Having problems with your Panasonic MC-V7720 Bagless Upright Vacuum ?

My belt is burning do I need anew belt and just align and clean brush. Motor sounds ok

Answers :

Belts start burning because they've become too worn and loose to keep a good grip on the brush and motor shaft. You do need a new one. When replacing, ensure it's in the correct position by rotating the brush a few times. Make sure you've got the correct amount of tension on it. Too loose and the belt will slip and burn out again. Too tight may cause breakage as well as excessive stress on the motor.
\015\012It's often best to allow even a simple fix to be done by a service tech.
Repair Help & Product Troubleshooting for Panasonic MC-V7720 Bagless Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My belt is burning do I need anew belt and just align and clean brush. Motor sounds ok

Belts start burning because they've become too worn and loose to keep a good grip on the brush and motor shaft. You do need a new one. When replacing, ensure it's in the correct position by rotating the brush a few times. Make sure you've got the ... Panasonic MC-V7720 Bagless Upright Vacuum

I have a Hoover SteamVac Carpet Cleaner with Clean Surge. I lent it to my mother who used it without the brush attached underneath. Now it doesn?t **** up water and the brushes don?t turn. Any idea what would?ve broken? Is there a belt that would have burned out? The motor? Anthing I could fix myself, or would I need service for this?

If you go to this URL:\015\012\015\012http://www.vacpartswarehouse.com/Hoover-F7452-s/811.htm\015\012\015\012you will an exploded view of your Hoover. By going down the pictures you will be able to see the internal parts of the unit and ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

HI, my motorized brush barely turns.It makes a hot rubber smell. I took apart and noticed the spindle the belt turns on discolored from heat. Cleaned it, but still no turning of the brush.The vac is a hoover wind tunnel. As it moved accidentally touched the belt/ spindle and burned my hand a little. Very hot in area. Bright spark from motor noted. Was careful not to touch that part!

That means that the belt is stretched and it is slipping on the motor shaft, that is why it is hot and smells like burning rubber. You need to replace the belt. Here is the correct belt you need: ... Hoover S3765-040 WindTunnel Bagless Canister Vacuum

How to disassemble the brush to empty anything that might be stuck inside of the brush? The motor seems to be overheating, all belts have been checked, all airways are clear and the filter is clean. The vacuum is vibrating and releasing a burning smell, but still sucking up dirt. There is nothing stuck on the outside of the brush, but is there a way to check inside of it to see if that is where a clog is occuring?

If there's a burning smell and the belts are fine, the problem is going to be hot wires causing the insulation to melt, or the motor going bad. Discontinue use and have it checked at a repair shop. ... Bissell 6594 PowerForce Bagless Upright Vacuum

I have a Necchi 522, an early mechanical stretch stitch machine. The timing and stitching are great, but over the past few projects I have noticed a balky tendency when I press the knee bar. After my last project the motor almost won't engage. Sometimes there is no sound, and sometimes there is a weak whirring, but no action until I push the hand wheel. I have a feeling that it is either the v belt or that the motor needs new brushes. Are either of these ideas likely, and if so, are they self

Hi,It sounds like the machine is having to work too hard. Have you cleaned and oiled your machine lately? Over time oil will harden and lint and dust will build up on the working parts in the machine causing it to drag and eventually stop ... Vacuums

My Dyson DC 15 makes a horrible noise when switched to do carpets - sounds like gravel in the motor - and then comes the burning smell. Nothing keeping the brushes from moving, and I think they are. I am concerned that it is a belt or the motor. How do I know?

... Dyson DC15 All Floors - The Ball Bagless Upright Cyclonic Vacuum

Hello, I have the BISSELL PRO STEAMER MODEL 8805-1, it's mking rattling sound near the motor, & smells like melting rubber like when the belt is burning. I need check the belt, it's OK. Thanks so much, Susan

Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 7920 ProHeat Pro-Tech Upright Wet/Dry Vacuum

I have a kenmore grab n go bagless and I need to know the exact size of the belt, I lost the manual, and I have burn several belts at the bigining of the problem the motor stops and burn the belts I open it and I think it was a little piece of plastic, that cause the problem, but when I put the new belt it looks like the motor works fine,but still burn the belt, I'm using UB-1 #5275 belt am I using the wrong one?

... Kenmore 34722 Grab-N-Go Upright Vacuum

My Bissell Model 3760-4 is not working properly. The belt has been replaced (and checked 3 times), but the brush bar does not move when the brush motor button is on. The little metal turning piece that turns the belt is turnable with one's finger when the belt is off, but when we put it all back together and turn on the vacuum, the brush bar does not go around and the burning belt smell returns. The portable part of the machine works properly. It's the brush bar. It has been cleared of hair, etc

... Bissell Lift-Off(R) Revolution(R) Turbo Upright Vacuum

I have the bissell power force bagged upright vacuum and the brush is not turning, I have replaced the belt but the brush will not move but the metal piece that is hooked to the motor that spins the belt and brush is turning but the brush won't, and the belt starts to burn

Sounds like your brush roll is seized. Remove the brush roll (see picture) and make both of the end caps spin freely. If not, replace it and you should be set. *An example of a brush roll* ... Bissell 3522 PowerForce Bagged Upright Vacuum

Noise My Dyson DC08 is making a loud, rough, vibration/noise that seems to be coming from the from the rotating brush housing. I replaced the old belt which was several years old and slipping. When I run the motor with the new belt removed the machine sounds normal. The bearings on the rotating brush seem to be running smoothly when turned by hand both when out of the brush holder and when installed in the machine. I can't find anything rubbing on the belt or rotating brush. I applied a bit o

Hi there, it's Jack at Dyson.\012I'm sorry to hear you're having difficulty with your Dyson vacuum. From your \012description, it sounds like the model number you've supplied may not be correct, \012as DC08 is a cylinder vacuum which doesn't use ... Dyson DC08 Cylinder Bagless Canister Cyclonic Vacuum

My bissell model 18Z6 has developed a loud noise and vibration when the brush is running. I have removed the brush assy and cleaned all the hair, etc but still the noise. I ran the brush motor with the belt disconnected and all seemed ok, but of course there was no load on the motor. I suspect a problem with the brush assy bearings or axle or both but I hate to just throw parts at the problem. any suggestions would be greatly appreciated.

... Bissell Vacuums

Need to open rotating brush part of vacumm as motor functioning but roller not turning...perhaps belt broken put need to get into ..inside brush box ...Need help need instruction with diagrams Thanks for help Robert

... Panasonic MC-V9638 Bagged Canister Vacuum

Stopped running My mother's Oreck vacuum sound as if there was something bogging the rotating brush down. I pulled the bottom cover off and found nothing wrapped around or restricting the brush. I tried to finish vacuuming with the problem then I turned it off to move a chair and turned it back on it would do nothing. Any suggestions as to what could be causing the vacuum to sound as if the rotating brush is being restricted from turning. There was not odor of burning as if the motor was in a bi

Orecks have a plastic fan inside and everything you pick up hits it, sometimes things can get stuck in there or break the fan locking up the motor. With the machine off, poke around where the dirt goes into the motor, behind the roller and see if you ... Oreck XL Ultra Bagged Upright Vacuum

Motor is sparking and smells like burning rubber. When it first happened I thought the vacuum had something jamming the beater bar. That was the smell it had, like when the belt gets burned. But when we turned it over, it wasn't jamming. Took off the base plate and turned it on. The motor area is sparking and it makes a weird noise (I assume that is because the motor fails and restarts). I looked for loose wires, can't find any. I believe I need some sort of part replaced, maybe even a n

From sound and description most possible is motor is burnt up sparks usually mean metal on metal either bearing or bushings went on motor if u can jiggle the shaft thats bearing if u rotate the shaft by hand and feel and or hear rough grinding the br ... Oreck Vacuums

Hi, There is a high pitched whirring sound coming from lower part of the vacuum. When I tilt it toward me (while standing in the normal vacuuming stance) the sound sometimes lessens for a minute or so. I have tried the following things: -cleaned the two sponge filters -emptied the dirt receptacle -removed the roller and cleaned it -cleaned the brushes -the belt is not ragged and does not seem floppy -checked all of the airways for clogs (including removing the wheel base) Can you help?

Your looking for some dirt stuck in some thing you didn't check yet. with the roller out and the belt out of the way run it to see if it still makes the noise. if it does then you looking at the impeller or the motor bearing themselfs those bearin ... Bissell 3750 Lift Off Bagless Upright Vacuum

Dyson DC04 is making a grinding sound & smells of burning. Hi. I have been told that the above is due to the carbon motor brushes burning out. The brush at the bottom still turns ok. I have bought 2 new carbon brushes & wondered how I would go about replacing them. Any help would be much apprecieated!

Hi there SmartAlec from NelsonVacuums.com.au here, this is not a repair for the faint hearted. First i am assuming you are not using a clutch model - with a selector for ca ... Vacuums

Hoover windtunnel U6425-900 the brush roll is not turning. Both belts are in good shape, I cleaned the brush roll and it is free of debris, the setting is on carpet and the brush roll still will not turn. There is a "burning rubber" smell when you attempt to push the vaacum forward a few times. The small belt does not seem to be pulling properly but appears to be in good shape.

... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

My older Dyson DC14 (the purple one) early model with a clutch on the beater bar belt needs a clutch replacement. The bar has been cleaned and there are no worn or damaged parts so I conclude that the clutch at the motor end of the belt needs to be replaced. I can find the part online but no instructions on how to disassemble the vacuum to get to and replace it. Dysons only advice is to give me the address and phone of the nearest service center. Can you help me?

Have a look at www.dysonmedic.com which has some very useful info on dismantling and repairing Dysons.\015\012\015\012Although this site doesnt actually cover the DC1 ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

Hi, I have a Dyson DC04, (silver/lime) making ear popping screams! Does not happen all the time, and more noticeable when it is pulled back.The suctions not a problem and no funny smells or strange noises from the motor. Ive taken the base plate off and the belt and brush bar seem fine, but when I turn the belt, it seems to be the motor spindle thats squeaking, almost as if it need oiling, any help please

... Vacuums

I have a Filter Queen Majestic 360 and am having problems with the powerhead. There is a loud rattling noise in the powerhead, especially when I vacuum thicker carpet. I have replaced the motor, roller brush, and belt, but the rattling remains. It sounds like it is coming from the roller brush area,and when I turn the powerhead over, it rolls free and sounds fine. Any thoughts?

Hi there, as per your information i guess its a problem of power transformer. He can't supply the proper power in the motor & thats why the noise will come from the transformer. Thanks & waiting for your feedback. ... Filter Queen Majestic Canister Vacuum

I have recently replaced the belt and filters. The belt is in the correct position and the rotating brush moves freely. The motor is very loud. It still vacumns but I'm afraid the motor will burn up.

Does it sound different than it did before you made the repairs to it or does it sound the same. Just so you know some of the upright vacuums on the market today sound like a jet airplane landing in your living room.Ca ... Bissell 6594 PowerForce Bagless Upright Vacuum

Vorwerk ET 340 - been great but now noticing strong burning smell after vacuuming some hair from the bathroom. Bag is nearly empty. Gave it a rest then unscrewed the cover housing the motor and all looks clean (dust is sucked up the pipe and doesn't appear to get near the motor). When I restarted it, burning smell still there. Are there any filters that might need changing? What could be causing the smell? Could the hair have gotten caught somewhere? Thanks.

Jessica,\015\012\015\012Try changing the dirt bag.\015\012Check if the motor gets hot after operation. You can come to check it by touching outside the motor housing. If it is hot or just warm.\015\012Is the smell of burning hair or something e ... Vacuums

I have a NUTONE central vac, when I turn on the power, It sounds like its grinding glass and doesnt suction. Could it be that broken glass got caught in the motor and all I need to do is clean it, or is this the sound of a failed motor?

More likely it's something in the fan. However, I suggest taking it to a vacuum repair shop to make sure. Something could have got into the fan system and is making a racket, but the motor itself won't crunch up glass. ... Electrolux Central Vacuum

Now that I just fixed my Lux Legacy canister vacuum, I need help on my other Electrolux Regency Series upright! The vacuum works fine but the rotating brush does not work and the brush motor does not turn on. Tried cleaning the brush and hitting hte reset button to no avail. This upright has a triple setting switch and I checked the each of the wires seem to be attached. Tried rotating the brush by hand and it would not budge. Was going to "encourage" the brush to turn with a set of articula

There are a couple rectangular holes on the bottom of the power nozzle, beside the wheels. These have tabs in them that need released with a standard screwdriver. \015\012 ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 2.1553 seconds