Having problems with your Panasonic Vacuums ?

The retracktable power cord on my Panasonic MC-E7103K is jammed inside the machine. Does anyone know how I remove the cover after removing the two visible screws? Brian

\015 The two visible screws are at the rear of the machine and hold the red and grey halves of the machine together. I need to seperate the two halves to get at the cable.\015

Answers :

Repair Help & Product Troubleshooting for Panasonic Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

The retracktable power cord on my Panasonic MC-E7103K is jammed inside the machine. Does anyone know how I remove the cover after removing the two visible screws? Brian


... Panasonic Vacuums

I have a Panasonic MCV7515 UPRIGHT VACUUM and need to remove the cowling that covers the brushes to clean the hair out of the bearings, but it isn't clear how that can be done without a crowbar or sledgehammer. Removing all the visible screws makes the hindmost part loose, but not the front half. Also, is there an easy way to replace the belt?


... Panasonic MC-V7515 Bagged Upright Vacuum

I can't seem to get the belt cover off of my Kenmore Progressive 400. There are two buttons that say above "belt and bulb change" but the buttons do not move. Do you know how I can remove so I can put a new belt on? Thank you!


You have to take off the top of the power nozzel that has the light lense. There are two pressure locks,one on each side. Use a screw driver to release. You will see the screws.Take the two screws out and on some models, there are two pressure locks ... Kenmore 23612 Progressive PowerMate Bagged Canister Vacuum

The battery will not charge in the sweeper. I can remove the battery and wire it to the power supply for charging and it will charge up and run the sweeper. So the power supply and the battery are both good. Obviously there is a circuit failure in the on board charging control. Anyone know a fix or a likely faulty component? I had a shark handheld about 8 years ago and it developed the same problem. I examined the little circuit board inside but saw no visible indications that would isolate t


... Euro-Pro Cordless Bagless Upright Sweeper - Blue/Gray

Agitator belt failed in my Hoover F5853-900 Steam Vacuum Cleaner. But can not remove bottom Cover .. have removed top cover and two screws from the bottom Cover. The smaller Cover is glued to the large Bottom Cover. Need help.


Hello,Unscrew the plate. check if there is any screws at the bottom, if none, exact little pressure to pull out the bottom cover. At this \015\012point you should be able to see the broken drive belt along with the two\015\012 drive bars ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

Kenmore Model 116 Cannister Vacuum.Trying to get into motor area. Think belt is worn out. I have removed the front two screws under the hinged cover, but can not remove cover over motor.. Still attached at rear. No evidence of any more screws to remove.


Under the cordwinder actuator button, are your other two screws. To remove this cover, take a flat tipped screwdriver and , very carefully, find the "tabs" (there are two) both on the front section under the button. Then, Carefully, press them in a ... Vacuums

Suction Cover The suction cover of my Eureka Deep Steam 2575A is broken - the tabs snapped off of the cover so I am unable to screw the suction cover back on. I need to purchase a new suction cover but can't find one anywhere. Anyone know what I can do? thanks


The exact same thing happened to me. i just called and ordered it from eureka. the number is 1-800-282-2886. the cover cost 13.07 and the s ... Eureka 2576A Steam Vacuum

I need to remove the top cover from a Wertheim w4030, I have removed all screws that I can get at. I have notice a further 3 in places that is not possible to access. It looks as though the two buttons on the top if removed will provide the solution but I don't want to break anything by forcing something that is not supposed to be done. Can you help?


... Vacuums

How do I remove the battery in a Dustbuster chv1400 for replacement? I have removed the two screws and removed the cover, but I'm unable to figure out the retaining clips for the battery. Of course I don't want to break the clips.


That model looks similar to my DB200. Instead of the screws, the underside has a latch/panel that you remove. Place a screwdriver in the two slot-like holes that face each other (one at a time) and the 'door' should pop out. Mine was a little stiff ... Black & Decker Vacuums

I have a samsung SC7800 (smart wing system) vacuum cleaner. I think the impeller is jamed with sawdust. I have removed the part than holds the removable filter, but can't see how to remove the reat of the top case to access to impeller housing. Does anyone know how to do this or where I can view a repair manual for this model?


Unfortunately these tend to break frequently.... You might be able to get a wiring diagram at www.wize.com Good Luck!! ... Vacuums

Cover knobs How do you remove the two plastic knobs on the cover for bare or carpet and carpet heighth to get the cover off?


You don't have to remove those knobs to get the cover off. Just 2 screws from the bottom, then on each side you will notice a slot from the bottom, use a screwdriver, insert in the slot, and pry out to release the catches and the top cover will come ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Removing motor cover on Panasonic canister vacuum


... Panasonic Vacuums

I can't find the 4 screws to get to the belt on a dirt devil 22.0 Fx. The bottom of the vaccuum says " remove four screws from bottom of nozzle then lift top nozzle cover off", where are these screws, I can only find two, and which is the top nozzle cover?


... Dirt Devil Vision Turbo W/Bonus Upright Vacuum Vacuum

Faithful Sebo X1 upright, about 12 years old, stopped working today. I replaced old with new dust bag, checked all dust paths were clear, checked main brush was clear/clean, and drive spindle rotated OK with fingers. When power switched on, the two red indicators briefly flash on then off, but nothing more happens, motor does not start - even with power reaching machine. Tried removing all consumables, refitting and turning on a few times to reset, no joy. Removed base cover, both belts were i


At 12 years, this vacuum has had a good long life. I suspect the motor is shot, but it could be due to faulty wiring and connections. A bad switch, break in the power cord, and worn brushes in the motor are other causes.\015\012I recommend ta ... Sebo Automatic X1 Bagged Upright Vacuum

I am getting very little suction from the motor. The hose is clear, the bag new. When I open the bag cover, plug the hose in and turn the vacuum on, there is next to no suction from the motor. What do you think is wrong? How do I remove the cord retractor to get to the two screws that hold the back of the canopy cover?


Your problem is probably is you don't have a proper seal in your chasis. A vacuum has to be sealed tight or the air will leak out and the seal broken. Check around the whole body after the bag is in and check for any airflow noise. I could help more ... Vacuums

OUR DYSON 07 SWEEPER HAS VERY LITTLE Vacuum, have cleaned all filters and hoses, on line troubleshooting has said to check soleplate being on correctly, we have done this, still does not have good vacuum, belts are covered by a housing, the video that shows the changing of the belt is not the same, I need to know how to remove the cover to check both belts and any help in gaining the vacuum


This video shows you everything you need to know ... Vacuums

We have a dyson dc14 and the beater bar stopped turning, we cleaned the bar off and checked the belt and it's not broken, I know I called Dyson a year or two ago and they told me how to reset the beater bar motor but I don't remember exactly what I did, anyone know the answer to this??? thanks in advance....


Hi its Darran at Dyson.Check that the brush control dial is in the centre position when the machine is locked upright. When you release the head and pull the handle back this dial should mopve forward to the on position. Once here, the ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

How do you dismantle a Panasonic MC-3920 vacuum cleaner? I have removed the 4 screws at the top but still doesn't come apart and one got ideas. How do you remove the blue top cover ?


... Panasonic MC-3900 Bagged Canister Vacuum

Hoover power drive u6311 - How do u change switch? Does anyone have any idea how to remove the on and off switch, when I tap on the housing the motot and light goes on and off. Also does somebody have a exploded view of this model. also does anyone know the part number of the switch.


The swrtch is located in the bottom section of the motor. When the swtcih goes out it time to repalce the unit. The swtich is part of the motor. The switch rod run all the way down the body to the swtich located in the motor. ... Hoover U6311-930 Power Drive Bagged Upright Vacuum

Hover F7452-900 My brushes are not turning. I have taken the tanks off to check the switch that changes from carpet to hard terrain to Ceramic tile.I noticed that there is a spring that has came off. I tried to disassemble the top half (nose) of the cleaner but I have came to a stand still. I cannot figure out how to remove the cover so I can figure out where the spring should be attached. I have removed all the screws that are visible and it still won't budge. It is loose but on the back side o


Regarding the brushes not turning:\015\012\015\012Your filter may need to be cleaned. It is located behind your brushes. With your tanks removed and the cleaner unplugged; tilt your cleaner back. The filter screen located behind your b ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

Need to remove bottom cover of Panasonic MCV7314 vacuum to see if the belt is broken. I can't figure out how to remove and can't find a manual online.


I did a search for the manual for that model and found a pdf file online that had instructions and pictures. It was still slightly different and hard to get off. I took out two screws and then held in two side "clips" and wrestled it off. I dont t ... Panasonic Vacuums

Brushes stopped The brushes stopped turning while using the cleaner. I removed the brushes to see if the spindle was broken, it wasn't. I then removed the top plastic cover and checked the switch that engages the brushes; it didn't seem to be moving correctly. There's one spring on the switch - should there be two? Or do you think something has broken on the inside? Thanks for any help


Most likely the turbine is bad, it may just be clogged up, you can take it apart and clean it out real good. That may work, but it may not. Sometimes it is best to replace the turbine. ... Hoover F7431-900 SteamVac Vacuum

How do i remove the reel cover for my SEARS canister model 116312690 vacuum cleaner. we are unable to move the cord forward or back. We have found two screws, but are still unable to remove the cove


... Kenmore Vacuums

SQ10 rdf Wap industrial vac. Removed two screws holding cover on. Cover won't come off.


... Wap Vacuums

HOW TO REMOVE BACK COVER ON A PANASONIC VACUUM CLEANER MC-E554UK


... Panasonic Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0496 seconds