Having problems with your Powr Flite PD2500 Handheld Vacuum ?
I need a control knob for a power flight PD 2500
Repair Help & Product Troubleshooting for Powr Flite PD2500 Handheld Vacuum
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
I need a control knob for a power flight PD 2500
... Powr Flite PD2500 Handheld Vacuum
Old Sanyo 1500 watt "Power Control" vacuum cleaner. I need to remove the plastic covers that are attached to the on/off switch and the power cord recoil. This will allow me to remove the retaining screws for the upper motor cowling. The motor and wiring is clogged with wood dust and I want to blow the dust out using compressed air.
... Sanyo Vacuums
IjI need a new foot control for my old Elna model. It is an Elnasuper 62c/H401048. The foot control has the ID# of 447300-1, a new power chord would be great to. I have had this machine for40 years.
On turning the power on , bright light indicator (above the themostat) turns on and then dims again and the iron doesn't heat up at all. Any pointers on what needs to be done .. Model is TexStyle Control - BraunSI 18895 2400 Watt
I need control knobs (4) and (4)side curtains for model eaw-05cm1fd, air cond
Hi,Here is the information you need:\015\012\011 \015\012\011 \015\012\011 \015\012\011 \015\012\011 \015\012\011 \015\012\011 \015\012\011 \015\012\011 Knobs are part Number: 814109Side curtain is part nu ... Vacuums
Royal vacuum cleaner model 4600 wiring diagram I have a Royal Vacumm Power Tank Model 4600. I replaced the switch (6 wire - 3 position) that is on the tank. One side of the switch control just the blower. The other side control the blower and the POWER head - wand with a variable control speed. The middkle position is off. After I installed the swith, the power head - wand is powered in either position. There are three wires comming out of the wand: White, Red and Black. I guess I wired somethin
REMOTE CONTROL IS MALFUNCTIONING & NOT TURNING ON CUSHION - Hello. I bought a used (by near new) Shiatsu+ Massaging Cushion from Ebay. When I installed it today the remote control was faulty. When you push the Power button, the blue light comes on, but none of the other buttons work. When you push the Power button again to turn it off, it clicks & turns itself back on again. So it's running but nothing is happening in the massage cushion. I did see a card in the box saying "For the Shiatsu
Before you use this cushion you MUST first 'unlock' the rollers which are held in place by a screw which MUST be removed or the unit will self destruct. The manufacturer provides a hex wrench to remove the shipping screw and a large label on th ... Vacuums
I just bought a Hoover Power Drive Concept Two Electronic vacuum from the thrift shop. It only needed two belts and seems powerful. But i don't understand what the small red button on the handle marked "Release Drive" means. Thanks for any insight! Anything else i need to know about this machine? Is it a good one? Are there high-performance bags available for it?
The U6311-903 is a self propelled vacuum. The the small red button will stop the handle from moving back and forth, which makes the machine go foward and backwards. The red button disengages the self propelled feature. ... Hoover U6311-930 Power Drive Bagged Upright Vacuum
Need to replace power head for blue magic Need
... Kenmore Magic Blue 24195 Bagged Canister Vacuum
I need a new power cord for the power nozzle on my Electrolux 2100 canister vacuum. The power nozzle has part number N115M written on the bottom. I have found the power cord for power nozzles PN6 and PN7 online, and it looks identical in photos but I'm not sure if it's the right part.
You can buy the hose at an authorized Aerus Electrolux store. If near enough, they will deliver, if too far, they can ship it. The nearest dealer can be found using the below link. Just follow the instructions.\015\012Just provide the model ... Electrolux UltraLux 2000 Bagged Canister Vacuum
My danby kegerator model DKC645BLS controller circuit board corroded and no power to the compressor,I already have an external temperature controller,can I just bypass the controller and circuit board
Hooked everything up per directions. I plugged it in to the closest electrical outlet and nothing happened. The lights did not light up, the connected wall control and sensors leds do not light up. It appears the unit doesn't have power. The electrical outlet socket is fine as everything else I plug into it works fine. I have tried every other electrical outlet available. The unit won't power on from any outlet, and all of those outlets run other things, like power tools an refrigerators
Dear Davehibshman,Firstly; dismantle the plug and replace the fuse with the same rating as the one you have just taken out. Replace the plug cover, put the plug into the socket and try again. If this doesnt work, there may be a problem wi ... Vacuums
The iron needs a new power cord; however, the screw at the back of the iron seems to need a hollow star driver. What tool do I need?
You've identified it in your question. These screws are just one type of so-called "security" screws (there are many others) that are designed to be turned only with a driver that matches the head. You can often get these screws to turn with a small ... Vacuums
When vacuuming carpet with the electric power brush it will ocassionly , go to zero suction mode and shut off the brush. I have tried to cause it to happen by playing with the joint areas ( handle to tube and tube to power brush) without sucess. When the problem does occur I just turn the suction back on and power up the brush again at the handle controls.
You gave a good start to giving us good information to help you with solving this problem-- But I need a little more information:It sounds like you have the Electric Motor driven Power nozzle/ Floo ... Miele Blue Moon Bagged Canister Vacuum
Motor/Fan does not run. I have removed and taken the top of the canister plastic motor housing apart and tested for power. I have power through the cord to the switch and power from the switch to the two wire terminals. I have not removed the motor. Looks like I will need special tools to take out the motor. The Vac looks almost new. It has been setting for several years. What do you think?
Sorry to read about your problem, I hope this helps you out.Well you can order a new motor at shop vac, check out this link.you dont have to remove to check the motor, just connect power to the motor leads ... Shop Vac QPMH450 Canister WetDry Vacuum
The power wand electrical connection on the power unit itself seems to be corroded. I think I need a new two wire plug to plug into the wand. the model is a Eureka 6984 A. I am able to disassemble the power unit if necessary and replace the wire and plug if one is available
Try hesco inc they have a on line store with all the vacs parts diagrams and fast shipping. ... Eureka Vacuums
Flap My floor/ tools knob won't turn. The knob controls wheather you are going to use tools to shampoo furniture of floors. The flap and knob will not trurn
Most likely the diverter valve is broken part #2136988. You will have to remove the top to replace it. ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum
My Kirby G5 has a power problem. Its handle needs to be tiltled all the way to almost flat position for the power to comne on. If the handle is back up to its standing postion, the power will be off. What's the cause of this problem? Any suggestions/comments will be greatly appreciated!!!
Sounds like u may have a problem with the cord connection inside the power plant would suggest u take to repair shop not something i would suggest u try yourself ... Kirby G5 Bagged Upright Vacuum
Power head for my central vacuum powers on and need to be pushed
What brand system is it? by not moves do you mean it doesn't pull itself forward? chances are its a cheap rubber belt that is stretched out and needs to be a replaced. ... Electrolux Central Vacuum
Need to replace power cord on Hoover windtunnel need wiring help
Without seeing this it would be difficult to describe. I would take it to a vac shop and let him show you. there are no real schematics for the wiring of these units. I usually would cut off the cable with a few inches of insulation to know where to ... Hoover U5399-900 WindTunnel Lite Upright Vacuum
I need the rightmost knob. (The timer knob) (Oster toaster oven model 6071-000)
Kenmore Vacuum 116.35622: Need to know how to attach the board to the vacuum that is supply the power to the motor. (need the electrical diagram) email: firstname.lastname@example.org
How does the Miele Vacuum Power Nozzle Pinion Gear get taken off and a new one put on? Is it pressed on and just need to pull off or is it screwed off. It is for the SEB217 power head
Greetings,\015\012\015\012What you need to do is screw the Pinion Gear off of the power brush. This can sometimes be tricking, because as I'm sure you're aware, when you twist the pinion gear to try and release it, it also spins the mot ... Miele S318 Bagged Canister Vacuum
MY VACUUM ISN'T PULLING AS STRONG AS IT USED TO SO I THINK IT NEEDS A NEW BELT. I CAN'T FIND THE MANUEL ON IT SO I NEED SOME INSTRUCTIONS ON HOW TO CHANGE THE BELT. I DON'T WANT TO BREAK MY VAC. CAN SOME ONE PLEASE INSTRUCT ME ON HOW I SHOULD CHANGE THE BELT PLEASE. TYPE VAC: EUREKA THE BOSS WHIRLWIND LITE CYCLONIC POWER CANISTER TYPE VAC. THE HANDLE IS DETACHABLE TO CLEAN IN THE CORNER WITH A SMALL EXTENSION.
You can get Eureka replacement belts here:Eureka Vacuum Betls ... Vacuums
Power head on my Electrolux Epic stopped working. Do I need a new one or could there be a part that needs replacing. Can I open it to see?
Have you tried pushing the reset button? I'd try that first. If that doesn't work it could be that the belt is broken. The motors don't go out very often on those. ... Electrolux Epic 6500 Vacuum