Having problems with your Rainbow E series Canister Wet/Dry Vacuum ?

How do you get to motor?

\015 How do you get to the motor?\015

Answers :

To get access you need to remove the plastic side cover panels. To remove these, I found the easiest way was to use a small flat screw driver, leverage it under the pastic in the centre at the 'cord end' and lift carefully. There are two lugs at the top and one at the bottom. The plastic panel will 'bow' a little, but with care, it will pop off. The gold looking vents underneath are just a 'facade'. By removing the side plastic panels they will expose three screws either side. Undo these and the top will half of the cleaner will lift off. Good luck!
Repair Help & Product Troubleshooting for Rainbow E series Canister Wet/Dry Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Does anyone know where I can get a motor bearing for the 3595 upright vacuum. Called Bissell and they say I have to be an authorized dealer to get "internal" parts and called their "authorozed dealer" and they told me they cannot get the part and I needed a new motor...ridiculous! Anyone put a bearing on these and if so where did you get it from?


Bought the whole motor assembly for mine, no bearing only part available. THis vacuum now headed for its third motor. " $45 dollars is still cheaper than a new vacuum". That's what I said the first time... ... Bissell CleanView 3596 Bagless Upright Vacuum

Miele Cat & Dog vacuum gets VERY hot and is VERY loud. Hose has no restrictions and I have changed the dust compartment (motor) filter and the exhaust filter. It still gets hot when I run it with the top open and all filters removed, so I'm guessing the problem is with the motor. Should I be going into the motor compartment? If so, what am I looking for?


Hi\015\012\015\012The fact that it gets very hot could be due to a number of issues.,but the fact that it started making a very loud noise at the same time suggests that there might be more problems maybe brushes etc.\015\012\ ... Miele S514 Solaris Bagged Canister Vacuum

I need to change the motor in a vax 6131 but i don't know how to get into it to get the change it? I also need to get into the motor assembly housing to change a part but can't see how it comes apart!!


On the handle there is one small pozidrive screw, remove and orange panel comes away revealing powercable securing bar. Remove 2 screws and this reveals a 10mm headed bolt. Under label on top of handle there is another small pozzi screw, undo t ... Vacuums

On my Kenmore whispertone 5.1 the bearings are bad on the motor there are two bearings they are listed as 608 BRS I see bearings all over ebay 6082RS 608SS but none BRS can I use any 608 Bearing or does it have to be a 608 BRS Bearing are these dry bearings or greased bearings I cant get any real information on the bearings I dont want to go to sears when I can get bearing much cheaper off ebay can some one shed some light on the bearings I would use the motor is made by Lamb Ametek went to ther


... Kenmore Vacuums

Flames and fine carbon particles came out of my Dydon DC29 which also partly melted the bottom filter. The motor is still working tho. I feel that the brushes are gone. How to get to the motor and where to get new brushes???


Hi Joel,I'm sorry to hear about your experience with your DC29. We'd appreciate the opportunity to provide further assistance, so if possible, please call us on 1800 239 766. Alternatively, if you email your contact details to us at ... Dyson Vacuums

I am getting very little suction from the motor. The hose is clear, the bag new. When I open the bag cover, plug the hose in and turn the vacuum on, there is next to no suction from the motor. What do you think is wrong? How do I remove the cord retractor to get to the two screws that hold the back of the canopy cover?


Your problem is probably is you don't have a proper seal in your chasis. A vacuum has to be sealed tight or the air will leak out and the seal broken. Check around the whole body after the bag is in and check for any airflow noise. I could help more ... Vacuums

I'm trying to pull the fan drive of my vacuum so I can get to the motor but Ican not seem to get it off. I was wondering if there is a release switch or something that is preventing me from doing this. Also the motor seems to be burning but I think it's because ther is something in there clogging it up.


Check to see if it has reverse threads, Most do ... Vacuums

This is not an electrolux problem, but I am hoping one of the experts can answer the question. I have a Sears air compressor that suddenly stopped working. After looking at how the motor case is put together, it appeared that it would essentially have to be destroyed to get it apart and into the motor. I received a new compressor for my birthday so I decided to tear into the old one to do some diagnosis. After getting into the case where I could see the motor/pump, I have discovered the prob


This is intersesting. I think the fuse is simply a heat sensor. If you by pass this the only problem you may run into is if the motor over heats it my eventually burn out. However, for what you are using it for overheatin should not be an issue. This ... Electrolux EL7020A Oxygen 3 Ultra Canister Vacuum Cleaner Bagged Vacuum

Dead motor I purchased a new motor for my Dyson Animal but I cannot figure out how to get the thing apart to replace it. There are weird star shaped screws but I can't even see how removing those would get me where i need to be. HELP!!!


Ace Hardware or Home Depot should have your star screws ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Motor wiring My Vax VS19TL motor died and I have managed to get hold of a new Vax 006 Turboforce motor which is the same size . My problem is that the original motor had two wires (black and white) which ran to the PCB switch. The new motor has three wires (black, white and yellow). I have ordered the PCB wiring loom for the 006 motor but I can't find any documentation that tells me where each wire goes. Can anyone help?


... VAX Appliances Vax X5 Bagless Upright Cyclonic Vacuum

Need to get to the motor to clean it and cannot get the cover off


... Eureka 6984A Bagged Canister Vacuum

Bissell proheat 2x 9200 series carpet cleaner. I need to remove the Brush Drive motor. However, this series has the gear end of the motor shaft poking out a hole on the left hand side. I removed the retaining washer and pin from the gear shaft. I need to get the gear off of the shaft in order to remove the motor. It's not budging. How do I remove the gear so I can pull the motor out of the unit? Thanks .


Chap, I wish someone had answered this. I'm having the exact same issue. ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Bad Motor? I have an upright Electrolux Prolux Heavy Duty "Appareil Industriel" and the motor does not seem to be working and turning the brush. Is there a trip switch somewhere to try and reset the motor? I have taken the plastic cover off on the base of the unit and cleaned it well, but can't seem to get the motor to start again.


... Electrolux Vacuums

MOTOR LOUD HOW DO I DISASSEMBLE MOTOR HOUSING TO LOOK AT MOTOR. TOOK OUT SCREWS ON BOTTOM BUT CANNOT GET TO MOTOR.


... Hoover V1 SteamVac SpinScrub Vacuum

Motor has strong burn smell and bad sparking.. Where can I get a motor or motor parts? Who makes this motor?


... Riccar 8650/8625 s Vacuum

I have a Necchi LYdia 3 machine type 544 The motor was overheating and I removed the bottom cover and examined the motor .It looked fine and ran well. It worked OK for a time and then got hot.I was able to partially remove the motor for inspection.I found that the cooling impeller was not secured to the shaft,I tightened the set screws and reinstalled the motor. In process of getting the drive belt back on I turned the wheel that extends out of the case to index the screw that attaches the bobb


Good day!Please try to re align the motor position.You have to do is repeat the procedure that you take to remove the motor and double check the alignment because all motor in misalignment is very hard to turn.And ... Vacuums

Shopvac 90L400 quit working (4 years old). Thought the switch was bad but not the problem. I read that there is a fuse link in the motor that frequently burns up. I tried to take motor apart but not sure of the process. I was able to get to the motor but cannot pull it out of the armature. It appears I have to take the aluminum blower unit off the shaft (it appears to be pressed on with a retaining washer). Do I have to take it off to pull the shaft and motor assembly out? Is that where the fuse


By pass the switch and take power right to the motor leads.. that should tell you if the motor is ok.. have not seen fuse link on a vac motor.. graingers has new motors, but not inexpensive ... Vacuums

Suction problem I have a Hoover Widepath Fold Away, 12 amp motor vacuum cleaner and the problem I am having is every time I vacuum, the vacuum gets clogged up with carpet. I am probably only able to do one stroke then it gets clogged and I have to stop and unclog it or it spits it out on the carpet. This is very frustrating and I don't get much vacuuming done. Please can you help me. Thank you. Gwen email is [email protected]


Get rid of the carpet its shredding and falling apart.no sence in vacuuming old rotten carpet.or try using a vacuum without a brush roller and just suction ... Hoover U8145-900 Savvy Bagless Upright Cyclonic Vacuum

I have a QSP Shop Vac 4 Gal and the motor has burned out. Can I get a replacement motor. These are some of the numbers on a label stuck to the motor FMC 01(F), FMC 02, 82122180, 27801 20 Thanks Carl Armstrong


... Shop Vac 285-00-10 Back Pack Vac Wearable Wet/Dry Vacuum

Oreck model BB870-AS - I was vaccuming when the vac shut off. The motor just spooled down and nothing more since. I have opened the case. Have power at the switch, and to the motor, but can't get a voltage reading to the common lead at the motor. Is there a fusible link, or something similar in that lead that might have burned out? Thanks!


... Oreck Vacuums

The pump motor in my Bissel Proheat 2x Plus seems to have failed. It was seized so I sprayed WD-40 in it and let it sit for 3 days. Now I can turn it by hand, but when plugged into the unit it still doesn't spin. Here's a picture: http://bbay.dreamhost.com/bissel_proheat_2x_plus/P1070021.JPG I wanted to take the motor out and hook it into another power source to see if I can get it going but it has 3 wires. I'm used to only 2 (+ and -). How can I hook the motor up to another power source,


... Bissell Vacuums

Samsung Quiet Storm Canister Vacuum VAC-9049 The motor will not run. Power is on to the motorized rug tool. How can I remove the upper housing to get access to the motor? I have removed the six visible screws, but the housing is restrained at the rear. I suspect there are additional screws under the power switch and cord retractor assembly, but I cannot remove that either. HELP!


Hi Daltm,\015\012Thank you for contacting Fixya. This is Anil.\015\012I understand that you need assistance n opening the Samsung Vaccum VAC-9049 motor. I will be glad to help you with it.\015\012Please go through ... Samsung Quiet Storm 9048R Bagged Canister Vacuum

My riccar rc1100 needs a new motor. motor is a daewoo and the armature is now bad causing sparking. how can i get a replacement motor?


You can purchase one from www.acevacuums.com ... Riccar RC1100 Compact Vacuum

Not exactly a blow gun. Convertible blower/vac - Sears Craftsman. Wire broke off ONE brush in the motor. Paid about $90 for the vac - Sears lists the WHOLE motor as one part - $88. Have requested brushes (they are provided with a lot of my 'cheap' Harbor Freight tools) but no go. Just get the canned reply - buy the whole motor. Actually got it working again... CAREFULLY drilled and tapped a 4-40 screw into the brush and soldered the lead to that... Always a way, isn't there?


... Vacuums

I have a Eureka 4870GZ. It turns on, but the brush roller doesn't move. The belt looks fine. I do have an extra belt and would try replacing the old belt, but I can't get the old one off the motor shaft or the new one on. I called Eureka customer service. The lady said there's supposed to be a small space between the motor shaft and the outside edge of the vacuum where I can slip the old belt off and the new one on. I don't see it. It looks like the motor shaft goes into a recessed place in the


Remove the top cover so that you can access to belt, You'll find 2 rows of 4 decorative holes on the top cover, In two of the holes you'll find the screws, Please use a flash light to see in that., Once the screws are removed, you'll be able to ... Eureka Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0741 seconds