate to access the roller and brushes, ... Eureka 431A Optima Bagless Upright Vacuum

Hoover SteamVac Plus 1200 upright hot water extractor Water/carpet cleaner applying o.k. Suction on the "floor" does not work. Suction on the hand tool works somewhat, but water is not collecting in the bucket. There is suction coming from the floor but water is not going into the bucket. It does not appear to be clogged because I can feel with my hand that air is flowing from the floor. The water is not being sucked into the bucket.


... Hoover Vacuums

No Suction I have very little or no suction on the cleaner. It suctions o.k. with the hand tool, but not the upright cleaner.


Between the top edge of the clear noozle and the lip of the tank that sits on it, there should be a black oblong gasket, if missing, you will have no suction there. The other is the filter on the tank lid, is it clean? ... Bissell 7920 ProHeat Pro-Tech Upright Wet/Dry Vacuum

Need Kirby Generation 3 Vacuum cleaner manual. Vacuum is not picking up dirt from floor. Seems to have enough suction to inflate the bag, but when you check the suction under the vacuum, there seems to be extremely litle suction.


If your brush roll is turning and your bag is not overly full, then the only other thing it can be is a clog where the bag connects to the vacuum. Turn the plastic part out away from vacuum and lift off to see if you have something clogging it. It ... Kirby Generation 3 Bagged Upright Vacuum

Dirt Devil upright doesn't have suction. I changed the belt and the bag. The suction is so slight it won't pick up a small piece of paper. The accessory wand also does not have much suction.


Try cleaning chute that fills bag.may be obstruction blocking the flow of air ... Vacuums

Dyson DC07 bagless - upright mode v poor suction, wand mode ok


I suffered with a serviced but not sucking DC07, its fixed now. How? By replacing the cyclone unit via anotherbay, it was an accumulation of dust and debris in the section that is not accessible. Borrow a working cyclone if you can and check the diff ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0545 seconds