Having problems with your Rainbow E series Canister Wet/Dry Vacuum ?

Latches how do you replace the latches


Answers :

Use a small punch and hammer to remove the brass pin holding in place. \012The pin has a smooth side and a rough side. The rough side bites into \012the plastic to hold the pin in place. Punch the pin from the smooth side\012 to remove.
RainVac
www.rainvac.com
800-523-0510
Repair Help & Product Troubleshooting for Rainbow E series Canister Wet/Dry Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Foot latch is broken. need to replace with new one. how does one access to remove the foot pedal latch. By foot latch, I mean the foot lever that releases the upright to lower the handle and begin vacuuming.


It is accessed from the bottom underneath by the rear wheel. However, If there are and cracks on the pedal release socket area then the base will need replacement. parts are little cost but the unit needs to be completely disassembled. ... Hoover U6446-900 WindTunnel Bagged Upright Vacuum

Latches how do you replace the latches


Use a small punch and hammer to remove the brass pin holding in place. \012The pin has a smooth side and a rough side. The rough side bites into \012the plastic to hold the pin in place. Punch the pin from the smooth side\012 to remove.RainVac ... Rainbow E series Canister Wet/Dry Vacuum

Electrolux epic replace broken wand latch


... Electrolux Vacuums

The foot latch that holds my Bissell 3596 is broken. Can it be replaced or repaired?


... Bissell CleanView 3596 Bagless Upright Vacuum

Bottom plate latch needs to be replaced


... Sanyo Performax SC-U126 Vacuum

DC07 DYSON REPLACEMENT HOSE. HOW DO YOU REMOVE IT FROM THE HANDLE. I have a kenmore whispertone 8540 canister vaccum. The electrical wires (3) to power the beater are embedded in the hose, in a spiral fashion. The yokes that hold the hose on both ends (and attach to the beater on one end and the unit on the other) have no screws or pressure latches; i don't want to use brute force as i may damage the attachment device inside the yoke. If someone can tell me the trick to get these yokes off each


Should be a pry off dot on the underside revealing a screw ... Vacuums

We have a Bissell Powerwash 1690 with a broken "Latch assy dirty (bottom) tank. Bissell state a replacement part is no longer available. Does anyone out there have a spare or one off a defunct powerw


Sorry, we no longer have this part available for this unit. If you are interested in a new deep cleaner you can use one of these coupon codes currently to get $10 off a machine up to $99.99, or $20 off a machine priced $100 or more. The codes are S ... Bissell Vacuums

The bag latch on my Kirby Generation 3 broke. How do I get the old one off to replace it


At the bottom of the bag, there is a zip tie around the plastic part that turns & snaps on to the exhaust hole of the vac. also take a flat screwdriver & pull up the rubber under the zip tie...all the way around, like u would take a bike tir ... Kirby Generation 3 Bagged Upright Vacuum

The vacuum leaks dust around the joint between the bag and the vacuum. I unlatched the bag, removed and emptied it, and replaced it. However, the vacuum still leaks dust around the joint and the bag keeps working loose. How can I make sure that the bag is securely latched so that it does not leak or come loose? I have no manual. Thanks.


... Bissell 3065 Power Partner Vacuum

Kenmore Model 116 28014700 intuition vacuum cleaner. Latch for hose connection to cannister broke. I have the new part. How do I remove the hose from the broken part and replace it on the new part? I have already purchaed the new part p/n KC92PDDUZV06 for this, bt can't figure out how to get the old part off. It looks like you must destroy old part in order to get it off.


... Vacuums

Clear plastic cover doesn't latch, is there a replacement ??


The dirt cup is only available as a complete unit. You should be able to order one from your nearest dealer. ... Hoover S2220 Flair Bagless Upright Vacuum

I broke my kirby generation 3 vacuum cloth bag latch i found where to get the part but how do take it apart to replace it


... Kirby Generation 3 Bagged Upright Vacuum

How do I replace the plastic latch on the rear of the cannister vacuum? It attached to a cylindrical bar, but it has to go on a certain way to adjust the metal roller underneath.


The plastic handle release just snaps on top of the height adjustment rod on the bottom all you need to do is make sure that the height adjustment rod snaps into the groove. To remove the height adjustment rod just pop out with a flat head screw driv ... Kenmore 25512/ 25513 Progressive Canister Vacuum

Kenmore Model 116 28014700 intuition vacuum cleaner. Latch for hose connection to cannister broke. I have the new part. How do I remove the hose from the broken part and replace it on the new part? Thanks


Hi\015\012\015\012To remove the broken part from the latch use a small screwdriver to release the tabs on the latch on the connector. When latches are released the latch assembly and the plate will slide out of the connector. When the pla ... Kenmore Vacuums

How do i replace the recovery tank latch - Bissell SpotBot Robotic Wet/Dry Vacuum


... Bissell SpotBot Robotic Wet/Dry Vacuum

Broken canister latch


Http://geeksquad.fixya.com/ThreadView.aspx?prdid=414813&thid=604237\015\012Broken canister latch\015\012Posted by nestara on May 17, 2008\015\012The little plasti ... Eureka 431A Optima Bagless Upright Vacuum

Shop Vac lid will not securely latch. 1


Are you sure that the filter is pushed all the way to the bottom of the container? Just take it out and put it back and make sure the filter retainer is gently turned all the way. ... Shop Vac Vacuums

How do I remove the bottom cover on powermate #26412690 to replace belt?


... Kenmore Vacuums

Steamvac F5914-900 Tank Release Latch


... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

I Have two questions concerning my AIRVAC AV2500 Red Series Vacuum System. How do you replace the light in the floor power head sweeper and can you replace the permanent fabric filter? We had the system installed in 2004 and the light in the sweeper head just went out and can not find any manual on line on how to replace it. The filter if not torn but avter 6 years it probably needs some kine of cleaning or replaced even though it says permanent. Any help would be appreciated. Jim McCluskey


... Vacuums

Bissell 6035535 & 2035538 latch assy


... Bissell 1695 PowerSteamer Vacuum

The Footpedal latch won't keep the handle up.


Contact your local Hoover Warranty center and give them the model, they will be able to either ship you the part or sell it to you ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Dear Sir or Madam, I own a black 23 x 47 x 7 mm Rowenta lighter. It has a screw on bottom that I cannot remove. What is it hiding ? Is this lighter refillable ? Is there a flint to replace ?. I've found on your site the following : "By jbbiii on Apr 06, 2009 Father died and left me a Rowenta lighter purchased in Stutgart in 1952. It has a screw on bottom with spring to replace the flint, but I cannot figure out how to open the bottom to replace the cotton wadding which I can see through the hole


Hello \015\012The flint should be near the striker.Or the thumb roller,usually below it.\015\012As old as it is you may not see it beacause its worn down.\015\012\015\012Maybe taking it to an antique store or a smoke shop woul ... Vacuums

I have a Kenmore Progressive model 116.22812204 purchased 2003. The swivel (part nuumber 8195133) that attaches the extension wand to the power mate attachment snapped, so I can't keep the parts connected. I can order a replacement part on-line, but I don't know how to replace it - is it difficult to take apart the power-mate and replace this part? Do you have instructions on how to do it? Thanks!


... Kenmore Vacuums

My older Dyson DC14 (the purple one) early model with a clutch on the beater bar belt needs a clutch replacement. The bar has been cleaned and there are no worn or damaged parts so I conclude that the clutch at the motor end of the belt needs to be replaced. I can find the part online but no instructions on how to disassemble the vacuum to get to and replace it. Dysons only advice is to give me the address and phone of the nearest service center. Can you help me?


Have a look at www.dysonmedic.com which has some very useful info on dismantling and repairing Dysons.\015\012\015\012Although this site doesnt actually cover the DC1 ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0329 seconds