Having problems with your Powr Flite PAS20DX Canister Vacuum ?
How do i set the sequeege when enstalling a new rubber,it seem to be grabbing and chattering.
Repair Help & Product Troubleshooting for Powr Flite PAS20DX Canister Vacuum
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
How do i set the sequeege when enstalling a new rubber,it seem to be grabbing and chattering.
... Powr Flite PAS20DX Canister Vacuum
Brush Roller Wondering if I need a new brush as well as a belt. The Roller seems to have trouble spinning when it makes contact with the carpet no matter how the height is set. Everything else seems to work fine. Do I need a new roller to fix this problem?
The bearings can go bad in the brushroll. It may need replaced, even if the brushes aren't worn. Helpful link....\015\012\015\012 ... Kirby G6 Bagged Upright Vacuum
ORECK VACCUM older oreck xl, new belt , new bag, checked for clogs, does not pick up as it used to, and, much harder to push, seems to grab or drag, why????
Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=747767\015\012Generic problem for all Vacuums\015\012ORECK VACCUM\015\012Posted by FISHERMAN928 on Jul ... Vacuums
On our new carpet (which is not that thick but thicker than the old) I can't set the carpet thickness high enough. The suction really grabs the carpet and bogs down my self-propelled wind-tunnel Hoover. I then have to push down on the handle to tilt the front up. The thickness setting is as high as it will go. Is there some way that I can further adjust this. The machine is about eight years old.
I can help you out only if you will let me know the front width of the machine. Alongwith the height which you wan't to give raise. KIndly give the width and elevation in cms. ... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum
How is the V-belt tension adjusted (Hoover Model U6439-900)or how do I know if the tension is correct? There seems to be a lot of "play" in the belt and I'm wondering if that is the reason the brush roll only turns as the wheels turn, regardless of the carpet height setting. And yes, the brush roll is set for carpet, not hard floor. Or is the cause of the problem something other than the V-belt? A new flat belt was installed when the machine was professionally serviced so I assume (?) that was a
The V-Belt is not adjustable. There are two ways the belt has no tension: (1) when the handle is upright, a mechanical lever takes the drive tension off the belt, and (2) the brush roll lever setting you described. The upper handle would have to be ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum
With a/c on max, and either excellarating or accending I seem to lose vacuum and vent goes to defrost , then when slowing down it goes back to normal settings. , check valve new, vacuum ball no leaks ????? blazer s10 1997 4wd
You need to repost this in the auto. repair section, this is for vacuum cleaner repairs. ... Vacuums
Windtunnel belt I have a new Hoover Windtunnel canister. The belt keeps coming off. It happened a couple weeks ago (several times after putting the belt back on) so I assumed I might need a new belt as it might have dried out at the store. I ordered new belts and today I used it for about an hour and the belt came off again, twice. There doesn't seem to be anything to hold the belt on the stem as it seems to slip off. I have tried it centered, to the left and to the right....can you help. I am v
I've successfully used a compatible belt - Royal 104425001 .It's still new, but for the time being at least - it works. ... Hoover S3765-040 WindTunnel Bagless Canister Vacuum
Bissell SpotBot model 7887 still seems to clean ok, but there is no wastewater appearing in its tank on normal "Fresh Stain" and "Set-in Stain" settings. Seems to work on the "Manual" brush setting though.
... Bissell SpotBot Robotic Wet/Dry Vacuum
Generation 4 Apparently, my belt came off while vacumming. I had a lot of hari entwind on the roller, so cleaned off the hair.... but now I can't seem to get the belt to stay "in place". Is it supposed to move around on the brush? or be held in place? It seems to me when I try to get the hook to grab ahold of the belt, it is going tohe wrong way to grab it. Please HELP!
First off get a new belt, I am sure this one has stretched. Then put the belt around the brush roll, put it in the center, put the bottom plate back on. Then turn the big knob on the front and turn it until it locks, you will know if it grabbed the ... Vacuums
We have an Equity Insta-Set model 40001 battery-operated clock. We cannot seem to set the time, month and date. The temperature seems to be operating. There was no instruction guide included in this package. Thank you for any assistance. Sincerely, Jan
Good afternoon,Equity has the instructions on their support page, but no actual instruction sheet is available: ... Vacuums
My Bissell BS3920F upright (similar to the 10N6F) has been working wonderfully for the past 3 years but suddenly seems to not pick up dog hair as well as it used to. It has been pulled apart by my husband to ensure nothing is blocking the hoses etc and when running the suction seems to be there. It seems to grab the dog hair and leave it in a straight line directly under the unit without picking it up. I then disconnect the hose and use to hose to pick up the dog hair. This works well but obviou
Check to see if your brush is not worn down, they do wear with age - compare the length of the bristles with a new one. Replace the brush ir there is a significant difference in bristle lengths. Also check the flexible ben ... Bissell Vacuums
Belts breaking/melting The original belt broke at almost 1 year so I replaced it. I changed the carpet setting to shag even though my carpet is very low pile to make it easier on the vacuum. I didn't get to use it but just a couple minutes and could already start smelling the new belt getting hot. I checked the roller and it is easy to spin. Not clogged with hair or dirt. Now the inside of the new belt has small pieces of rolled rubber instead of being smooth. The metal shaft that goes into the
... Dirt Devil M088905 Vision Bagless Upright Vacuum
New Kirby I own the new Kirby Ultimate Diamond Edition..G Series and the brushes are running OK and everything but it seems to be blowing things out and not picking them up. Can you help me. My serial number if 7051201028
Is the bag emptor all of the way on? It will blow out if it isn't, But being new, you must have a number to call, it is under warranty so they should be able to help you out. ... Kirby G5 Bagged Upright Vacuum
HOOVER 6430-900 Runs for about a minute or two and shuts off. Wait a while and it will run again. Changed the belts, new bag, new filter. Seems to put out a lot of heat when running.
Hoover Fined for Failing to Report Vacuum Cleaner Fire Hazard\015\012\015\012\015\012\015\012\015\012\015\012\015\012\015\012\015\012\015\012\015\012\015\012\015\012\015\012\015\012\015\012\015\012\015\012\015\012\015\012\015\012\01 ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum
Brand new Hoover Max Extract Deep Cleaner brushes won't turn. Read manual. Checked filters - all clear. Set Spin Scrub Mode Selector to a scrub setting. Brushes still won,t turn. However the brushes on the Spin Scrub hand tool rotate.
I have a Pelonis Dehumidifier Model MDF 1-20AE. I am not sure how to set the proper settings. It seems the unit is working but blowing out hot air which making the room rather hot. (My previous old dehumidifier did not have this problem.) Is there a User Manual that I can download on line? Thank you very much.
... Pelonis Vacuums
It's brand new - just out of the box! Noticed the dirty water tank is bone dry. There is no suction! The front removable nozzle seems to be loosely attached.. The metal clip doesn't seem to hold it tight. Not sure if that is the problem. But I have a very wet rug! Suggestion?
It sounds as if it wasn't assembled correctly. Was it already put together when you purchased it? It sounds like the Brush Bar Belt never got put on.Let me know if you need more help.Jim ... Bissell 1950-3 Quicksteamer Plus Vacuum
Hello, I have a problem with my Eureka Powerline bagged upright vacuum. It has a 12 amp motor and is model #4352, Type D. It was probably bought new in 1998. My problem is, while vacuuming today the motor seemed to slow down all of the sudden and then began smelling like burning rubber. I shut the vacuum off to check for blockages but could not find anything blocked. When I then turned it on again it runs but seems to only be running at 1/2 the motor speed and still has the rubber buring smell.
It sounds like a rubber sealing in the motor has come loose and is being constantly rubbed against the walls of the motor with would cause the smell and loss of motor speed caused by the fricton of rubber against the rod so if you can get to the moto ... Vacuums
Put in new clutch, but the brush does not seem to be lowering when you change between bare floor and carpet. Does not seem to be touching carpet when engaged. Still has good suction.
The brushroll must be broken ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum
I just bought a Samsonite "Freeminder Flex" backpack with handle. My issue is with the lock... The combination for this lock was set to open at 0-0-0. It opened and locked perfectly at first. But after following the instruction to set up the new combination code, it doesnt lock anymore....please help and thanks! Linda
My Hoover Windtunnel does not clean carpet. The machine keeps grabbing the carpet. It appears that even with the switch set for carpet, the machine keeps acting as though it were set for a hard floor. How can I fix it?
Move the height adjustment up a little ... Hoover U6476-900 WindTunnel Vacuum
What do you do to get the most suction power from the DC04 dyson zorbster. It seems the only way to do it is to bang it which can't be the right way.The settings at the bottom do not seem to work and I have no instructions.
Clean or change the filters every 3 months and maybe have it serviced every year ... Vacuums
Lost suction I've only used this vacuum a few times, it's practically brand new. Now, one I turn it on, it sounds fine, and the hose feels as if it's getting some suction, but it's not strong enough to actually **** things up from the carpet into the canister. I have completely emptied the canister and bought a new filter. Nothing seems to help.
TOSS IT and forget it! I have never used a hand vac that worked that was worth the effort of turning it on .... I suggest they are all junk ... I found very few vacuum cleaners ... actually **** especially anything made by dirt devil ... I do have a ... Dirt Devil Vibe AllPurpose Hand Vacuum Bagless Vacuum
I own a Eureka Optima 437 and one of the rear wheels are broken and cannot find parts for this. Where can I find parts for real wheel? I have a rear wheel that came off too. The wheel seems fine, but the plastic base that the wheel clicks onto on the underside of the vac seems to have cracked. I need a new plastic bottom. Any ideas?
Called Eureka Customer Service and ordered another part. They are mailing it to me free of charge!No more problem. ... Eureka 431A Optima Bagless Upright Vacuum
I have a Hoover Windtunnel U 6439-900. The agitator brush will not turn. I installed 2 new belts, # 38528034, and # 38528-035 There is so much slack in belt # 3852034 (brush drive) that it cannot grip the brush. There does not seem to be any adjustment to take up the slack. I've put in new belts twice now & cannot get brush to rotate or tighten the belt to the brush.
... Hoover U6630-900 WindTunnel Bagless Upright Vacuum