Having problems with your Rainbow E series Canister Wet/Dry Vacuum ?

Replace EL cord on E1 Raibow vacum

\015 How to replace electric cord on E1 Raibow vacum\015

Answers :

Repair Help & Product Troubleshooting for Rainbow E series Canister Wet/Dry Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Replace EL cord on E1 Raibow vacum


... Rainbow E series Canister Wet/Dry Vacuum

How do i replace the power cord on my breeze vacume? i cant seem to be able to split the vacume.


... Dirt Devil& Breeze Vision Canister Vacuum Vacuum

VACUM CORD REEL REPLACEMENT


You can get the cord reel from the link belowhttp://www.ereplacementparts.com/hoover-uh70212-windtunnel-series-vacuum ... Hoover Vacuums

1 ) how do you open the body of the vacum ? 2) How to replace the power cord? Epic 6500 sr


Very Carefully! LOL! Disconnect the hose from the door. Open the door. Remove the bag. Flip the vacuum on its top. You will then need to remove the trim pieces from the sides by sliding them toward the front of the machine(bag opening). Usually they ... Electrolux Epic 6500 Vacuum

Hello i have a shark vacum cleaner model sv736k 15.6v handheld and the charger cord melted charger ka12d240015033u where / how can i get a replacement phil [email protected] kind regards


... Vacuums

I have a shark vacum cleaner model sv736k 15.6v handheld and the charger cord shorted and corroded the contact. I need a replacement charger ka12d240015033u where / how can i get one?


... Vacuums

Kenmore vacum wand power cord


Http://www.vacsew.com/vacuum-cleaners/kenmore-vacuum-parts.html/Try here ... Vacuums

I need to replace electrical cord on hoover windtunnel UH70120. How do i get the cord reel off? Can i open the cord reel to replace the cord?


... Hoover Company Wind Tunnel U53019 Upright Vacuum

Cord replacement I need to replace a damaged cord (the reel works). How do I get the top off so I can remove the back end? Once I get it off, will I be able to change the cord, or do I need to buy the whole reel assembly? (and thanks for the help - I love this site!)


You will probably have to replace the whole reel cord. Depending on your model, on each side, there is a bar in the middle that will slide off, then the 2 halfs will come apart. They will only slide in one direction. If an older model, there are s ... Electrolux Lux 5500 Canister Vacuum

I need to replace the plug in cord on my rowenta iron. I would replace but I paid $130 for iron and my cats have chewed on the cord so I thought it "might" be a simple replacement.


This is the second cat-chewed-a-wire question tonight.\015\012\015\012The only thing to do is to replace the entire cord. You could cut out the chewed section and splice it with **** connectors and electrical tape, but you have a nice iro ... Vacuums

Can you just replace the cord on a sebo vacuum or do I have to replace the handle with the cord


... Sebo X4 Bagged Upright Vacuum

I also have a Hoover upright and I need to replace the electrical cord. I have dimantled the back, where the tools are stored, and the hose. I still cannot find the screws or whatever, to get to the area behind the cord, so I can replace it. I think I will have to take off the bottom too. Has anyone out there tried to do this? It seems crazy. This machine works great so I hope I can also put it back together. Thanks for the help.


Since I do not know your specific model I can only supply you with general instructions. Be aware that most of the time you only need to gain access to the on/off switch to replace the power cord. Also Make sure that you are replacing the existing co ... Vacuums

I have my vacume electrical cord tangled inside and disconnected (I can see the open end of the connection from the power cord collector wheel! I need to take the vacume apart so get access to the wire inside. I need to know if there is something else to open other than the 4 screws. Your help is highly appreciated in advance.


Since you did not provide a model number for your vacuum, it is difficult to provide any precise directions regarding disassembly.\015\012\015\012However, most vacuum cleaners are fairly straightforward machines, and as long as you unplug ... Vacuums

Replace a melted Duralit toaster cord that melted from it touching my toaster oven. Need to replace the whole cord. Thanks, Shelley


Cut the bad part off the ac cord then use "****" conector to crimp on a new cord. make sure and note the stripe on the cord and that indicates the neutral wire. the stripe is on the outside of the cord on one of the sides. the stripe is molded on ... Vacuums

Vacuum not running; do I have to replace the cord winder or just cord?


Typically, the cord and winder are supplied as a unit.  It is possible to fit new cord to an existing winder, but the amount of labour involved will make the job more expensive than simply exchanging the complete unit.  Even if you're going ... Miele S514 Solaris Bagged Canister Vacuum

Have an older model Electrolux canister model. The electric plug is broken so I got a new plug to put on. When I cut the cord to replace the plug, the dang cord retracted into the unit. So how do I get access to the cord area so i can find the end to the cord!


Hi,\012\012You have to open the vacuum cleaner and look for the wire.\012\012It is located inside the circular wheel, where it wind itself up.\012\012Don't be afraid to open it, unless your willing to pay somebody just to install a ... Electrolux Vacuums

Replace Cord on Filter Queen with Cord Reel


... Filter Queen Cheetah II Ash - MU305 Bagless Canister Vacuum

I have a very old electrolux canister vacuum that needs the cord winder mecanism with cord replaced. Where can I locate this part?


... Electrolux Vacuums

Need to replace power cord and can't find how to open canister to replace


I had the same problem and could not find the other screws. You need to pry off the power cord retraction button, you will find two more screws under there. It's pretty easy after that!!!! ... Kenmore 22612 Bagged Canister Vacuum

The power cord on a flat iron broke/got chewed through and needs to be replaced. how can I open it to get at the cord or fix the cord?


... Vacuums

I need to replace the cord wrap part that flips up to retain the cord and down to release the cord and can find the part to order one.


You can locate your nearest dealer through the Hoover web site and then call them to order you one. once they have it in you could take the vac to them for the cord hook to install for you. ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Hi , I have replaced the electric cord on Electrolux Lux Royal vacuum , but the rewind that retracts the cord does not pull it in . The coil spring looks ok but it will not pull the cord back in , any suggestions please . Thanks Dave Ryder


Http://www.geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=564353\015\012Generic problem for all Vacuums\015\012Hi, I have replaced\015\012Posted by dryder on May 02, 2008 ... Vacuums

I have an aerus electrolux guardian canister vacuum. The cord was damaged but the retraction winder is still fine. I have ordered a replacement cord but I have no idea how to remove the old cord and install the new one. Am I over my head?


The winder is activated by a coil spring located in a drum. The drum transmits the power from the wire with 2 circular contacts. To replace the cable you must dismantle the case to access the drum, take the spring pressure out carefully as to not let ... Vacuums

I've lost my cord for my West Bend vintage Flavo-matic 8-cup 3280E percolator coffee maker. It does not take the standard 1/2" wide cord replacements which I've tried. The prongs look more like they're 3/4" wide. Would anyone be able to recommend an online store that may have this dimension of cord (and will ship to Canada)?


... Vacuums

Power cord Cord is just all knotted a twisted, i bought a rubber cord and just want to replace the original. I have removed all the screws from the rear of the machine and it still doesn't want to come apart and i dont want to force it. any help is appreciated.


If the cord goes in at the top, take the handle off, then remove the tool holder, then you can get to the cord. If it goes in at the bottom, You have to take off the motor cover to get to the connecting end. ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0385 seconds