Having problems with your Panasonic MC-V7355 Upright Vacuum ?
I have a Panasonic upright MC-V574400 and the brush doesn't spin. The belt is intact. What could be the problem?
Repair Help & Product Troubleshooting for Panasonic MC-V7355 Upright Vacuum
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
I have a Panasonic upright MC-V574400 and the brush doesn't spin. The belt is intact. What could be the problem? Thank you Christine
... Panasonic MC-V7355 Upright Vacuum
Is there a diagram/picture to help me visualize how to put cleaner belt back in vacuum? I was taking base of vacuum apart so I could get rid of hair that were wrapped on the roller. The cleaner belt came to loose and I could not figure how to fix it back. the model is eureka upright bagless series 430
Hi,Sorry to hear your belt fell out. Not good if you've never replaced a belt before...Here is a website where you can read a detailed description of how to change a belt: http://www.ehow.com/how_8034505_eureka-belt-replacemen ... Eureka 431A Optima Bagless Upright Vacuum
My machine (Hoover Wind Tunnel - bagless) is only 1 yr. old. The agitator brush doesn't turn all the time. I know it's not supposed to turn when in the upright position. However, it only seems to work when I have the setting on high. When I stop, but have not put the machine in the upright position, it stops again and then slowly starts moving. Could the V-belt be worn out already? In the owner's manual it states that this belt is not normally replaced. The exact same thing happened with my old
Sounds like you should do two things:\015\0121- Remove and clean the beater brush of all debris as best you can. At the end of the brush you will see a hard rubber piece, at both ends, that holds it in place in the body of the vacuum.\015\012Add som ... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum
Changeing belt how do you install a new belt? I have an Eureka, The Boss, bagless, upright. The brush is hardly rotating. I think it could be the belt but i cannot open the vacumm to check it. How can I fix this?
Havent used for about two years. I had to put the belt on it. It doesnt seem to be sucking up very well and after about 15 minutes of vaccuuming the bag was empty. My house got really dusty. I know the rollers were spinning because i looked. I could hear some dirt going in but could definatly tell it wasnt working properly. Is it in reverse or something?
After two years you need to make sure the bag is connected properly and inspect it for tears and that the hoses are connected correctly and not deteriorated. Make sure the hose is clear. You should be able to feel the suction at the end of the hose. ... Vacuums
Oreck Upright Hi Redev, I'm not sure what model I have (about 6 years old...upright, looks like the one in the picture). I changed the belt (which was torn) and then the next time I used it, it cut off on me. Now if won't turn on at all. (I turn the switch on and off and nothing happens as if it is not plugged in but it is!). I noticed at the top where the power cord enters the handle, it is all frayed. Could the electrical wires have detached? Anything you think I should check before taking it
The cord could be bad and will ahve to be replaced. It would have to have a problem inside the handle or down by the motor. ... Oreck XL2600 Vacuum
How to replace belt on panasonic v7571 - Panasonic MC-V7571 Upright Vacuum
... Panasonic MC-V7571 Upright Vacuum
Vacuum belt keeps coming off. Need instructions on how to change belt on Panasonic mc-6955 upright vacuum cleaner.
Need to replace 2 belts on the Panasonic MC-UG302 upright hoover and I dont know how to do it. Is it possible to get a brief discription/diagram of fitting belts from somewhere. Tks
... Panasonic Vacuums
Panasonic mc-e4113 Upright vacuum. The belt that drives the brush in front is broken I have found a spare for this but there seems to be a pulley missing on the main drive shaft that the belt needs to fit on. I can't believe that there wouldn't be one? Can anyone tell me if this is the case and if so where I can get one from. Many thanks Sean
... Panasonic Vacuums
How do you change a upright panasonic vacuum belt?
... Panasonic MC-V5454 Upright Vacuum
I have a Sanitaire model SC886 upright vacuum. It's about a year old. I replaced the belt , cleaned bag , checked for blockage in impeller fan and now it makes a noise , like a grinding noise or something . Could you tell me how to fix it ?
The bearings in the motor needs to be checked,or the impeller is damage. ... Eureka SC886 Bagged Upright Vacuum
I have a Panasonic MCV7515 UPRIGHT VACUUM and need to remove the cowling that covers the brushes to clean the hair out of the bearings, but it isn't clear how that can be done without a crowbar or sledgehammer. Removing all the visible screws makes the hindmost part loose, but not the front half. Also, is there an easy way to replace the belt?
... Panasonic MC-V7515 Bagged Upright Vacuum
No suction Great suction through the on-board tools - very, very little while upright. I've replaced the belt recently - brand new bag. The agitator is moving. Where could there be a blockage? Where do I look.
Up inside the bottom of the vacuum there is a hole where the dirt goes in to get to the bag. That's where the clog probably is. ... Riccar 8955 Upright Vacuum
Motor whined loudly. Vacuum failure. Suspect motor failure. Hoover.com doesn't list a replacement motor. Drive also failed - could be secondary belt HOOVER U6323- Power Drive Bagged Upright Regards, Jeffrey
Hello, funI was trying to help you out here. Maybe this will help some? I was going back to some customers that asked questions in the recent past and even farther back. It appeared that no one answered some of them, So, I thought I ... Hoover U6311-930 Power Drive Bagged Upright Vacuum
Belt is melting or burning not sure why - Panasonic MC-V5481 Upright Vacuum
It doesn't matter what or why. Use your owners manual and it will show you how to change the belt. When you open it up whatever is hanging the brush roller up will either show itself or when you remove the brush roller it will fall out. Change the ... Panasonic MC-V5481 Upright Vacuum
Brush doesnt turn belt isnot broken - Dyson DC28 Animal Bagless Upright Vacuum
Hi there,I'm sorry to hear you're having difficulties with your DC28. It's probably best if you get in touch with us directly so we can resolve this issue for you as quickly as possible.You can call us free on 1866MYDYSON - or if you ... Dyson DC28 Animal Bagless Upright Vacuum
No suction I have new belts. Everything is clean. No clogs. When I turn it on it smells like rubber , the brush doesnt spin. Everything seems to be free flowing.. Roller brush isnt stuck on the ends. Took off hose to make sure no clogs anywhere. There is not even suction thru the hose with the handle in upright position.
Generally, the problem is that the belt is not running the brushes. This is caused by one of the following:\015\012\015\012\015\012beater brush is jammed. This is either an object stuck in the brush or im ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum
My Hoover upright vacuum has gotten very loud. I have checked the roller, belts and hoses but I haven't found anything. What could the problem be? thanks
Most Hoover uprights are a "fan first" design, meaning that all dirt enters the motor , hits an impeller fan and is blown from there into the bag. You will need to open the vac, remove the belt and two C shaped clamps holding the motor in place and ... Vacuums
I have a bissell momentum ive broken 2 belts the brush doesnt seem to be spinning they are placed into the side slots correctly what could be the problem?
Most likely your brush needs to be removed and cleaned.\015\012Clean all debris that might be in the bristles of the brush. You will see a holder for the brush on each end that holds it into the frame of the vacuum. The two holders should turn free ... Bissell Vacuum - Momentum Cyclonic 1 ea Bagless Upright Vacuum
I have a Panasonic MC-E3011 and it won't ****. I have checked all the pipes from the beater to the inlet at the dust bag, and they are both clear, pluss the air comming out of the vent at the bottom of the upright (above the beater) casing seems abnormally hot. I have allso checked the the belt and beater bar and they are functioning A1 OK.
... Panasonic MC-V7395 Vacuum
I have an electrolux genesis upright vacuum that I bought used about 8 years ago. It has been A great vacuum the best I ever had. I thought the belt had come off so I took it in for repair. They called today and said that the brush rotor motor was bad and it would be around 148.00 dollars to repair. My question is could I buy the part and have my husband replace it or would it be too complicated. Can you still buy an electrolux vacuum comparable to this one and how much are they. I love this vac
I have a windtunnel upright self-propelled that is very difficult to push, on carpet or hard floors. Seeems that it is stuck to the floor and at times you can smell the rubber from the belts. What could be the problem or problems?
Raise the front. you are trying too hard ... Vacuums
Hoover Upright Bagless WindTunnel does not self propel (U6625-900). Belts are new, Brush turns strongly. Wheels propel forward very weakly and do not reverse when the handle is pulled backward. Is there a mechanical link from the self propel switch to the "transmission" ? Are there any gears that could be worn or not engaging properly?
... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum
Installing new belt - Panasonic Mc-Ul594 Eco Max - Bagless Upright Cleaner
+++++++++++++++++++++++++++++++++++++++++\012\011+>> Unplug the mains lead from electrical socket <<+\012\011+++++++++++++++++++++++++++++++++++++++++\012\012\012\011\342\200\242 Turn cleaner over in flat position.\012\01 ... Panasonic Mc-Ul594 Eco Max - Bagless Upright Cleaner