Having problems with your Rainbow E series Canister Wet/Dry Vacuum ?

Not working properly

\015 I borrowed a Rainbow e series, When I turned it on the first time, it ran fine, after a while when i released the button on the hose, there was no sound from the "main vacuum"...and it wasn't sucking up very much, or what it did **** up, when the button wasn't being pushed, fell to the ground....is it possible to have too much water in the bottom.....did i ruin my mothers vacuum???\015

Answers :

Most of Rainbows water tank have a peg or a water fill line and should not be more then indicated. The separator should keep water out of the motor. Other then that you will need to have it checked.
Repair Help & Product Troubleshooting for Rainbow E series Canister Wet/Dry Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

When I set my sunbeam 3331-33 coffee machine to just brew, I can hear a click but it doesn't **** up the water to brew. I have not tried the grind and brew position to see if it will brew... any suggestions on what I can do? Everything is in properly (the lid is closed properly, the carafe is on properly)... Thanks.


... Sunbeam Vacuums

My eureka smartvac 4870 has no suction at hose or floor. all hoses are clear, filters clean and properly installed. bag not full and properly installed


Your eureka has no suction kuz the vacum hose needs cleaning ... Eureka Smartvac 4870 Bagged Upright Vacuum

My bissell Proheat will not spray any liquid on the floor, the brushes are working properly, my attachment hoses all work properly, there is just no liquid coming out to clean the floors, any suggestions...?


... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

My Dyson DC24 collects loads small particles of dust in the cyclone body.I tip with my hand to knock the chunks out of it. Is that proper collection?How do u assemble for proper clean out?


TWIST RIGHT THEN LEFT ... Vacuums

I have a Hoover Steam Vacuum, All Terrain, and the bristle brushes are not rotating. They appear to be seated properly and, the entire vacuum is clean and free of lint, hair etc., so everything is working properly except the brushes do not rotate. Any help would be greatly appreciated. Thank you.


I checked the owner's manual and the parts breakdown for your model F5807. Both showed that your model has a stationary brush strip and not rotating brushes. Is F5807 the correct model number? ... Hoover F5807 SteamVac Wet/Dry Vacuum

Not sure I connected wires back correctly after removing motor. can you tell me the proper wires to proper terminals


White to motor terminal,black to other motor terminal,green is always ground to housing. If for some reason the motor runs backwards, simply reverse the white and black leads. ... Oreck XL Ultra Bagged Upright Vacuum

I have vax 1800 pet vacuum. It is picking up fine but very noisy. I have replaced the belt in the past and the noise started then. On looking at it closely today I noticed brushbar was getting worn where it slots in at the side so I suspect it wasn't fitted in properly after replacing the belt. Now in properly but still making terrible noise. There is a bit of a rubbing noise when brushbar moved round. Do you think the brushbar needs replaced? How do I lubricate the bearings to try that bef


Spray the end of the brush-bar were the bearings are with WD-40 if that solves the problem replace the bearing when it starts screeching.. ... Vacuums

I have the kenmore 385- 81508. wen im sewing it seems that the thread is not properly hooking with the bobbin. it sews properly for a few stitches then skips


... Kenmore Vacuums

It leaves dirt and fluff in the rollers not in the filter. So is not cleaning properly. There is never anf fluff at all in the filter. Also the lid does not close properly and we constantly get the 'check tank' light coming on. It leaves streaky marks across the floor and seems to leave the floor too wet (hence the streaks). Look forward to hearing from you.


Is there something stuck in the air passage between the tank and inlet ... iRobot 5800 Scooba Vacuum

I have a Pfaff 7570 ... having a problem with the upper thread making a small loop just above the fabric by the eye of the needle, just before the tip of the needle is piercing the fabric, the stitches that produced are properly formed with the right tension, but the loops get in the way sometimes and I know it never used to do this before. After reading the service manual I'm suspecting the "thread check spring" is not functioning properly. The manual gives steps how to adjust it, but it d


Http://search-pdf-books.com/pfaff-creative-7570-sewing-machine-pdf/ ... Vacuums

My Bissell powersteamer has no spray releasing for floor cleaning. The spray attachment for upholstery is working. The tank is seated properly: The belt is attached properly. I bought this machine in Sept. 2009 and used it only 2x with no problems. It did a fantastic job. Can you help with this dilemma? Mark


... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum

I have a Bissell Pro 2x carpet cleaner. The water heats properly as well as spraying the cleaning product. However, when I go to suction the water from the carpets, the 2 in 1 water tank bladder works properly but there is no dirty water outside the bladder. I have only used this carpet cleaner ~ 5 times and in the beginning I had to empty the suctioned water quite frequently as it was dirty and it could not not hold any more water. So I have done 1 room and all the dirt remains in the carpet


Check that the suction cone is not blocked. Check that the filter or hose to the bladder isn't blocked as well. ... Vacuums

My Bissell Model 3760-4 is not working properly. The belt has been replaced (and checked 3 times), but the brush bar does not move when the brush motor button is on. The little metal turning piece that turns the belt is turnable with one's finger when the belt is off, but when we put it all back together and turn on the vacuum, the brush bar does not go around and the burning belt smell returns. The portable part of the machine works properly. It's the brush bar. It has been cleared of hair, etc


... Bissell Lift-Off(R) Revolution(R) Turbo Upright Vacuum

Bissell - Model 1697 - Powersteamer Pro - Carpet Cleaner I took the unit apart to replace some broken pieces and I can not seat the bottom to the top without properly engaging the soap/water mixer. What is the proper assembly procedure. What is the orientation of the water/soap mix valve when I seat the top to the bottom? The soap/water mix valve needs to engage the knob screw threads but this assembly is a blind operation. Do I turn to the soap/water mix knob to water only then seat the


Hi,\015\012http://dl.owneriq.net/7/7e477b7e-4440-49cf-a219-b68d301549e3.pdf\015\012This diagram will help you see the diagram plus the part assembly no and place it accordingly.I have also given link for Bissell - Model ... Vacuums

My kirby g series doesnt **** properly anymore. A friend borrowed it, returned it with a scratch and now its nto sucking like it use to. My son took the head nozzle off, could it be not put back on properly?


Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=722170\015\012Generic problem for all Vacuums\015\012My Kirby G series doesn’t\015\012Posted by m ... Vacuums

My wind tunnel keeps breaking its belt. The big one. The little one is properly attached. This is a recent problem so it has nothing to do with the rug height settings. I just broke two in the course of 15 minutes. The bag is NOT full, the brush/beater has been cleaned and properly attached Help.


Well will the brushes turn freely as they run in bearings if its got wool of cotton raped around the side of the brushs that will make them tight to turn and will brake every belt you put on it, in a flash,,,\015\012the other thing that causes ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Have model 3576-6 Bissell Cleanview II and drive belt keeps slipping off peg that is sticking out from motor pulley causing vacuum to stop working properly and brush to stop moving properly


... Vacuums

I have Hoover Floormate Model H3004. The machine will no longer dispense the cleaning fluid due to the trigger assembly not engaging properly with the inlet/outlet on the Clean Water Solution Tank. I have checked and made sure the tank was seated properly.


... Hoover Floormate H3000 Upright Wet/Dry Vacuum

Hi i have a Meile cat and dog TT500 and it is shooting out dust. cannot find instruction manual to see if i have inserted filters properly, i have bought a new charcoal air filter but lid will not close properly when i put it in, has someone got a pic of how it should look, if its not the filters what could it be.


As far as the filter, either it isn't in all of the way, or it is the wrong one as there are several different ones.\015\012\015\012TT500 doesn't come up as a good model number, should start with a S then 3 numbers and end with an i. It ... Vacuums

When the brush is on it won't **** properly


Look for blockage carefully as the unit does not know which you have attached. ... Miele S7210 Bagged Upright Vacuum

My oreck roller brush does not turn, belt is new and attached properly help


... Oreck Vacuums

Dyson Ball DC24 brush is not spinning properly...


Check it out with dyson, they might have others with this prob, just might be under warranty or be a recall.. ... Dyson Ball DC24 Bagless Upright Vacuum

Shampooer not delivering suds properly, and its not the suds screen....


I have had this issue numerous times. My husband fnally came up with the perfect solution. He wrapped teflon tape (PTFE tape) around the dumb screen and voila. No more screen coming loose. Mine has always been VERY loose. Infact it would simply fall ... Kirby Ultimate G Bagged Upright Vacuum

Hoover SteamVac won't spray properly


... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

Not rolling properly


Nothing is loose, but the roller just flops around instead of pressing down on the carpet. That lets the clear nozzle drag on the carpet. It seems there should be a spring of some sort pushing the roller down. How to get in to see if the spring is br ... Bissell 1697-7 Powersteamer Pro Deluxe Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0118 seconds