Having problems with your Polti Vaporetto 2400 Canister Steam Vacuum ?

Just got a Polti Vaporetto 1020 from someone and cannot get it to work. One yellow light lit up and was on for a few minutes then turned off...and there is nothing...flip the switch on the handle, nothing...flipped other yellow button, nothing...any suggestions? or where I might get directions on how to use it? didn't come with manual. Many thanks. best, pat

Answers :

Repair Help & Product Troubleshooting for Polti Vaporetto 2400 Canister Steam Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Just got a Polti Vaporetto 1020 from someone and cannot get it to work. One yellow light lit up and was on for a few minutes then turned off...and there is nothing...flip the switch on the handle, nothing...flipped other yellow button, nothing...any suggestions? or where I might get directions on how to use it? didn't come with manual. Many thanks. best, pat

... Polti Vaporetto 2400 Canister Steam Vacuum

The handle for my Eureka 5993 AVZ was getting very hot when used. Finally, the wires around the switch melted and now the vacuum will not work. What is wrong? Is the switch bad? The wires only melted in the immediate vicinity of the three-prong switch. Nothing else appears to be wrong; the vacuum worked fine when it was running - except for the handle getting hot. Thank you!

Try cleaning all...\015\012if have sam paoblem need replaced main motor.... ... Eureka 5893AVZ Bagless Upright Cyclonic Vacuum

Dyson DC01 - can't get starter button switch off.

This issue is known well with dysons to be honest you will continue to have this problem for as long as you have the vacuum. they use substandard plastic parts which break easy. You will have to replace the button and make sure there are no other ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Hoover on off switch won't turn off. I have to unplug the vacuum to stop it. I have dismantled the handle and now I can't get the inditation in the handle to fit over the little silver knob. I saw there was an on/off switch under the handle that is controlled by a piece of the handle. #1 question for the manufacturer is why don't they put the switch on the outside instead of having gimicks that turn it on and off... arghhhhhhhh

Don't know what model you have, but sounds like you will need to replace the switch. As far as your question, you will have to contact the manufacture for an answer. We only provide solutions to your problem and a model number would have helped. ... Vacuums

Hoover Upright Vacuum model U5470-900 - The On/Off switch on the handle does not properly engage the power switch deeper in the handle assembly. It appears to ride over the lower switch and doesn't engage it to operate it. If I play with it, I can get it to maybe turn on the vacuum, but, then the upper handle switch won't turn it off. Our current workaround is to use the power cord for on/off operation.

... Hoover Vacuums

I have an Easy-Flo central vac unit. The handle on the electric hose has a switch on the handle. With the switch on ''O'' in the center, it's off. On the left, is the ''I'' position. The vacuum runs but the power brush doesn't. On the right is the ''II'' position. The switch won't flip that way. It feels stuck. It feels as if there is something underneath of it that won't let it push that direction. I have the switch out of the handle, but I can't seem to get the actual black casing around the

Switches are not usually designed to be dissembled.I would strongly suggest that you dont take the switch apart. you are better off getting a new one. then if you feel like it you can take the old switch apart and if it dosnt work you still hav ... Vacuums

Switch I have a kenmore 31913 vacuum and the on/off switch appears to be bad. My problem is getting into the switch. How do I open up the handle to get to the switch?

Go to this website\015\012and enter your complete model number in the search field in the upper\015\012right corner of the page. You should be able ... Kenmore 31913 Progressive Direct Drive Bagged Upright Vacuum

Dyson dc25 schecking continuity on reset switch its a 91 series 2 amp switch but whether i have button pushed or not a get continuity shouldn't this break when button is pushed

... Dyson DC25 All Floors Bagless Upright Vacuum

I have the yellow altima vac. for a while now I can not get the darn thing to pick up properly. Or should i say keep it up.. The vac does seem to be getting everything picked up but as soon as you turn it off, you have a mess under the vac.. I have checked for clogks and can't seem to find any.. I have removed the hose, Nothing there.. And yep have removed the yellow thing inside the trash cup.. Is there anything else you could suggest??

If it smells hot, then there's a strain on the motor no doubt about it. Check the suction channel behind the sole plate and remove all of the hoses to check for a clog. It could well be that there is a clog inside the machine after the dust channel f ... Eureka Altima Upright Vacuum Model 2996AVS Vacuum

U5468-900 handle on/off switch no longer works. Switch on main body works fine. Seems like handle assembly has worn out. Can I get a replacement?

... Hoover U5468-900 WindTunnel Bagged Upright Vacuum

Tried pressing in red button and switch next to on button to get roller working but not made any difference - still wont turn (any no suction)

Hi there,I'm sorry to hear you're having difficulty with your DC24. If you haven't been able to reset the brushbar using the reset switch on the cleaner head, I'd encourage you to get in touch with us directly so we can provide further assist ... Dyson Ball DC24 Bagless Upright Vacuum

Electrolux Epic 6500 SR ...no power to power nozzle. I think it is the switch in the handle because if I use my friend's hose/handle (same model), my power nozzle works fine when I turn on the switch. If you think it is the switch, can I get a part for it?

That's about the best one to narrow down a problem, however, there could also be a break in your hose wiring. Switches, hoses, and hose handle assemblies are all available at your local Aerus Electrolux store. Simply take your entire machine in so ... Vacuums

I have a Eureka Upright vacuum (4800 Series). When I try to start it by turning the switch on, it wont. For few days, I was able to get around this problem by repeatedly turning the switch on and off until it turned on but that does not work any more. Could it be something related to the switch it self or the power cable. My wife mentioned that one of my kids might have pulled the power cable too hard (at the back of the vacuum). Any help to solve this problem will be very much appreciated. Tha

... Eureka Smartvac 4870 Bagged Upright Vacuum

It will work-about 1 in 50 times of trying. when i put in a file and press MDR button it makes a whirring sound and the screen will say any one of several things e.g.no disc or corrupt file.If the data file is put in before machine is switched on-i then get YAMAHA MDF 2 and nothing happens when i press the mdf button.

The unit is basically a floppy backup machine. In your case the actual floppy reading unit has failed. Since this is a custom mechanism it means that the unit is pretty much dead - no replacement parts for it. If you are willing to try everythi ... Vacuums

The retractable handle doesn't stay in place. a small spring came out near the button that you push to slide the handle up and down to change the length. i need to know where the little spring goes. there is a small pin that the spring fits around but i can't seem to get it to go back in place once the spring is on the pin.

... Panasonic Kenmore Canister Vacuum Vacuum

Power nozzle on E-series won't start when cold unless the red 'reset' button is pressed multiple times while also holding the trigger to 'warm it up'...this is w/the power nozzle off the floor - no restriction on it turning. Once it's been running and then turned off the button must be pressed w/the trigger to get it to run - again w/the nozzle off the floor. It also seems to shut off too easily while vacuuming. I replaced the motor,which didn't fix it. Is the reset switch next on my list? T

... Rainbow E series Canister Wet/Dry Vacuum

I have Nutone VX550C. Motor runs intermittently (cycles on and off rapidly--the light on the handle is blinking furiously) when I use the on/off switch on the hose. This happens at all of the wall connectors, so suggests a hose contact problem. Motor runs continuously when I turn it on at the switch on the wall unit.

The unit does have a switchs the PVC outlets, and it sounds like the hose mech to operate the switches is broken, and intermittently making contact. A replacement hose would likely fix the problem. Looked them up on the net, and they're not che ... Broan-NuTone VX550 Bagged Central System Vacuum

The handle was getting hot and we opened the handle and the wires were melted around the switch. I need a part number for it. All I have seen are 2 wire and this is a 3 wire. Thank you.

Had exactly the same problem with my upright Eureka Model 5893\015\012bagless. Eventually, the handle would get hot, and finally it just\015\012quit. When handle was disassembled, the wires were melted and it was\015\012toast. Ordered a switch aft ... Eureka 5893AVZ Bagless Upright Cyclonic Vacuum

Wind tunnel by Hoover, vacuum will not turn off by using switch on upright handle. do not see a way to get to switch. modle no. U5458-900

Follow the cord and look for screws inside the bag compartment at the top. a panel should lift off allowing access to switch and cord. If swtch is melted it must be replaced with special hoover switch kit which has new wire and heavier duty switch. b ... Vacuums

NO POWER My Dyson DCO4 Absolute (purple&lime) won't' switch on. I've checked the plug fuse, wall socket and also filters and hoses on machine all seem fine so think the problem is with the on/off button (maybe loose wire or something) but how do i get to it, is there a special way to remove the green on/off button in order to check the connection? Thankyou in advance for the help i am sure you will be able to provide.

The problem is almost certainly a fatigue break in the flex. These usually happen where the flex enters the handle through the rubber sleeve near the on off switch. You will need to cut about four inches off the wire and reconnect it to the switch. ... Vacuums

I have an Aerus Guardian canister vacuum with a clogged hose. The tiny stuffed animal toy is lodged right below where the swivel handle meets the hose. Switching the air flow does not dislodge it. I would like to remove the handle from the hose. Any suggestions?

Consider this. If your vacuum is still under warranty, removing the hose will void the warranty on the hose. I strongly recommend calling an authorized dealer/consultant.\012Although it may seem to be fairly simple to remove the handle, there ... Electrolux Guardian Bagged Canister Vacuum

Dear Sir: I just purchased a Bissell Rug Shampooer at a garage sale. The only thing I find for a model is on the back and it says Model 1695 there. Nothing on front. It is Navy blue and has a grey tank on it with a smaller one inserted at bottom of the large tank. It has two switches on the back of it and the trigger switch at the handle. The cleaner works, BUT, it does not extract any water back into the tank that is to pick up the dirty water. Could you suggest what I may look at t

... Bissell Vacuums

My bissell proheat upright steam cleaner is spraying out through the attachments just fine, but will not spray to the floor when using upright. we've taken it apart to find that there is no water at all going through one of the hoses, but it appears the hose is connected behind the on/off and heat switches, we can't seem to figure out how to get in there to replace that hose....any suggestions on how to access this?? just curious how you would get in to replace the hose, we know it is the hose..

Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

The handle for my Eureka 5893 AVZ was getting very hot. Finally, the wires around the switch melted and the vacuum will not work. What is wrong? Is the switch bad? Nothing else appears to be wrong.

Had exactly the same problem with my upright Eureka Model 5893\015\012bagless. It almost melted the handle! Ordered a switch after talking\015\012to several repair men. Talked to Eureka, too, and they were absolutely\015\012no help. Cheap wiring ... Eureka 5893AVZ Bagless Upright Cyclonic Vacuum

The unit does not start when I turn on the switch on the handle. The power nozzel runs, but the vacuum motor does not. The reset button is not popped, there is 110volts to the unit, and I tried flicking the switch inside the unit underneath the filter with no responce.

... Electrolux Centralux Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0803 seconds