Having problems with your Philips Vacuums ?

PHILIPS MOBILO PLUS (vacuum)- How to remove motor cover?

\015 Hi,i have a philips mobilo + and i want to access the motor but i cant remove the plastic cover! I cant leave w/o it, please HELP!Thanks in advance\015

Answers :

I found a solution. At least on my Mobilo HR8572. There are two tabs on the top plastic parts that hold on to the bottom plastic part. These tabs are located above the wheels, if you look closely you will see thicker grey plastic. You have to put a big screwdriver under the top plastic part and move it outward. The tabs are 6mm thick so you have to bend it out considerably. It then pops open. Works a treat and all the motor and electrical components are easily accessible using a simple star driver
Repair Help & Product Troubleshooting for Philips Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

PHILIPS MOBILO PLUS (vacuum)- How to remove motor cover?


I found a solution. At least on my Mobilo HR8572. There are two tabs on the top plastic parts that hold on to the bottom plastic part. These tabs are located above the wheels, if you look closely you will see thicker grey plastic. You have to put a b ... Philips Vacuums

PHILIPS MOBILO PLUS 8566 (vacuum)- How to remove motor cover? I have to reach to the fans but I don'r find how to do Please I need a help [email protected] [email protected]


... Vacuums

I am getting very little suction from the motor. The hose is clear, the bag new. When I open the bag cover, plug the hose in and turn the vacuum on, there is next to no suction from the motor. What do you think is wrong? How do I remove the cord retractor to get to the two screws that hold the back of the canopy cover?


Your problem is probably is you don't have a proper seal in your chasis. A vacuum has to be sealed tight or the air will leak out and the seal broken. Check around the whole body after the bag is in and check for any airflow noise. I could help more ... Vacuums

Old Sanyo 1500 watt "Power Control" vacuum cleaner. I need to remove the plastic covers that are attached to the on/off switch and the power cord recoil. This will allow me to remove the retaining screws for the upper motor cowling. The motor and wiring is clogged with wood dust and I want to blow the dust out using compressed air.


... Sanyo Vacuums

Removing kenmore vacuum Canister motor cover model 116-27312790


What you need to do is take it apart and look for any carpet peices dug up in there preventing the motor to spin. Also go look for another filter for it and if you google it you can probably get instructions or if you still have the book. ... Kenmore 25512/ 25513 Progressive Canister Vacuum

Removing motor cover on Panasonic canister vacuum


... Panasonic Vacuums

Removing vacuum cleaner motor philips fc - Vacuums


... Vacuums

I have a Sears Upright vacuum cleaner, model 116.35922500. The vacuum wasn't picking up. I discovered a clog in the nozzle hose. I attempted to remove the cover of the brush unit to clear the clog. I was unable to remove the cover completely, but was able to clear the clog. My problem now is that I cannot replace the cover correctly. Is there a way to remove this cover? Thanks, Elizabeth


When you tried to remove the cover did you have to put a little force on it to get to the clog ... Vacuums

I am trying to take my philips vision 8731 vacuum cleaner apart because a heap of c*** got sucked into the motor when the bag was not put in correctly. I have removed all visible screws but cannot for the life of me find how the wheel end comes apart. any tips?


Generic problem for all Vacuums\015\012I am trying to take\015\012I am trying to take my Philips vision 8731 vacuum cleaner apart because a heap of c*** got sucked into the motor when the bag ... Vacuums

Need manual for Eureka Powerline Plus Model 9730 Type A - missing "door" that covers tool access port on body of upright motor...any ideas? This causes dirt to fly out unless tool hose is placed in "port"--don't always want to use tools, just main vacuum.


I found it at www.vacpartswarehouse.com for $4.79 + sh ... Eureka Powerline LiteSpeed 5845 Upright Vacuum

I have an older Kenmore vacuum cleaner - Model #3285590C, Serial #DG4117817. I can't seem to figure out how to get the motor cover off. 2 bolts in the front have been removed but the back has no visible bindings. It seems to be held from inside the compartment! Whats the catch here!


... Kenmore Vacuums

I need to replace the agitator belt on a Hoover Elite U4465-9 upright vacuum cleaner. I have removed the bottom cover, but there is no access to the motor spindle to loop the belt around. How do I do this?


... Vacuums

Kenmore Model 116 Cannister Vacuum.Trying to get into motor area. Think belt is worn out. I have removed the front two screws under the hinged cover, but can not remove cover over motor.. Still attached at rear. No evidence of any more screws to remove.


Under the cordwinder actuator button, are your other two screws. To remove this cover, take a flat tipped screwdriver and , very carefully, find the "tabs" (there are two) both on the front section under the button. Then, Carefully, press them in a ... Vacuums

Bad Motor I have purchased two of the Kenmore direct drive beltless systems with Progressive systems. The first died after a year, the vacuum motor start making a grinding noies. I pulled the side HEPA filter and could see a fine coating of graphite like dust. Took it to a vacuum repair shop. They said the brushes were going and thus the motor was shot. I liked the vacuum and bought a second, 1 year later the motor is making a slight noise that and removing the HEPA filter I find a slight metall


That dust is from the carbon brushes on the motor. You may need to check them, and also clean out the motor compartment. A slight noise could be a motor bearing starting to go. Does the smell like rubber or electrical. If rubber, then the belt h ... Vacuums

Samsung Quiet Storm Canister Vacuum VAC-9049 The motor will not run. Power is on to the motorized rug tool. How can I remove the upper housing to get access to the motor? I have removed the six visible screws, but the housing is restrained at the rear. I suspect there are additional screws under the power switch and cord retractor assembly, but I cannot remove that either. HELP!


Hi Daltm,\015\012Thank you for contacting Fixya. This is Anil.\015\012I understand that you need assistance n opening the Samsung Vaccum VAC-9049 motor. I will be glad to help you with it.\015\012Please go through ... Samsung Quiet Storm 9048R Bagged Canister Vacuum

Agitator belt failed in my Hoover F5853-900 Steam Vacuum Cleaner. But can not remove bottom Cover .. have removed top cover and two screws from the bottom Cover. The smaller Cover is glued to the large Bottom Cover. Need help.


Hello,Unscrew the plate. check if there is any screws at the bottom, if none, exact little pressure to pull out the bottom cover. At this \015\012point you should be able to see the broken drive belt along with the two\015\012 drive bars ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

How to remove the motor cover?


There are 2 screw under the removable outlet cover and 2 more under the shiny label under the booster slider. Pick off the label to find them. ... Electrolux Vacuums

I have a Necchi LYdia 3 machine type 544 The motor was overheating and I removed the bottom cover and examined the motor .It looked fine and ran well. It worked OK for a time and then got hot.I was able to partially remove the motor for inspection.I found that the cooling impeller was not secured to the shaft,I tightened the set screws and reinstalled the motor. In process of getting the drive belt back on I turned the wheel that extends out of the case to index the screw that attaches the bobb


Good day!Please try to re align the motor position.You have to do is repeat the procedure that you take to remove the motor and double check the alignment because all motor in misalignment is very hard to turn.And ... Vacuums

OUR DYSON 07 SWEEPER HAS VERY LITTLE Vacuum, have cleaned all filters and hoses, on line troubleshooting has said to check soleplate being on correctly, we have done this, still does not have good vacuum, belts are covered by a housing, the video that shows the changing of the belt is not the same, I need to know how to remove the cover to check both belts and any help in gaining the vacuum


This video shows you everything you need to know ... Vacuums

Dead motor? My 8 year old Miele S251i has worked fine, until I was recently vacuuming and moved the plug from one outlet to another. When I restarted the vacuum, it made rrrrr.....rrrrrr....rrrrr noises and smelled like something was burning. I turned it off, and it's shown no signs of life since. Sound like a motor problem? I've taken the cover off and looked at the cord and seen the motor, nothing looks obviously wrong, but I'm also not mechanical.


... Miele S251 Flamenco II Bagged Canister Vacuum

How do I remove a motor from a Dyson DC04? The bottom plastic cover can be removed by unsrewing the tork screws but the cover beneath the filter won't come off


I can't say exactly how to do this, but when you can't find the screws to take something apart, they are usually hidden by something else. You did good looking under the bottom cover, but what you're looking for is elsewhere. If there is a seam or ... Vacuums

I have a new bag in, checked the hoses for clogs have the motor cover off showing motor runs. Problem is vacuum has no suction in hose area, cover off where bag is and the air blows out of filter. hoses are clean no blockage.


Have you checked the filter? Many vacuums have a filter under or behind the bag to keep dust and dirt out of the motor. If this gets clogged the motor can't get any suction. Also look for holes in the hose or in the small segment between hose and bag ... Vacuums

HOW DO YOU REMOVE THE TOOTHED DRIVE WHEEL FROM THE BRUSH MOTOR ON MY BISSELL 9200E CARPET CLEANER. ALSO IS THE ATTACHED UNIT THE MICRO SWITCH? WHY IS THE MOTOR COVER STILL ATTACHED TO THE FRAME WHEN ALL 4 OFF SCREWS ARE REMOVED JIM


It is a snap lock plastic cap on mounted to the frame. ... Bissell 9200 Upright Vacuum

My vacuum cleaner is making a loud squealing sound when I turn it on and the brush is turning. It gets louder while vacuuming the carpet. I tried to remove the bottom cover to see inside but, took out a bunch of screws and couldn't get the cover off.


... Kenmore Progressive Direct Drive 30912 Vacuum

On an old upright prolux plus, I just replaced the belt and cleaned out the brush motor, ran the vacuum for a bit, then the vacuum motor died...it's always run great. any suggestions of what to check?


... Electrolux Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1300 seconds