Having problems with your Panasonic MC-V7395 Vacuum ?

Vacum overheats and starts smoking after 4 minutes of vacuming

\015 Panasonic v7395\015

Answers :

Clean vacuum internally, if the problem persists replace the motor.
Repair Help & Product Troubleshooting for Panasonic MC-V7395 Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Vacum overheats and starts smoking after 4 minutes of vacuming


Clean vacuum internally, if the problem persists replace the motor. ... Panasonic MC-V7395 Vacuum

Vacum started makeing noises from the motor part and starts to smoke alot and it smells bad


... Filter Queen Majestic Canister Vacuum

Smoking belt Hey I have a Eureka 2961 avz bagless vacuum, and if it's on for a few minutes i can smell the belt burning.  If the vacuum is left on any longer the belt starts smoking.  I took the case off and there was a little debris but not much.  Is there a cause and fix or just time to replace the belt?


Belt is slipping because the bearings on the beater brushes, which it turns, are jammed or full of dust. \015\012Alternatively the belt has stretched after being overheated and needs replacing because it now slips. ... Eureka 2961AVZ Bagless Upright Vacuum

Hoover Model U8185-900 beater bar part keeps smoking and burning up We've replaced the part Hoover PCB Display Bridge U8172 three times and the vac beater bar works for about a minute then the part starts to smoke and burns out again. I've taken everything apart but cannot locate anything that would cause this part to burn up. I think if I did not disconnet immediately, he vac would catch my rug on fire. Help? I didn't send back the warranty card, so I can't get any help from Hoover. Any suggest


I'm not sure why this is happening. Perhaps if you would contact Hoover and explain the problem to them such that it appears that there is a safety issue with their product, they might be more cooperative. If that fails, I have had luck writing let ... Hoover U8185-900 Upright Vacuum

Vacuum started smoking and smelled. Yikes! I new it was the belt. Got a new belt replaced it.... with less than a minute it burned up another. The rotor/ pin that the belt goes around that should be spinning right? What do i do to get it to spin?


... Dirt Devil M084600 Dynamite Bagless Upright Vacuum

After a few minutes of using my vacume it starts to smell like burnt rubber. like the belt is burningthe only belt I can see looks fine and is turning the brush


But how tight is the belt and how easy is the brush to turn? if the belt is slopy it will slip on the motor drive spindle,,,and it will get very hot then,,, also if the brush head is tight that makes the belt slip too, ... Hoover U5780-900 Windtunnel Cyclonic Bagless UprightVacuum

I was mixing a cake mix on an old Kitchenaid Hobart Mixer Model 4 C for 5 Minutes and then white smoke started to come out. I don't think the mixer had been used in many years. Is this repairable or should I junk it. Thanks, Bonnie


... Vacuums

A burning smell is coming from my vacuum and it starts to smoke after using it for a couple of minutes


I love those situations... i wish i could be there to help you. anyway, the brushes on the motor could be bad... if the motor gets hot, i wouldn't suggest running it until you fix the motor. click ... Hoover U5753-900 WindTunnel Bagless Upright Vacuum

Firex smoke alarm keeps sounding in a loud piercing tone. put it in hush mode and after it leaves hush mode it takes about 5-10 minutes and starts sounding again. have change batteries and cleaned units with canned air.


... Vacuums

How to fix a vacume that is smoking


Any electrical unit that smokes,is ,not worth repairing ... Eureka 2961AVZ Bagless Upright Vacuum

I have a Eureka Power Plus vacuum, model 4702, type A. To start off, it never really had great suction. Marginal at best. Then today I was vacuuming and smelled something burning and turned off the vacuum. At that point, smoke started pouring out from the bottom of the vacuum so I layed it on it's side and the smoke cleared but I never found the source. Is it safe to turn on again after I let it cool down or is my vacuum "shot?"


... Vacuums

Brush turning slowly while shampooing. It starts out fast, but after a minute or 2 the brush is not spinning very fast. I have powered it off and let it cool down. I just started out so I can't believe the engine is over heating, just doing 2 rooms, can't even get through the first room. If I take the brush attachment off, then put it back on and then turn it on, it spins fast, but after a a few minutes, it's spinning softly/slowly again. Kirby diamond edition


Track not set properly in grooves\015\012there could be a clog or the cleaner has built in feature to slow down heads for better cleaning this does it on its own ... Vacuums

Vacume Overheating My vacum is overheating and then shuts down for awhile but doesn't start again untill the vacum has cooled down.. Are there any heat-relays or something like that that could cause the problem ?


There will be a filter between the cylinder/bag and the engine. If your vacuum has a HEPA filter there will be one on the other side of the engine. Remove both of these and clean them out with water, allow to dry and replace. ... AEG Vacuums

Dyson shuts off in 5 minutes, then starts up 2-3 minutes laters w


I think there's a good chance of a clog that you haven't found. On the Dyson it's fairly easy to remove several covers that give you access. From the collection canister is a tube that runs toward the base. At the bottom of the tube you can remove a ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Our Miele vacuum is only 2/3 years old and seems to have given up the gost, our previous one lasted 15 yrs. The machine starts ok and within 4/5 minutes the power drops down and the hoover comes to a stop and it may re-power itself again within minutes, as of today their is no power when the on button is pressed. What do you think the problem is Thank you.


There is a circut board that is going bad and not providing the power to run the motor. You will need to contact a Miele dealer for that part. It is the only board that is in this machine so they should just need a model number in order to get it ... Oreck XL Ultra Bagged Upright Vacuum

I have a Model U57809RM Hoover Cyclonic which started making a very loud noise. Changed both belts on it but the noise persists. It seems to happen when I put the handle in the 'engage to vacuum' mode. The minute I start to lower it the noise begins. Help!


Hello,You could have a broken fan in the motor and need to replace the fan. If the noise is coming from the brush area of the vacuum, you probably have a broken bearing in your brush roller and would need to replace the brush itself. ... Hoover Vacuums

My Roomba stops within a few minutes of starting it and when I press the button, it says "Remove and Clean Roomba's Brushes." I have removed the brushes and cleaned them thoroughly, but within a few minutes, it stops again and says the same thing.


Hi,Accumulation of hair, dust and dirt in the Gearbox that prevents normal operation of the brushes. As a result, a power output is required to keep the brushes turning. As turning the brushes requires too much power, it con ... iRobot Roomba 4210 Bagless Robotic Vacuum

My wife and I own 6 IRobots: 1 Scuba 1 Dirt Dog 4 House cleaning vacume models All of them are not working, so I decided to try and solve the problems with two of them: One is a dirt dog and the other a house cleaning vacume Rumba. Given: Battery is fully charged Reaction: I start both of them. They run for about 2 to 3 seconds They come to an abrupt stop as if there is a rock in the gears. Help


Both of them have identical issues? Can you please provide the actual part number of them? It should be on the bottom or inside the battery area somewhere.ThanksTim ... iRobot 1100 Dirt Dog Bagless Robotic Vacuum

Pull cord all the way out vacum doesn't start. Push the recoil switch for a second then it will start. Bad connection or new cord needed? Also how do you reinstall the coil? Thank you.


Greetings,\012This definitely sound like a cord reel issue to me. This is really the \012only problem that I ever see on a Miele vacuum cleaner ... Miele S514 Solaris Bagged Canister Vacuum

I was vacuuming and noticed that the bag needed changing. the red light with the ! inside the triangle also came on. When the bag was changed, the vacuum would not restart. The red light came on. Tried the reset button but nothing happened. Tried unplugging and re-plugging in and nothing happened. Replaced all the filters and still it wouldh't start. So I brought it downstairs and tried one more time to get it to start. it worked! Is there something wrong with the vacuum cleaner? Was it overheat


It was overheated that is why it worked downstairs after cooling off. ... Miele S548 Bagged Canister Vacuum

Keeps stopping. My Roomba Discovery says it has a full charge, but it runs for a few minutes, then stops and beeps and the status light comes on. If you press the clean button, it will start again and go for a few minutes before the same thing happens again.


Your battery isn't holding a charge ,buy a new battery ... iRobot Roomba Discovery SE Bagless Robotic Vacuum

CLEANER SWITCHES ITSELF OFF AFTER A FEW MINUTES USE. IF LEFT FOR SOME TIME, IT WILL START AGAIN FINE, THEN AFTER A FEW MINUTES MORE USE , IT WILL SWITCH OFF AGAIN.


Check all filters, if they can be washed do so, if not clean or replace. next check for a clog in the machine and in the hoses. the machine as a thermal device that if it senses an overload or getting to hot, the machine will shut itself off for safe ... Vacuums

My dyson dc 16 hand held vacume stops & starts while in use, each time you pull the trigger it will start again but then stops after a short while untill i pull the trigger again.


Cutting out can be due to a few things , motor overheating due to dirty filter, Faulty mains cable or plug..sealed type also..Faulty Switch/trigger.May need to seek pro help to fix. ... Vacuums

My Oreck XL 9100HA started smoking (white smoke) when I vacuumed. There is a burning rubber smell. How do I check/change (if appropriate) the belt? I have no User manual, nor can I locate one on the Oreck site. The bag is a new one. The vaccuum had been picking up, though not at its best strength.


It sounds like the belt has been damaged. You can get another belt from yoru local Oreck store. You can even take it in to the store to show them what happened. Purchase another belt and replace it. (It was very easy when I did this, so hopefully ... Oreck XL Ultra Bagged Upright Vacuum

Kirby Sentria Hi, I have a new Sentria & used it for the first time today. It was going fine & then I could smell smoke & it started to make a loud noise so I turned it off quickly. If I turn it on it immediately starts making the noise again & I can see it is all lit up inside like something is burning or sparking. I have checked the roller & it is moving & I have checked the fan which is moving & doesn't appear to be damaged in anyway. This product is from the US & we are in the UK & we are us


Sounds like the motor burned up. not sure if travel adapters will handle a large load like a motor, around 8 or amps. power needs in US are 110 volts ac, 60 hertz.I believe UK is 220 volts and 50 hertz. usually when a vac is brought to eu ... Kirby Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0478 seconds