Having problems with your Panasonic Vacuums ?

Panasonic MC-E450 vacuum cleaner wiring connection access

\015 Trying to access the electrical box section of the above. Can see three screws in total, (2 inside at front and one at rear) but panel still does not seem to want to budge. There is an obvious simple wiring connection failure, but access is proving difficult. Any advice welcome\015

Answers :

Disconnect from power first!!
Undo the three screws.
Tap the base of the handle assembly from the front and it will slide back so it can be removed
With the handle removed, pivot up the bottom of the electrical box cover and it will unclip at the top edge.
Repair Help & Product Troubleshooting for Panasonic Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Panasonic MC-E450 vacuum cleaner wiring connection access


Disconnect from power first!!Undo the three screws.Tap the base of the handle assembly from the front and it will slide back so it can be removedWith the handle removed, pivot up the bottom of the electrical box cover and it will un ... Panasonic Vacuums

TRYING TO REPLACE THE PLUG ON An ELECTROLUX Z5915 1600W vacuum cleaner, IT HAS TWO WIRES from the cord.....BROWN AND BLUE.....BUT 3 POSSIBLE CONNECTIONS ON THE PLUG NOTED N, L and the earth connection.


... Electrolux Vacuums

I own an Oreck 2310RS upright vacuum cleaner. The cord is too short for my needs. The cord I need is a two wire 25 to 30 foot cord. Where can I buy this vacuum cord and how do I connect it? Thanks, Don


You can buy one at a oreck store but i would tell you to use an extention cord ... Oreck XL2200 Bagged Upright Vacuum

Does the blue wire connect to the black or purple wire in a dyson dc05 vacuum cleaner (australia)


Black with bluered with brown ... Dyson DC05 Cylinder Bagless Canister Cyclonic Vacuum

Just bought a Rainbow vacuum cleaner on/off switch and I need to know how to wire it since the original one has six connections and the new switch has only four. I'd appreciate your help. Thank


Call out tech. support number at 800-640-2033, and if you purchased from us, we give free phone support.....www.rainvac.com ... Vacuums

I have a Panasonic MCE6003 vacuum cleaner. I regretfully leant it to a neighbour and it came back full of dog hair and keeps cutting out. I cleaned out the dust container and the main filter but it still kept cutting out after 5 minutes. I decided to unscrew the part with the motor and wash the filter inside.It was all going well until a large rubber washer bit, a piece that looks like the thermostat and a little white button attached to two black wires fell out and now I have no idea how to put


... Panasonic Vacuums

The 10 amp thermal fuse on my Panasonic MC-E468 vacuum cleaner has blown. Unfortunately the red ink has worn off exactly where the temperature rating is printed so even with a magnifying glass cannot make out the exact replacement fuse to buy. Can anyone shed any light. I know you can buy the complete thermal fuse and wiring from currys partmaster but with delivery would cost about 20 pounds as opposed to 69 pence for the fuse itself. Thanks Mark Roberts


It appears the fuse is not available separately. Standard retail price for the complete unit is £9.00 including VAT. We can supply at that price plus postage and packing at cost, which would probably be no more than £2.50.  If this i ... Vacuums

Vacuum cleaner We have a panasonic MC-E47electronic which seems dead. It has a speed control which we nearly always had on full anyway. Have tested continuity through plug, flex and on/off switch and all OK. from then is open circuit through speed control which consist of slide rheostat and mystery small green box (2cm x 2cm x 1cm approx). Across motor there is negligable resistance. Machine is quite old and not worth paying out loads on poarts if it is safe to bypass speed control and connect


Yes it is safe, but i would make a switch? ... Vacuums

Access to panasonic mc e450 electrical supply panel


Disconnect poweRemove three screwsTap base of handle from front - it will then slide backremove handlePivot bottom of cover over electrical box up and it will unclip from the top edge. ... Hoover Vacuums

Panasonic MC E468 vacuum cleaner power cable replacement


... Vacuums

Panasonic MC-E468 vacuum cleaner manual


... Vacuums

I have a motor for the Bissell 3750 power head with a black and brown wire, which wire is connected to what?? The old motor just had 2 black wires. There is a blue wire coming from the vacuum and blue wire coming from the light that are together, and a blue wire coming from the light and a black wire that are together. What does the blue and brown wire coming from the motor connect too? Thanks


... Bissell 3750 Lift Off Bagless Upright Vacuum

Panasonic MC-UG729 vacuum cleaner overheats - Panasonic MC-UG729 Platinum Quiet Force Upright Vacuum Cleaner


... Panasonic MC-UG729 Platinum Quiet Force Upright Vacuum Cleaner

The last time the vacuum cleaner was used the outlet sparked causing it to smoke when turning on vacuum cleaner. I replaced the outlet and plugged it in and things seemed o.k. Today I turned on the vacuum, it stayed on for a mili second and went off. I checked the switch on the vacuum and it showed voltage coming and going, but would not turn on again. I checked all the wires in the area of the switch all seemed o.k. I thought maybe there might be a short in the cord. When I went to plug


... Sharp Twin Energy EC-12TWT4 Bagged Upright Vacuum

Meile Solaris. Power cord connection faulty. Unit powers on/off when cord is being retracted/pulled out. Maybe a break in wire close to connection point in vacuum. Or, the connection point itself is loose? The problem likely resulted from trying to use vacuum at furthest extent of cord.


Cord reel likely needs to be tightened. requirs disassembly and large washers installed to keep reel connections tight. Jim ... Vacuums

I have a dyson animal dc17 vacuum and it totally died. Now I can't figure out which wires go where when I install my new motor. (motor #: 160906G) Do you happen to know where the various color wires go or a place I can see a diagram of the motor with wires attached? I should have taken a photo of it before tearing out the old motor. I don't know where to connect the three coming out from the upright portion of the machine and the red seems to go to a switch (?) and there is a black (connected t


... Vacuums

I have a Kirby Heritage 84. Great condition except the part that connects the innerbag is missing. I don't even know what it is called. I can open the vacuum cleaner bottom and see that the part is missing. It should be oval where it connects to the vacuum and then extend into the cloth bag. PLEASE HELP!


The Heritage 84 had two different bag assemblies available. One is a dump-out bag. The dirt simply dumps through the bottom. The other is the bagged style which has a full length zipper to open it. Inside it should contain a "bag fill tube", and a to ... Kirby Heritage II Vacuum

Panasonic vacuum cleaner overheats - Panasonic Vacuums


... Panasonic Vacuums

I have an older Oreck XL vacuum that sounds like it is running twice as fast as it should. I disassembled the entire vacuum, including disconnecting the motor wires, to clean out the hair, string, and other things. When I put everything back and connected all the wires, everything appears to work, including the light. The only problem is, it sounds extremely loud like the motor is running too fast. The model number is: XL3610HH Ser. No. 3610HHXA039740-6 I do not have as electrical diagram to see


... Oreck XL Ultra Bagged Upright Vacuum

Panasonic upright vacuum brushes dont turn - Panasonic Bagless Upright Vacuum Cleaner MCUL915


This may be too obvious, but do you have the Carpet switch turned on (bottom left of vac). Agitator brush does not go around if Floor/Tools is switched on, ... Panasonic Bagless Upright Vacuum Cleaner MCUL915

My bissell 3595-2 vacuum cleaner started turning off the power automatically. Now I can not get it to turn on. This vacuum cleaner is still in real good condition, as I have hardly used it. Please advise what could be wrong. I was thinking maybe a loose connection with the on-off switc.


... Bissell Vacuums

Royal vacuum cleaner model 4600 wiring diagram I have a Royal Vacumm Power Tank Model 4600. I replaced the switch (6 wire - 3 position) that is on the tank. One side of the switch control just the blower. The other side control the blower and the POWER head - wand with a variable control speed. The middkle position is off. After I installed the swith, the power head - wand is powered in either position. There are three wires comming out of the wand: White, Red and Black. I guess I wired somethin


... Vacuums

Local vacuum repair shop replaced motor in Oreck XL 2600HH and now the lights blow out immediately upon powering up the machine. I believe the wires for the lights were mis-wired to the terminal blades on the motor housing. is there a wiring diagram available to properly connect the wires to the motor housing?


Hello. if this repair just occurred return this vacuum to that repair shop as they owe you a valid repair. I agree that they caused the lights blowing out problem. They must repair this for no charge. If you work on it yourself they will blame yo ... Oreck XL2600 Vacuum

HOW TO REMOVE BACK COVER ON A PANASONIC VACUUM CLEANER MC-E554UK


... Panasonic Vacuums

Panasonic vacuum cleaner MC E554


Wish you had listed your model number, they are all different you know, that wire you refer to I have seen on some models and it is only a belt guide. Should be a slot that it fits into. ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0892 seconds