Having problems with your Rainbow E series Canister Wet/Dry Vacuum ?

The Rainbow vacuum doesn't work on high speed, though it will work for low, what could be the problem?


Answers :

Repair Help & Product Troubleshooting for Rainbow E series Canister Wet/Dry Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

The Rainbow vacuum doesn't work on high speed, though it will work for low, what could be the problem?


... Rainbow E series Canister Wet/Dry Vacuum

The e series rainbow 2 speed works only on low speed. High speed will not run. What is srong?


It is either the switch or the controller. Call us and we can see if it is still covered under your warranty.RainVacwww.rainvac.com800-523-0510 ... Rainbow E series Canister Wet/Dry Vacuum

My rainbow vacuum will not start in high speed but runs in low speed


Yes, it sounds as if your controller is bad. Give us a call and we can see if it is still covered under your warranty.RainVacwww.rainvac.com800-523-0510 ... Rainbow E series Canister Wet/Dry Vacuum

Low suction I have a Hoover central vacuum system. I've reset the fuse box, checked the fuses, all of the lines are clear and there are no holes for escaped air to travel out. The filter has been cleaned as well. The vac works well with high suction when hooked directly to the unit, however when using any of the indoor connections there is extremely low suction. The machine still turns on so I do not believe it is an electronic issue. I have troubleshooted the issue as best I could and would


... Hoover L2310 GUV Central System Vacuum

Hello, I have a problem with my Eureka Powerline bagged upright vacuum. It has a 12 amp motor and is model #4352, Type D. It was probably bought new in 1998. My problem is, while vacuuming today the motor seemed to slow down all of the sudden and then began smelling like burning rubber. I shut the vacuum off to check for blockages but could not find anything blocked. When I then turned it on again it runs but seems to only be running at 1/2 the motor speed and still has the rubber buring smell.


It sounds like a rubber sealing in the motor has come loose and is being constantly rubbed against the walls of the motor with would cause the smell and loss of motor speed caused by the fricton of rubber against the rod so if you can get to the moto ... Vacuums

Need instructions for 8qt pressure cooker, model 65999. All it has on lid is a dial which says 'open', 'low', & 'high'. If it had a pressure guage it wouldn't be a problem, but I have never worked with a pressure cooker with a low - high dial. Please advise.


Hello. Here is a complete set of generic pressure cooker instructioins http://missvickie.com/workshop/stepbystep.html\015\012\015\012J. ... Vacuums

I have a Eureka Upright vacuum (4800 Series). When I try to start it by turning the switch on, it wont. For few days, I was able to get around this problem by repeatedly turning the switch on and off until it turned on but that does not work any more. Could it be something related to the switch it self or the power cable. My wife mentioned that one of my kids might have pulled the power cable too hard (at the back of the vacuum). Any help to solve this problem will be very much appreciated. Tha


... Eureka Smartvac 4870 Bagged Upright Vacuum

Vaccum is making a loud high pitched sound, doesn't work well through the hose or the floor piece and shuts its self off after about 5 minutes. I have cleaned the entire vacuum out several times but this problem persists. Usually after I clean it, it'll work for a couple months, not this time. Vacuum is only 2 years old, is this typical?


... Dirt Devil Featherlight Bagless Upright Vacuum

Bisell Healthy home vacuum stopped working. The troubleshooting guide said there could be a problem in the connection at the handle. None of the phillips screwdrivers we have seem to work in removing the screw that holds the handle to the vacuum. What size phillips screw driver should we be using? If the screw is stripped, how can we get it out to replace it since it is not easily accessible in the handle?


You should use a p2 size phillips. there is only one screw right in the center that holds the handle assy on. frequently that screw backs out and allows the handle to slide back and loose connection. make sure the handle is tightly pressed in and the ... Vacuums

Low suction Have a Powr-Flite PF 18, suction is good at motor, but low at where hose comes out of top of vacuum. Could new lid seals help the problem? Where can I get new seals for this model. Also my zip is 98801 and my shop is not listed, could you add it please? Sew Creative 1139 N. Princeton Wenatchee, Wa 98801 509-663-5516 Thanks, Lauren-Sew Creative


Replacing the motor cover solved the problem, it must have been warped and was letting suction out thru it. ... Vacuums

My vacuum will not engage to unlock to vacuum. I turn the vacuum on - that works fine. I put my foot on the part to make it so I can vacuum and it will not unlock. What could be the problem. SOO frustrating!


Hi there,I'm sorry to hear you're having difficulties with your DC28. The cleaner should recline easily into the vacuuming position when one foot is placed on the cleaner head, and the handle is lowered. If it's not doing this, check the clea ... Dyson DC28 Animal Bagless Upright Vacuum

My Bernina 807 set on min. speed takes off fast, doesn't go slow at all, although there is a difference in the slow speed setting and high speed setting if I switch from one to the other while stitching. The machine is well oiled and goes well apart from this. I would like min. speed to start smoothly and slowly. I have read it could be capacitor in foot, but DH says it does not look burnt out. Would it help my problem to remove it? thank you, Barbara


... Vacuums

Vacuum e series works on low but not on high


It is either the switch or the controller. Call us and we can see if it is still covered under your warranty.RainVacwww.rainvac.com ... Rainbow E series Canister Wet/Dry Vacuum

Oreck XL upright - has a 2 speed switch. Now only works in high speed not low speed. Will a new switch correct or is it the motor


Your vacuum is fine. The switch can either run at full speed or half speed. You are running at full speed, you need a new 2 speed switch. You can pick them up at an Oreck Store for $29 or around $15 on eBay ... Oreck XL Ultra Bagged Upright Vacuum

Have problem with mine my Z8280 Electrolux vacuum cleaner. It has stopped working. Did all the trouble shooting cleaned everything even though this had been done previously. Turned it on and it only worked for a few minutes and then stopped.


... Vacuums

Have problem with mine my Z8280 Electrolux vacuum cleaner. It has stopped working. Did all the trouble shooting cleaned everything even though this had been done previously. Turned it on and it only worked for a few minutes and then stopped.


... Electrolux Vacuums

The low speed for bare floors won't work at all. The regular speed for vacuuming carpets turns on but spits items back out after a little bit.


There is only one speed on a central vacuum. The power nozzle motor has nothing to do whether or not you have suction. Sounds like you don't have any suction. Unplug your hose from the wall. Start at the unit. Short out the two low voltage wires atta ... Electrolux Central Vacuum

My Rainbow E2 has been working great for years now, but recently it has stopped working on the vaccuuming setting, but will still run on the low speed air cleaning setting. I hope it is something as easy as replacing the switch. Would appreciate any tips to determine if that is the issue or possibly something larger. Tks in advance for the info/help.


Still need help, let me know.\012\012Thank you,\012Ralph ... Rainbow E series Canister Wet/Dry Vacuum

The telescoping wand on my kenmore magic blue cannister vacuum stopped working shortly after I bought it a few years ago. After 10 minutes of pushing sometimes I get it to work. It gets longer easier than shorter. What could be causing this problem? Please help!


... Kenmore Magic Blue 24195 Bagged Canister Vacuum

I had to change a cracked boot. The new part did not have the same pieces even though everything went together again. Now the vacuum turns on, the beater power head works but the vacuum won't stay on. What could be wrong?


It sounds as if they sent you the wrong parts, contact Kirby, let them know your dilemma they usually pride themselves on their customer service. ... Kirby G4 Bagged Upright Vacuum

Roller Brush How do I install the roller brush. I didn't pay attention when I removed it and now when I attempt to vacuum my low carpet it doesn't seem to be working. The green light on the head of the vacuum goes out when I click it down to the floor. It didn't used to do that. Plus I think I smell something burning. Could the belt be broken?


Try a new belt. The ends of the brushroller are different sizes, so you can't put it in backwards. There are numbers and notches on the ends of the brushroll. These notches/numbers need to match on both sides when installing it. (probably need b ... Kirby Ultimate G Bagged Upright Vacuum

Hunter Fan model # 27185-060 - Fan high speed does not work - only get low speed by use of the remote- how do i fix this ???


... Vacuums

My vacuum has stopped working and shut off in the middle of vacuuming. What could the problem be


No power, plugged/jammed impeller. some newer ones have a sensor that turns it off when it is full of dirt... ... Hoover Elite Rewind Bagless Upright VacuumVacuum

Henry vacuum high low switch does not work on low


... Vacuums

Rainbow e2 2 speed vacuum shuts off after 5 minutes of vacuuming.


2 speed E2 models have a circuit board inside that controls the machine. It sounds like this controller board may be bad. The unfortunate part of this is that the board is not only very expensive, but it is only available from an authorized Rainbow s ... Rainbow E series Canister Wet/Dry Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1735 seconds