Having problems with your Rainbow E series Canister Wet/Dry Vacuum ?

What part of the vacuum was damaged or needs replacement?

\015 Party going on, kids left faucet on clogged sink, water leaked on rug, Drunk Owner used Vacuum in which the hose is not intended for wet usage. Vacuum would not start again.\015

Answers :

Probably got the motor wet. You would have to dissassemble the machine to verify damage to components. It may require a new motor there is not much else in these.
Repair Help & Product Troubleshooting for Rainbow E series Canister Wet/Dry Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My older Dyson DC14 (the purple one) early model with a clutch on the beater bar belt needs a clutch replacement. The bar has been cleaned and there are no worn or damaged parts so I conclude that the clutch at the motor end of the belt needs to be replaced. I can find the part online but no instructions on how to disassemble the vacuum to get to and replace it. Dysons only advice is to give me the address and phone of the nearest service center. Can you help me?

Have a look at www.dysonmedic.com which has some very useful info on dismantling and repairing Dysons.\015\012\015\012Although this site doesnt actually cover the DC1 ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

What part of the vacuum was damaged or needs replacement?

Probably got the motor wet. You would have to dissassemble the machine to verify damage to components. It may require a new motor there is not much else in these. ... Rainbow E series Canister Wet/Dry Vacuum

Kirby Vacuum Hi Bruce, In my opinion, yes the Kirby would be worth it, as long as you are not replacing the motor. The switch would be the most expensive part besides the motor that would need to be replaced. The switch costs USD 49.99, the cord is roughly $39.99, and the carbon brushes are $29.99. I can easily walk you through any of these repairs should you need help. Kirby's are great vacuum cleaners, that usually last 30+ years. Brand new these machines sell in the US for $1600 or more,

You can get better prices from Goodvac.com ... Kirby Generation 3 Bagged Upright Vacuum

We have a Kenmore Grab-N-Go Upright Vacuum with a Hepa filter. We lost the yellow filter canister that goes in the top of the vacuum and need to replace it and the filter that goes in it. Is there somewhere we can purchase a replacement part?

... Kenmore 34722 Grab-N-Go Upright Vacuum

We have a kenmore canister vacuum, the part that is attached to the wand that picks up the dirt doesn't work, when it's on the carpet the light does not go on. Do we need to buy a new vacuum or is there a replacement for this part.

Hard to say without the correct model number.\015\012\015\012However, you could check these things first:\015\012\015\0121- Is the belt that runs the brushes on the end pieces broken? If it is, is needs to be replaced.\015\0122- Is there ... Kenmore Vacuums

My mother purchased a replacement hose assembly for a Bissell ProHeat 2X and the part was shipped without any instructions... While I am pretty handy, my issue is with the supply tube, and I cant figure out how to accomplish the replacement, and as its not MY vacuum, Im hesitant to start taking things apart.I just need instructions to replace the entire hose assembly.

Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

I have a Kenmore Elegance vacuum and need a part number for a replacement hepa filter. Vacuum model is 116 30306400C. Thanks.

... Vacuums

Simplicity Jack turns off repeatedly during use. Vacuum doesn't feel hot. I have opened up the vacuum and have checked wiring etc.. Is there a faulty censor on the circuit board. How do I check or replace needed part?

... Electrolux Oxygen 3 Upright Vacuum Cleaner - EL5035 Vacuum

I have a electrolux oxy3 system vacuum cleaner. The floor is damaged, and the hose has been damaged and severed and the copper cables have been cut...so I need to purchase a replacement foot and hose/hand piece. regards Sandy

... Electrolux Vacuums

I have a Euro-Pro upright Vacuum model UV205H and I need the manual so I can find out the name of the various parts which I need to replace.

Try this site, they might just have the manual you are looking for:- www.retrevo.com/samples/Euro-Pro-manuals.html ... Euro-Pro UV205H Bagless Upright Cyclonic Vacuum

How do I replace the drive belt on a kirby G4? Actually the belt is already replaced I just need to know how to reattach that front part back onto the main vacuum. HELP

Greetings from GoVacuum,\015\012\015\012Here's a video we shot showing you in detail how to install a belt properly, and how to reattach the head properly. I hope this helps you;\015\012\015\012 ... Kirby G4 Bagged Upright Vacuum

Vacuum has new bag but won't pick up dirt. Cleaned flat filter and it made it worse. Do I need to replace rectangular filter or can I clean it. If so , how? If not, do I need to take it in for repair, ir should I get new parts? Thanks!

It's clogged somewhere. Disconnect the hoses where you can and check for obstructions. Run a coat hanger down the hose if you need to to clear the obstruction. ... Kenmore 31913 Progressive Direct Drive Bagged Upright Vacuum

I have a very old electrolux canister vacuum that needs the cord winder mecanism with cord replaced. Where can I locate this part?

... Electrolux Vacuums

I have an older EVO canister vacuum model 116. 22822200. This has a hose between the canister and the floor sweeper. Switches are on the hose. The hose needs replacing. Can you give me a price and part number for this hose? Can I order it at a store or on-line? Thanks, Alan.

... Kenmore EVO All Surface Floor Cleaner Vacuum

Need Replacement Parts - Vacuums

Where can I get the orange attachment that picks up the water from Hardwood floors? My cracked and I desperatly need a new one. THANKS! ... Vacuums

I have a Hoover Vacuum Cleaner, Runabout Supreme, on which the belt has broken. I purchased a new belt, part number 38528-040. I need some instructions on how to install the replacement belt? Thank you. JBS

Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=728341\015\012Generic problem for all Vacuums\015\012I have a Hoover Vacuum\015\012Posted by Jimbob48 o ... Hoover Elite U5061-900 Bagged Upright Vacuum

I need to replace the cord on an older Hoover upright, model S660, about 1986 vintage. The cord broke where it enters handle. Handle comes apart easily. Just not sure how to pop the switch out without breaking it. Was looking for a manual online to see parts diagram and/or instruction on disassembly and cant seem to find one for that old of vacuum.

Check ebay. those vacuums are worth fixing. I loved them. they would **** the carpet off of the floor! those cords aren't hard to replace.just remember the way you got the old one out. ... Vacuums

Need a replacement fuse for my Hayden vacuum - part number is LR88617. Terry Alphonse [email protected]

... Broan-NuTone CV353 Central Vacuum

The metal plate at the front of our X4 Extra has been damaged from nail heads on timber floors and although we have straightened it, we now need to replace it. We have ordered the part but cannot see how the plate comes off. We are reasonably practical and should be able to do it if someone can provide some guidance.

... Sebo X4 Bagged Upright Vacuum

Motor is sparking and smells like burning rubber. When it first happened I thought the vacuum had something jamming the beater bar. That was the smell it had, like when the belt gets burned. But when we turned it over, it wasn't jamming. Took off the base plate and turned it on. The motor area is sparking and it makes a weird noise (I assume that is because the motor fails and restarts). I looked for loose wires, can't find any. I believe I need some sort of part replaced, maybe even a n

From sound and description most possible is motor is burnt up sparks usually mean metal on metal either bearing or bushings went on motor if u can jiggle the shaft thats bearing if u rotate the shaft by hand and feel and or hear rough grinding the br ... Oreck Vacuums

My Dyson Aminal Vacuum simply will not turn on. I plugged it in this morning, pressed the power button- and nothing. No warning sounds, simply silence. Sigh. Nothing is wrong with the wall outlet.The vaccum is 3 years old but has run perfectly until this point. The brushes are clean of any accumulated hair. What part might need replacing?

The power switch may need to be replaced. Call the Dyson helpline - they will give you the location of an authorized Dyson dealer in your area who will be able to replace the switch. ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

I have a Electrolux Oxygen model 6996 A. The power head and the dog hair hand tool no longer spin. What wouod cause this and what part would I need to replace if necessary. I have owned this for 6 years (7 kids, 2 dogs) and it is an amazaing vacuum! Thank you. Susan

... Eureka Oxygen 6996 Bagged Canister Vacuum

I have a Panasonic MCV7515 UPRIGHT VACUUM and need to remove the cowling that covers the brushes to clean the hair out of the bearings, but it isn't clear how that can be done without a crowbar or sledgehammer. Removing all the visible screws makes the hindmost part loose, but not the front half. Also, is there an easy way to replace the belt?

... Panasonic MC-V7515 Bagged Upright Vacuum

I just recived a free Kirby G3 vacuume. the only problem is the on/off switch dosen't work and someone took it apart before i got it. all of the parts are there as far as i can see but they did not label the wires I need a diagram to be sure that i replace them correctly. Where can I find one?

... Kirby Generation 3 Bagged Upright Vacuum

Replacement parts dirt devil pool vacuum

... Dirt Devil Rampage Robotic Pool Cleaner Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0927 seconds