Having problems with your Powr Flite PFX1350 Upright Steam Vacuum ?
9400 carpet bissellproheat problems
\015 Water does not heat up? thanks!\015
Could be a few things, heater switch or heater tank you can get spares off link below
Repair Help & Product Troubleshooting for Powr Flite PFX1350 Upright Steam Vacuum
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
9400 carpet bissellproheat problems
Could be a few things, heater switch or heater tank you can get spares off link belowhttp://www ... Powr Flite PFX1350 Upright Steam Vacuum
I have the same problem with intermitant power, however, it does not make sense that the problem is in the upper powerhead (which is what a repair guy told me) because-- when I use the other attachements it is fine. The problem only occurs when I use the carpet (big)attachment so that the roller will not turn. Couldn't it just be in the area where the bottom of the handle attaches into the carpet attachment?
You can test the auxiliary plug to the roller/beater attachment with a volt meter if you know how and take precautions. Check for 115-120 volts at the beater/roller attachment plug. If voltage is there and the beater/roller doesn't run, the proble ... Kenmore 23612 Progressive PowerMate Bagged Canister Vacuum
Suction problem I have a Hoover Widepath Fold Away, 12 amp motor vacuum cleaner and the problem I am having is every time I vacuum, the vacuum gets clogged up with carpet. I am probably only able to do one stroke then it gets clogged and I have to stop and unclog it or it spits it out on the carpet. This is very frustrating and I don't get much vacuuming done. Please can you help me. Thank you. Gwen email is [email protected]
Get rid of the carpet its shredding and falling apart.no sence in vacuuming old rotten carpet.or try using a vacuum without a brush roller and just suction ... Hoover U8145-900 Savvy Bagless Upright Cyclonic Vacuum
How to take apart the Hoover U6437-900 to change the belt and clean it. I have the belts and I have removed several screws. It looks like the knobs for the wheel carpet height and carpet to floor selection are the problems but I can not figure out how to remove the knobs. Besides, I am not certain if this is the problem. Do you have the instructions? Thanks
HERE IS THE MANUAL > http://hoover.com/file/500/ ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum
Suction problem my proheat wont suction water out of carpet,,, it made a mess of my carpets now, any one no how to fix the suction problem?
The valve on the bottom of the water bucket is not being pushed up enough to allow the vaccuum to go through. Perhaps a part is missing but I used a small ball bearing and a car vaccuum cap to build it up and now our works but it is still a piece of ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum
I have a dyson dc07 with a malfuncitoning clutch diagnosed here on fixya. I've replaced the clutch and the grinding noise when the clutch is engaged for carpet and non rotating brush problem presists. This is after replacement of the clutch with a new part. Install of the new part went well and there are no otehr apparent problems with the unit. Ideas? The unit is only a couple years old and not used that much on carpet. For an expensive vacuum I'm not that impressed with it at this point.
Greetings from GoVacuum,\015\012\015\012If you have replaced the clutch already, then this can really only be one other problem, and that is the roller brush. If the roller brush's bearing have locked up, and the brush is no longer spinn ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum
I have an animal dyson. The front nose dives into the carpet when moving the dyson in the forward motion, fine when pulling back. A huge amount of effort is required to move it forward. Took it to a technician and he said he could find nothing wrong. He had only short nap carpet for test. Works fine on short nap, if the carpet nap has any lenght to it like shag, the dyson severly nose dives. It's like the nose is sucked into the carpet. This problem just occured after the wife used the ho
... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum
I have a vax power jet carpet cleaner it is afew years old my problem is when cleaning carpets it makes black streaks all over the carpetwhenthe capet is dry you can see these streaks and it makes the carpet look even dirtier than before i went to wash the carpet . can you give me any suggestions as what is wrong thanks
... Jet Vacuums
Carpet vacuum attachment quit working after sucking up a bedskirt. Bedskirt has been removed but carpet attachment will not work. My old vacuum had a reset button on the carpet attachment for use when the carpet attachment sucked up something and turned off. Does the Hoover have such a feature, and, if so, where is it? If not, how do I fix the problem and how do I keep it from recurring? Model # S3765-040. Serial # 100700081298. Purchased 2/08.
I have a Hoover Conquest approx. 4 yrs old. The turbo head is not working Model No. PB4 230-240V AC 50Hz 200w CS4901N (N127) I have been trying to locate another one or another one similiar to fit my machine ... Hoover Vacuums
I bought Roomba 560 robot vacuum cleaner about 3 weeks ago and it has been cleaned without problem all kind of positions of floors (also carpets) Last friday I anyway mountained nearby of outcoming door the black carpet. Now the situation is that Roomba doesn't move and clean above of this carpet. What is the reason and how to solve it ... ?.
Ok, take regular WHITE paper. Do not press it on the sensor, just make it long enough so it covers the sensor. Then, take some clear tape, and tape the piece of white paper over it. Watch for the wall brush and stuff, don't get it to close to them or ... iRobot Roomba 560 Robotic Vacuum
Dirt devil vacuum cleaner--trouble vacuuming dirt and pet hair on carpeting --is the problem with the spinning brush which contacts the floor, not contacting the carpeting?? I thought (when I bought this vacuum) that the aforementioned brush was adjustable to various heights of carpeting. Sometimes, it seems like nothing is being vacuumed up --unless I have just put a new bag on the vacuum... Do I need or can I replace the spinning brush on the bottom of the vacuum so it kicks up and vacuums
Try replacing the belt. Rubber belts stretch out after about a year. ... Dirt Devil CE6100 Featherlite Upright Vacuum
I own a Bissell Proheat Pet Model 8910. After just a few uses and changing both the brush and pump belts (trying to resolve problem) carpet doesn't get wet any longer. Carpet solution comes out normally but the water barly leaves the section of the tank I fill water into, resulting in carpet recieving to much solution and not enough water. Any advice?
... Bissell 8910 ProHeat Clear View Upright Vacuum
Vax problem I have a Vax Rapide V0255 that will not wash the carpet. I have cleaned all the tanks etc but when i hold the trigger down it will not pump water onto the carpet can you help Thanks Claire
Take it back to the shop you bought it from - had similar problem with our Vax and it had to be repaired. Have used it once since and it is again not working. This time it just leaks solution all the time whether you are pressing the trigger or not ... Vacuums
I recently purchased this vacuum after reading consumer reports article on it and from recommendations from family. However, since I've had this vacuum it's been nothing but problems! I have a frieze carpet and I have the vacuum set on the highest setting. Each time I use it, the vacuum clogs with carpet fibers before I even finish a room! Any suggestions?
Is that a shag carpet? the power head is raised up all the way can you lower the suction on it is the carpet old the vacuum may not be able to handle the carpet,go to a vacuum store and see if you can try somthing else out some stores well let you re ... Hoover Tempo Widepath Upright Vacuum - Blue
How is the V-belt tension adjusted (Hoover Model U6439-900)or how do I know if the tension is correct? There seems to be a lot of "play" in the belt and I'm wondering if that is the reason the brush roll only turns as the wheels turn, regardless of the carpet height setting. And yes, the brush roll is set for carpet, not hard floor. Or is the cause of the problem something other than the V-belt? A new flat belt was installed when the machine was professionally serviced so I assume (?) that was a
The V-Belt is not adjustable. There are two ways the belt has no tension: (1) when the handle is upright, a mechanical lever takes the drive tension off the belt, and (2) the brush roll lever setting you described. The upper handle would have to be ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum
It,s the suction power. I need to go over and over the carpet to pick up small things on my carpet. I need yor help to solve this problem.
The top of the cyclone unit can clog with fluff, remove the 3 torx screws and carefully lift off the top, it won't come away completely as the flap release trigger rod is connected to the lid.\015\012remove any fluff you can see between the cyc ... Dyson DC07 Bagless Upright Cyclonic Vacuum
Bissell Powersteamer 1694W won't extract water from carpet. Was extracting fine until the pump/brush belt gear broke off off the pump. I repaired the gear with super glue and the brush is once again working fine. I now have an extraction problem. What did I do wrong? I took it apart and was so proud of myself when I fixed the original problem. Now I'm lost.
Check your re-assembly.\015\012\015\012Have you missed a pipe connection somewhere? ... Bissell Powersteamer 1694 Upright Vacuum
The hose on my Samsung 9048R is torn partly from the swivel base. The main problem is that the carpet attachment with the beater bar will not operate now. My brother checked the connectivity at both ends of the hose and there is juice at the bottom swivel part but at the other end of the hose where the carpet wand plugs in it is dead. is there any way to fix this? How does the wire go up through the hose? I have looked around on the internet and it would seem that the entire hose assembly is
... Samsung Quiet Storm 9048R Bagged Canister Vacuum
Kirby Sentria I bought my kirby sentria just before we were to move house and although I have the instructions somewhere, they will be boxed up and I so want to clean the carpets before I move. Problem is that I don't know whether the belt should be on or off when using the big silver front with the Kirby insignia on it. I know that the green light should come on when it is working properly and it does not, so I am doing something wrong. I can attach the attachments no problem but I want to use
If the green light is off, then its time to replace the band. This video shows you how. ... Kirby Ultimate G Bagged Upright Vacuum
I have a windtunnel upright self-propelled that is very difficult to push, on carpet or hard floors. Seeems that it is stuck to the floor and at times you can smell the rubber from the belts. What could be the problem or problems?
Raise the front. you are trying too hard ... Vacuums
Shag carpet problem with shag carpet, The oreck xl21 will not pull it's self.
... Oreck XL21 Bagged Upright Vacuum
My power brushes on my bissel carpet cleaner stopped working. They do not rotate. This is the 2nd power cleaner I have bought and it has the same problem as the first one. What is the problem with the power brushes. After 3 uses they stop working. Bissel Proheat 2X Model #8920
The brushes will only work if the handle is released and the ProHeat vacuum is running . There is a micro switch inside the lower handle that switches on the DC carpet brush motor. The DC power for the motor comes from a Bridge Rectifier on the PC ... Bissell Vacuums
Hoover F7431-900 my carpet shampooer/steam vac was working fine until the brushes at the bottom of it just miraculously stopped working. they wont spin at all. Is this a motor problem? perhaps a water flow problem? please write back if you can be of any help. thanks
If the screen is not dirty, and the flapper valve to the turbine inlet is open, then the problem is mostly a stuck turbine impeller. The turbine impeller on my F7431-900 has seized TWICE!! The shaft for the turbine is not made of stainless steel, t ... Hoover F7431-900 SteamVac Vacuum
Horrible noise The same problem that has been the other people have experienced, I can make the noise stop if I switch to floors, but it doesn't work well on carpets. Has anyone been able to fix this problem?
It sounds like you have a blockage. Go to this at Dyson to look at your item in more detail. They have good support here for your item. Just copy and paste into your browser.http://www.dyson.com/support/help.asp?product=DC17-ANIMAL&ar ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum
MY WIFE BOUGHT THIS FOR ME FOR FATHERS DAY GIFT ABOUT ALMOST 2 YEARS NOW OR SO,BUT I HAVE THIS PROBLEM THAT THE BRUSH DOS'NT SPIN ANYMORE EVERYTIME I PUT THE SWITCH ON FOR BRUSH ON,THE HOSES BRUSH SPIN IS WORKING BUT FOR THE FLOOR CARPET BRUSH SPIN IS NOT WORKING,AND THIS IS THE MODEL NUMBER OF MY HOOVER VACUUM CARPET SHAMPOO CLEANER IT'S F7411-900
This unit uses a turbine assy to turn the brushes. The brushes could have something jamming them. Remove the brush unit, it is held on 2 spring hooks 1 on each side. The brush unit is driven thru a 1/4" square post, only one brush is driven and it dr ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum