Having problems with your Polti Vaporetto 2400 Canister Steam Vacuum ?

Polti Vaporetto 2400 does not heat water

\015 The power light comes on when plugged in but nothing else and it fails to heat up. Can you help me to isolate the fault please?\015\012\015\012Regards\015\012John\015

Answers :

Repair Help & Product Troubleshooting for Polti Vaporetto 2400 Canister Steam Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My polti vaporetto 2400, heats the water up, but the steam wont come out - help

... Polti Vaporetto 2400 Canister Steam Vacuum

Polti 2400 water will not heat - Polti Vaporetto 2400 Canister Steam Vacuum

It is more likely that the thermostat is not working than the element to have gone. needs stripping and checking then the faulty part to be replaced ... Polti Vaporetto 2400 Canister Steam Vacuum

Polti Vaporetto 2400 does not heat water

... Polti Vaporetto 2400 Canister Steam Vacuum

Have a polti vaporetto 2400 been used 3 times approx but out of warranty heats up ok but wont release steam when trigger pressed.have tried flushing water in tank with no results

These machines like to be used regularly. if allowed to sit (especially after using tap water) they may buld up lime deposits on valves and cause them to stick. you could try filling with vinegar and let set, also tilt it so vinegar runs into valve a ... Vacuums

Water isn't heating up in my Polti Vaporetto steam cleaner, although the lights come on on the switches ok. I live in Belfast, can u advise where I can go for repair please. Thanks Philip.

... Polti Vacuums

Polti Vaporetto 2400: Water out light comes on when tank is full

Hi you need to put 5ml of Kal Stop fo Polti machines into 1000/1500ml of water into the tank, The stronger solution is better (1000ml) Let it heat up and this should break down the limescale on the solenoid. I tried this today and it has worked sav ... Polti Vaporetto 2400 Canister Steam Vacuum

I have a Polti Vaporetto Lecoaspira 710. I have filled the tank and set the machine up as usual. When I turn it on the boiler pump runs continuously for a minute or so and then the 'beep' begins and the machine shows that the boiler is empty. Obviously the water is not getting through. We don't live in a hard water area so it shouldn't be 'limed -up'. The manual says to leave it to cool down and then try again. That had no effect. The only answer that Polti 'Service' could give me was to try 'G

... Polti Eco Pro 3000 Canister Steam Vacuum

Thermerstat iron leeking water - Polti Vaporetto 2400 Canister Steam Vacuum

Hi,Here is a tip that will help you with that problem...My Steam Iron is Leaking Water http://www.fixya.com/support/r5301301-steam_iron_ ... Polti Vaporetto 2400 Canister Steam Vacuum

Water leaking at bottom of machine - Polti Vaporetto 2400 Canister Steam Vacuum

... Polti Vaporetto 2400 Canister Steam Vacuum

Polti 2400 - fault --heats up to temp.but will not generate steam although you can hear the the click when steam lever pressed all get out is a small trickle of water . any answer ?

... Polti Vaporetto 2400 Canister Steam Vacuum

Heating up but no steam coming out - Polti Vaporetto 2400 Canister Steam Vacuum

Will be clogged up with limescale, you should use Kalstop to prevent this, it is a bio-degradable, non-toxic limescale remover-preventitive. ... Polti Vaporetto 2400 Canister Steam Vacuum


Hi, It is the solenoid that is sticking, It there fore needs opening up, the solenoid valve stripping and cleaning, or replace at a cost of about £12 then putting back together. they don,t like being left and not used. It is possable if you kee ... Polti Vaporetto 2400 Canister Steam Vacuum

How to descale a polti AS700? It heats up well, but runs out of steam before the water. There is sludge in the bottom of the tank.

... Polti AS700 Canister Steam Vacuum

My polti vaporetto leader won't heat up . power lights are on .

... Polti Vaporetto 2400 Canister Steam Vacuum

I have a Polti leco aspira 710. The water in the tank is heating but when the trigger is activated no steam comes through. The machine is showing one green light and is emitting a continuous beep. The vacuum cleaner is working fine - but no steam at all

... Polti Vacuums

Polti Vaporetto 1500 Unable to unscrew polti safety cap. ( nothing to do with steam as machine not turned on yet)

... Polti Vaporetto 2400 Canister Steam Vacuum

Polti vaporetto 2400. Steam is escaping from the central connector block. Help!

... Polti Vaporetto 2400 Canister Steam Vacuum

Polti Vaporetto 1500 safety cap won't screw off.

... Polti Vacuums

We bought a Philips Intellicare 8030 ironinng system in 2005. Two days ago water from the plastic water container does not go inside bigger water tank where we think the water gets heated up. When the heating tank is empty there is no steam that comes out of the iron. Also, there is water dripping off profusely from under the iron where the steam normally comes out. Can you please advise how we should remedy this problem Please advise which service centre in Sydney, Australia would we be able to

... Philips Vacuums

I just bought kaz model K76P (M) humidifier in Kyoto. I filled it to the right water level (a bit below) and plugged it in (nothing else is plugged in at that socket). The light comes on, but the water doesn't heat up. I can't read Japanese so can't read the instruction manual but it seems a simple procedure: fill with water, set the heating thing the water, plug in. Am I missing something or is the humidifier defect?

Take it back to the shop it should work and even though its in japanese ,they will know if your doing it wrong ,but i think it may have a damaged heater or a wire off where its been in transit ... Vacuums

Polti 1500 no steam just droplets of water

Before trying anything else make sure you turn up the pressure control knob in the direction of the + sign if it is turned right down you will have steam in the system and the gun will be heard to click open the flow control valve but you will not ge ... Polti Vaporetto 2400 Canister Steam Vacuum

The steam polti 900 hand gets very hot and steams water out

... Polti AS800 Canister Vacuum

My bissell pro heat 2x does not **** up the water from either the upholstery cleaner or carpet cleaner. Any thoughts as to why? The water and heat functions work it just does not pick up

First check the motor duct gasket. The motor duct gasket is visible once the tank is removed. It is located underneath the handle on the top of the base of the machine. It has a black rubber coating around it. If there is no suction there please let ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

I have a Bissell Pro 2x carpet cleaner. The water heats properly as well as spraying the cleaning product. However, when I go to suction the water from the carpets, the 2 in 1 water tank bladder works properly but there is no dirty water outside the bladder. I have only used this carpet cleaner ~ 5 times and in the beginning I had to empty the suctioned water quite frequently as it was dirty and it could not not hold any more water. So I have done 1 room and all the dirt remains in the carpet

Check that the suction cone is not blocked. Check that the filter or hose to the bladder isn't blocked as well. ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0521 seconds