Having problems with your Panasonic MC-V7380 Vacuum ?

Why does my MCE3011 cut out after a few minutes-it restarts after being switched off and left for a short while?


Answers :

Repair Help & Product Troubleshooting for Panasonic MC-V7380 Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Why does my MCE3011 cut out after a few minutes-it restarts after being switched off and left for a short while?


... Panasonic MC-V7380 Vacuum

We have a dyson dc 07 animal the machine was working fine then switched off after returning to the machine minutes later it wouldnt switch on, i removed on off switch cover and used a short piece of wire across the brown wires flicked the wall switch and it worked, aha i thought faulty switch aquired a new one to no avail and now even the short piece of wire trick doesnt work, has the motor died do you think, it wasnt over heating or making strange noises prior to refusing to work


It could be the motor. I'm having to replace the brushes on my DC 05. It appears that you can only get brushes for the YDK motors in the DYSON, not the Panasonic motor. Which might be saying something about the YDK motors. What happens is that the ca ... Dyson DC05 Cylinder Bagless Canister Cyclonic Vacuum

CLEANER SWITCHES ITSELF OFF AFTER A FEW MINUTES USE. IF LEFT FOR SOME TIME, IT WILL START AGAIN FINE, THEN AFTER A FEW MINUTES MORE USE , IT WILL SWITCH OFF AGAIN.


Check all filters, if they can be washed do so, if not clean or replace. next check for a clog in the machine and in the hoses. the machine as a thermal device that if it senses an overload or getting to hot, the machine will shut itself off for safe ... Vacuums

I have just purchased a new Nilfisk vaccuum cleaner 150 extreme and used it for 5 minutes and switched it offf. When I tried to restart the machine it would not start. I cannotg et it to restart-how to i solve the problem -the power light is on


If you're just purchased it I suggest you need to check where your local Warranty Agent is and take it there for a service. Since this model has an electronic switch (do the lights flash on and the middle one stays green when powered on at the power ... Vacuums

DC07 cuts out and stops after about 1 minute's use. It will restart after being left for c. 5 minutes. It seems, therefore that it must be overheating, but an independent electrician could not find any problem.


... Dyson Vacuums

Roomba circles My Roomba circles for a few minutes, then beeps 9 times and stops. A red exclamation mark appears on the left hand side of the controls. If you persist in restarting it, eventually I have been asked to clear Roombas wheels. As far as I can see, there isn't anything blocking the wheels.


Yes, this is known issue and if your bumper moves freely, you might be facing a sensor fault caused by poor quality of components.Here is a guide to fix ithttp://www.schneordesign.com/Avi/irobot/roomba_mod2.htmHave fun ... iRobot Roomba 560 Robotic Vacuum

I have a BISSELL CLEANVIEW II, I turn the power switch to "on" and am able to clean carpet for 1/2 a minute until the power shuts off in the outlet the vacuum is plugged into! The same repeats itself! I wonder if the motor is damaged or just plain shorted out!


Well yes in deed it is time for a new vac. for the motor bearings or armature are ceasing up ang causing the breaker to pop. if the vac. cord is hot then you know for sure... ... Vacuums

I have a Bissell Proheat 2XTurbo carpet cleaner. No water will come out when I squeeze the trigger. I have filled the solution tank and the water tank. I read the troubleshooting in the manual and have tried turning it off for a minute and restarting and nothing. I took out both tanks and reseated them and nothing. It has sat for over a year but did not have any water in the water tank. Some solution was left in the solution tank. How can I make the water come out? HELP!


Call BISSELL Consumer Services.\015\0121-800-237-7691\015\012Mon-Fri: 8am to 10pm ET\015\012Sat: 9am to 8pm ET ... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum

My electrolux Epic 6500 power nozzle Model N109J will not work. It had an intermittent short which I thought I fixed (some of the insulation on the wires were pinched). I fixed the wires and it worked intermittently for an hour then shut down completely. Could the reset switch have a short? When I press the switch nothing happens.


The switch is definitely a possibility, but other problems can also cause this.\015\012Bad switch, needs replaced.\015\012Broken wiring in power nozzle, wands, hose, or canister.\015\012Bad PN motor.\015\012\015\012I str ... Electrolux Epic 6500 Vacuum

I have an Easy-Flo central vac unit. The handle on the electric hose has a switch on the handle. With the switch on ''O'' in the center, it's off. On the left, is the ''I'' position. The vacuum runs but the power brush doesn't. On the right is the ''II'' position. The switch won't flip that way. It feels stuck. It feels as if there is something underneath of it that won't let it push that direction. I have the switch out of the handle, but I can't seem to get the actual black casing around the


Switches are not usually designed to be dissembled.I would strongly suggest that you dont take the switch apart. you are better off getting a new one. then if you feel like it you can take the old switch apart and if it dosnt work you still hav ... Vacuums

I have a Hoover Elite Rewind model #uh71009. We moved recently and it was jostled around and the red power switch popped out. I put it back in but it's stuck; it stays either left or right, it doesnt move back and forth. It appears there may be another piece missing from the power switch...all I have is the red switch and a tiny cylindrical metal tube with a spring on one end. This piece fits into the hole on the red switch. Inside the vacuum itself where this goes, there is quite a large cavity


... Vacuums

I was changing a light bulb with one of those metal extension rods that unscrew and screw back in the replacement bulbs. It evidently didn't seat correctly and pulled off the bulb and created a quick "poof" type electrical short. I have switched out that bad bulb with a new one and can't get either the fan or lights to work. There doesn't appear to be a reset switch. I also swirched out the wall switch to see if that would make a difference and it does not. Any thoughts or ideas would be appreci


If you have not already done so, I would check at the fuse or circuit breaker panel to see if you have blown a fuse or tripped a breaker. ... Vacuums

Vacuum shots down after a short time, restarts but runs only a short time


Yes that unit has 2 sensors 1 on the motor and 1 on the relay board 1 of them is bad which is making the vacuum shut its like a heat sensors its malfuctioning it shuts the unit down ... Broan-NuTone VX550 Bagged Central System Vacuum

G-5 Kirby self-propel works intermitently. The handle must be jiggled until it engages forward. The same for reverse. Once underway it will continue indefinitely until the need to change direction. Jiggle go forward,jiggle go in reverse. It seems as though it helps to push the handle at an angle to the left depressing the switch on the left side at the base of the vacuum head.


Sounds like a loose wire, the wire is connected to the handle, you may be able to fix this yourself but be careful you can void the warranty by doing it your self. (most people make the problem worse) remember your kirby has a lifetime warranty (limi ... Kirby Ultimate G Bagged Upright Vacuum

The one of the controllers for the electric blanket keeps flashing an "e". The other controller is fine. We switched controllers and the same thing happened. We have unplugged the blanket for several minutes and turned off the controller for several minutes. It always goes back to displaying the "e". It is a warmspun blanket and I cannot find any information on the company so that I can contact them to see about the 5 year warranty.


I did some searching-- and I came up with this Linkedin page-- seems to have some information-- Let me know if it helped-http://www.linkedin.com/companies/jla-homeMack B ... Vacuums

After running for 15 minutes, the windtunnel vacuum cleaner shuts off. It will not restart until it has been off for 30 minutes. Could it be overheating for some reason. All of the filters are clean; the dust tank is empty; the belts have no cracks.


It's not necessarily overheating, but the thermal-fuse is definitely tripping and it takes 30 minutes to reset. There are several causes of this (in most common order):\015\012\015\0121. A blockage in the suction system or a full dust tan ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

How do you access the on/off switch on a Nilfisk King 505? Mine appears to have broken, and I am handy enough that I can replace or maybe fix it - If I can reach it! When I went to switch it on, it gave a very short (half second) turn-over of the motor, and then totally died.


Did it work? Should we suggest other options? ... Vacuums

After switching on it is OK for a few minutes then it starts to scream terribly and i have to switch off


Hi there,The problem you're experiencing sounds unusual. Please get in touch with us, free, on 08002980298 (UK), or 1866MYDYSON (US), so we can run through some checks over the phone.Kind regards,JackDyson Cu ... Dyson DC07 Bagless Upright Cyclonic Vacuum

My Dyson DC15 has suddenly become very reluctant to turn left. This is only the case when it is switched on and irrespective of whether the roller brush is running or not. When the cleaner is switched off it behaves as normal as far as steering is concerned.There is no obvious problem with the ball or steering swivel mechanism. Any ideas ?


Hi its Darran at Dyson. Although strange, I believe we have a solution. It sounds as though the cleaner head hose is blocked. When the machine is running the suction will be pulling against the bloskage causingt he hose to contract and p ... Dyson DC15 All Floors - The Ball Bagless Upright Cyclonic Vacuum

The last time the vacuum cleaner was used the outlet sparked causing it to smoke when turning on vacuum cleaner. I replaced the outlet and plugged it in and things seemed o.k. Today I turned on the vacuum, it stayed on for a mili second and went off. I checked the switch on the vacuum and it showed voltage coming and going, but would not turn on again. I checked all the wires in the area of the switch all seemed o.k. I thought maybe there might be a short in the cord. When I went to plug


... Sharp Twin Energy EC-12TWT4 Bagged Upright Vacuum

Wiring the switch for a kenmore vacuum cleaner I need to know where teh different colored wires go. It had a short in it so I replaced the plug but think I wired it incorrectly. Its a Whispertone 300 model 116.28612790 The canister works but the beater bar doesn't.( it worked before a rewired the switch. Thanks


... Kenmore 23313 Whispertone Bagged Canister Vacuum

My Roomba runs for about 3 minutes, then shuts off. If you push the buttons(S,M,L max etc) it will restart for another 3 minutes. The battery is new???


You will need to remove the debris off the cleaning head module. ... Roomba Robotic Floor Bagless Vacuum

After vaccuuming for less than five minutes, the vaccuum shuts off and we need to unplug it for 5 minutes before it will restart


It sounds like the motor is getting tripped out. It could be caused by having a clog somewhere in the unit, could also be that your filters are clogged. you have 2 filters on that unit. One is under the canister, looks like a drawer that slides out a ... Hoover U5780-900 Windtunnel Cyclonic Bagless UprightVacuum

It runs for a couple of minutes shuts off then restarts 30 seconds later runs a couple of minutes and does this over and over


Most vacuum motors are protected from overheating by a thermal switch that resets after cooling down. Check for blockage in the hose,\015\012power head or a full bag that would block cooling air from cooling the motor.\015\012\015\ ... Tristar Vacuums

DYSON DC05 It just doesnt want to turn on. I switched it off, one minute later I tried to switch it back on and it didnt work. I have washed the filters, checked the tubes and everything seems ok.......any ideas? thank you, Lucie


My friends Dyson DC05 was loosing suction and then it stopped altogether one day. When she took the filters out there was black soot in them so it was obvious that the motor had burnt out. I think this happened because she wasn't cleaning the filters ... Dyson DC05 Cylinder Bagless Canister Cyclonic Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0380 seconds