Having problems with your Rainbow E series Canister Wet/Dry Vacuum ?

Power head handle wiring

\015 It is striped and has a sharp bend on it like it wraps around a screw but it is not smashed like you would expect.\015

Answers :

Ok it is a grounding wire and it hooks to the place under the switch and then it hooks over the metal part of the wand where it slips into the plastic sleeve.
Not sure, I had a chance to look at one earlier, there was a wire that came off of the hose and went to that point above the trigger. Is that wire by the trigger intact or broken off? I may be able to look it again on Monday.
Repair Help & Product Troubleshooting for Rainbow E series Canister Wet/Dry Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

The brush wouldn't work when the selector switch was in carpet mode. Took the power head apart and removed the motor. Everything o.k. in the power head. Checked and found that the neutural wire had pulled out of the connector, the connector was never crimped at the factory. What a day! Took 2 hours and a large pizza to get it done. Neutral wire was in the hose just below the handle. Reconnected the wire and crimped it, put everything back together. It works!!!!

Great. ... Kenmore Vacuums

E series power head handle, internal wire came lose

Here is a pix.\015\012\015\012 ... Rainbow E series Canister Wet/Dry Vacuum

We have had the power wires that run through the swivel elbow at the end of the main handle extensions and the power head break after being repaired two times. The new swivel elbow and wiring connection was installed bya local, non-electrolux vacuum shop each time. What is the trick?

Have them replace at the Aerus Electrolux shop. Aerus uses a higher grade plastic (Lexan, read about it on the net) which should last the life of the the power nozzle and wands. The part and labor will have a 1 year warranty. ... Electrolux Epic 6500 Vacuum

Power head handle wiring

That wire goes just above where the trigger is, take the trigger out and there is a slot that the end goes into. ... Rainbow E series Canister Wet/Dry Vacuum

Royal vacuum cleaner model 4600 wiring diagram I have a Royal Vacumm Power Tank Model 4600. I replaced the switch (6 wire - 3 position) that is on the tank. One side of the switch control just the blower. The other side control the blower and the POWER head - wand with a variable control speed. The middkle position is off. After I installed the swith, the power head - wand is powered in either position. There are three wires comming out of the wand: White, Red and Black. I guess I wired somethin

... Vacuums

E series power head handle, internal wire came lose

Think it comes off of the hose. Maybe it broke off. ... Rainbow E series Canister Wet/Dry Vacuum

Power head handle wiring

Ok it is a grounding wire and it hooks to the place under the switch and then it hooks over the metal part of the wand where it slips into the plastic sleeve. ... Rainbow E series Canister Wet/Dry Vacuum

I have a motor for the Bissell 3750 power head with a black and brown wire, which wire is connected to what?? The old motor just had 2 black wires. There is a blue wire coming from the vacuum and blue wire coming from the light that are together, and a blue wire coming from the light and a black wire that are together. What does the blue and brown wire coming from the motor connect too? Thanks

... Bissell 3750 Lift Off Bagless Upright Vacuum

The power head keeps shorting out during use. one of the connecting prongs from the handle to the power head is black instead of silver and is smaller in diameter like it has been arcing inside the connection. could this be the problem and if so can I replace it or will I have to take it to a repair facility. Thank you for your help, Jim Carey [email protected]

This is a problem with the connection in the wands and the powerhead. Because they are shorting out you may have to replace the neck on the power nozzle. (Leave that to a pro). But you will definatly have to purchase a new wand as replacement wires a ... Electrolux Lux 7000 Bagged Canister Vacuum

The power head of my DC 21 keeps cutting off as soon as I start moving the hose around. The only way to get it going again is to step on the main switch on the canister, then the whole cycle of off and on starts again. I have replaced the entire power head and tested the continuity of all the wires in the hose and they are good. The repair shop says the PCB is bad but can not get one. What can I do ?

Not much. my only suggestion is to dig through the internet and try and find that pcb it may take awhile but it would be worth a shot. if you dont think you can make the repair take it to repair shop with new pcb and let them do it. ... Dyson Genuine DC-21 "Stowaway" Spare HEPA Filter, Dyson

Electrolux EL7024A vacuum power head wiring

... Electrolux Vacuums

Shark navigator power head will not turn on unless main handle is lowered to the floor

... Dyson Vacuums

Sears 116.31913 Lower units, vacuum motor and agitator power head do not have power/115v to them and won't run. I'm trying to take the handle apart to access the on off switch. I've taken all observable screws out and cannot separate the handle and section immediatly below the handle to access the on/off switch, to trouble shoot. Any tips for separating the plactic pieces enclosing the on/off switch?

... Kenmore 31913 Progressive Direct Drive Bagged Upright Vacuum

Dyson DC17 Animal does not have enough suction from the wand handle to power the mini turbine head. The wand handle has very little suction.

My dyson doesn't have suction either and nothing is blocked. In fact is was working great the vac that is, but when I used the wand for the first time to get the corners the vac shut off, I checked the hoses, filters and all nothing is blocked. ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Kenmore canister model 116.25513506 wont turn on. when handle switch is turned to floor. vac motor does not turn on. When switch is turned to carpet, floor nozzle works but vac motor does not. I checked fuse, all o.k. checked continuity for plug, o.k. removed wires for bag full switch...motor wont run. I wired motor directly power cord...motor runs. Thinking it must be the circuit board, how do I bypass it or test it?

... Vacuums

Power Cable wires exposed where it enters handle

Part of your question has been cut off by the FixYa system, but I guess you say the wires are exposed where the flex enters the handle. To dismantle the handle, first remove the handle from the machine and, of course, be sure the flex is not plugged ... Sebo X4 Bagged Upright Vacuum

Rain bow E series power head

\015\012\015\012Here is a pix of it. ... Rainbow E series Canister Wet/Dry Vacuum

I have a Broan Nutone central vacuum. The power head seems to stall unless you lift up on the handle. I think I may need to change the belt but cannot find a place to purchase one to see if this is the problem Model number BN180 type 1

You are correct, you need a new belt. You can find belts for the Broan BN180 at www.vacbelts.com. ... Vacuums

Sebo has become erratic in electrical power and today I have sparking from the top of the electrical lead where the wire goes into the handle. Can this be fixed?

Yes it can be fixed. If you are handy or someone in the house is handy you may even be able to do this yourself. All that is required is to remove the one screw out of the handle there near where the cord goes into the machine ... Sebo X4 Bagged Upright Vacuum

I have an Ambassador canister model Electrolux. The powerhead shut off and the brush doesn't turn. There is nothing wrapped around the brush and the connection from the handle to the power head is fine. Any suggestions? Thanks AG

CHECK TUBE-SUMO ACTIVE ( PART NO: 1131402-02 ) CONNECTION AND NOZZLE-SUMO ACTIVE OR REPLACED (PART NO: 1131400-02) ... Electrolux Lux 7000 Bagged Canister Vacuum

I need a wiring diagram for the power head, model S3601.

Hi,\015\012\015\012It would be better f you can find the Model Number as some of the manuals are applicable for different models of Hoover vacuums and for this reason the manual may not have the exact name of your cleaner on it.\015\012\0 ... Hoover Powermax S3601 Bagged Canister Vacuum

Carpet head doesn't have power to it from the handle area

... Samsung Quiet Jet 9068 Bagged Canister Vacuum

Kenmore progressive mod. 116.25615500 vacum cleaner. Wire harness pulled out of handle and is on the power brush. Can iI just reinstall it harness is still in good shape? Thank you

... Kenmore 25614 / 25615 Progressive Bagged Canister Vacuum

Oreck Upright Hi Redev, I'm not sure what model I have (about 6 years old...upright, looks like the one in the picture). I changed the belt (which was torn) and then the next time I used it, it cut off on me. Now if won't turn on at all. (I turn the switch on and off and nothing happens as if it is not plugged in but it is!). I noticed at the top where the power cord enters the handle, it is all frayed. Could the electrical wires have detached? Anything you think I should check before taking it

The cord could be bad and will ahve to be replaced. It would have to have a problem inside the handle or down by the motor. ... Oreck XL2600 Vacuum

Hi-My power head won't work anymore. How do I know if it is the switch or the wireing or how to fix it.

Can you take a test reading with a meter from the vac socket or the hose handle. If you have power there test the cord for continuity before the motor. Disconnect the wiring from the switch and bypass directly to the motor. TIP Most power head ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0484 seconds