Having problems with your Panasonic MC-V9620 Canister Vacuum ?

Need to open motor compartment

\015 I can't see any screws where i could check or replace the motor. an electric smell. can't open the motor compartment.\015\012please help\015\012thanks\015

Answers :

Use a flat blade screwdriver, The dusy compartemnt door will come off by pushing it back, it just pops out. Then the rear top cover is held on by a tab, one in each corner. Put the flat blat in the slot at the bottom of the cover and work it until it pops loose. Then there are 2 screws to tak out to remove the cover over the motor and cord reel asm. But now you can get to the motor.
Repair Help & Product Troubleshooting for Panasonic MC-V9620 Canister Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Problem with motor; need to open the motor compartment


This may help. My Kenmore is ten years old. I found two screws under the hinges of the cover to the tool accessory compartment. Remove cover screws are in the corners. The other two I found are under the cord return foot pad. Pad pops off by pry ... Kenmore 23612 Progressive PowerMate Bagged Canister Vacuum

Need to open motor compartment


Use a flat blade screwdriver, The dusy compartemnt door will come off by pushing it back, it just pops out. Then the rear top cover is held on by a tab, one in each corner. Put the flat blat in the slot at the bottom of the cover and work it until ... Panasonic MC-V9620 Canister Vacuum

Miele Cat & Dog vacuum gets VERY hot and is VERY loud. Hose has no restrictions and I have changed the dust compartment (motor) filter and the exhaust filter. It still gets hot when I run it with the top open and all filters removed, so I'm guessing the problem is with the motor. Should I be going into the motor compartment? If so, what am I looking for?


Hi\015\012\015\012The fact that it gets very hot could be due to a number of issues.,but the fact that it started making a very loud noise at the same time suggests that there might be more problems maybe brushes etc.\015\012\ ... Miele S514 Solaris Bagged Canister Vacuum

Need to open rotating brush part of vacumm as motor functioning but roller not turning...perhaps belt broken put need to get into ..inside brush box ...Need help need instruction with diagrams Thanks for help Robert


... Panasonic MC-V9638 Bagged Canister Vacuum

Need technical help for my miele s2180 momentum canister vacuum .Bought a display open box at fure shop..Came with a filter bag..there are no tears in the bag...Perhaps they put the wrong bag..Anyway after 30 minutes of use..The motor stopped working ..so I opened up the unit only to see,.the dirt was everywhere inside the vacuum...only a little was in the bag itself..can you hepl..Dave


... Vacuums

What type of tool do I need to open up the bottom of the Cuisinart DBG-550BCHWS? My on/off and digital clock lights are flashing when I plug the coffee maker in and the maker doesn't not work. I have tried opening and re-closing all compartment doors. Thanks for your help.


Screws are Torqux Tamper-proof/Safety screws size T-10. It's a Torqux \015\012screw with a raised middle requiring a special Torqux wrench. You can buy a T-Handle set at Sears for $35.\015\012\015\012 ... Vacuums

How to open motor compartment to check motor on Kenmore canister vacume cleaner model 8120


... Kenmore Vacuums

I have a kenmore grab n go bagless and I need to know the exact size of the belt, I lost the manual, and I have burn several belts at the bigining of the problem the motor stops and burn the belts I open it and I think it was a little piece of plastic, that cause the problem, but when I put the new belt it looks like the motor works fine,but still burn the belt, I'm using UB-1 #5275 belt am I using the wrong one?


... Kenmore 34722 Grab-N-Go Upright Vacuum

How to remove the " button cord rewind " from the kenmore progressive model 116-28712790 ?? I need to get to the screw below to open up to get to the motor.


I found the problem... screws on top under the cord rewind bar ... Vacuums

How do i open a sanyo sc-b555 to get to the motor. i need to remove the casing but i can not find all the screws?


... Sanyo Vacuums

How to open the motor housing.


Pls i want put music in my phone but its not possible i need ur help ... VAX Appliances 2000 Canister Vacuum

Bissell proheat 2x 9200 series carpet cleaner. I need to remove the Brush Drive motor. However, this series has the gear end of the motor shaft poking out a hole on the left hand side. I removed the retaining washer and pin from the gear shaft. I need to get the gear off of the shaft in order to remove the motor. It's not budging. How do I remove the gear so I can pull the motor out of the unit? Thanks .


Chap, I wish someone had answered this. I'm having the exact same issue. ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

OPENING CANISTER UP TO SEE IF BEARINGS OR MOTOR IS GONE


You really don't want to get into the vacuum. After you get in, there's not much that you can do other than look. If you really want to get in, there are two strips,one on each side of the cleaner under the rubber bumpers. The strips have to be remov ... Electrolux UltraLux 2000 Bagged Canister Vacuum

Need to replace motor on a Simplicity upright vacuum and need help with the wiring the new motor. New motor is different from old one.


You might not have the right motor. Take the old one with you because it should go right back in as easy it was to remove. ... Vacuums

Compartment lid pops open when vacuum turned on


You will wish to call either the retailer you purchased it from, or call Hoover at \015\0121.800.944.9200 ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Opening Miele S28i Vacuum cleaner


If it is similiar to the white star you may find the instructions here useful: http://www.sannerud.com/house/miele.htmlhope so ... Miele S251i Plus Bagged Canister Vacuum

I have my vacume electrical cord tangled inside and disconnected (I can see the open end of the connection from the power cord collector wheel! I need to take the vacume apart so get access to the wire inside. I need to know if there is something else to open other than the 4 screws. Your help is highly appreciated in advance.


Since you did not provide a model number for your vacuum, it is difficult to provide any precise directions regarding disassembly.\015\012\015\012However, most vacuum cleaners are fairly straightforward machines, and as long as you unplug ... Vacuums

Kirby Vacuum Hi Bruce, In my opinion, yes the Kirby would be worth it, as long as you are not replacing the motor. The switch would be the most expensive part besides the motor that would need to be replaced. The switch costs USD 49.99, the cord is roughly $39.99, and the carbon brushes are $29.99. I can easily walk you through any of these repairs should you need help. Kirby's are great vacuum cleaners, that usually last 30+ years. Brand new these machines sell in the US for $1600 or more,


You can get better prices from Goodvac.com ... Kirby Generation 3 Bagged Upright Vacuum

No power to vacuum motor. Switch need to replace.


See my response to "posted by bigbadben on Oct 07, 2007".The cover that I referred to in my answer is a small plastic plate that covers the 'live' electrical bayonets between the electrical cord rewind spool and the motor. I did not make ... Electrolux UltraLux 2000 Bagged Canister Vacuum

Miele S5000 (revolution 5000) vacuum cleaner - How do I open the casing? When the power button on the handle is pressed the green power-level lights on the handle light, but the motor sounds like it gives a little 'jump' but nothing more. The orange power light on the body also dims. I assume the motor or fan is jammed, but I can't open the body to find out. I've taken out to screws inside near either end of the handle, but to no apparent effect. I'm assuming the body is held together by plastic


... Vacuums

I need to change the motor in a vax 6131 but i don't know how to get into it to get the change it? I also need to get into the motor assembly housing to change a part but can't see how it comes apart!!


On the handle there is one small pozidrive screw, remove and orange panel comes away revealing powercable securing bar. Remove 2 screws and this reveals a 10mm headed bolt. Under label on top of handle there is another small pozzi screw, undo t ... Vacuums

Need to replace power cord and can't find how to open canister to replace


I had the same problem and could not find the other screws. You need to pry off the power cord retraction button, you will find two more screws under there. It's pretty easy after that!!!! ... Kenmore 22612 Bagged Canister Vacuum

My electrolux epic 6500sr vacuum has a seized motor. How do I acess the motor to service or change it? There are no obvious screws or clips to open the motor outer case


... Vacuums

I have a Eureka Boss Model 411... I need to know where the reset button is for the suction motor. The canister was clogged on the backside, I didn't see it and the suction motor shut off. I have cleared the obstruction, but don't know where the reset is for that motor. I know how to reset the brush head motor.


If your vacuum motor overheats, it will stop working. it will start working again once it cools. ... Eureka 411A Upright Vacuum

Replacing the Oreck vacuum cleaner motor with a generic Ametek motor, the wiring terminal are different and I need an electric diagram


... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0713 seconds