Having problems with your Rainbow E series Canister Wet/Dry Vacuum ?

Vacuum works on low but not on high

\015 Yes\015

Answers :

If it doesn't turn on at all in the high speed mode it's most likely a faulty switch.
Repair Help & Product Troubleshooting for Rainbow E series Canister Wet/Dry Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

The Rainbow vacuum doesn't work on high speed, though it will work for low, what could be the problem?


... Rainbow E series Canister Wet/Dry Vacuum

Low suction I have a Hoover central vacuum system. I've reset the fuse box, checked the fuses, all of the lines are clear and there are no holes for escaped air to travel out. The filter has been cleaned as well. The vac works well with high suction when hooked directly to the unit, however when using any of the indoor connections there is extremely low suction. The machine still turns on so I do not believe it is an electronic issue. I have troubleshooted the issue as best I could and would


... Hoover L2310 GUV Central System Vacuum

Henry vacuum high low switch does not work on low


... Vacuums

Vacuum e series works on low but not on high


It is either the switch or the controller. Call us and we can see if it is still covered under your warranty.RainVacwww.rainvac.com ... Rainbow E series Canister Wet/Dry Vacuum

I was vacuuming with the regular nozzle and all was well. Then I changed to the powered nozzle and the 2nd power level wouldn't work and then when I detached the powered nozzle I was unable to turn it ....there was no suction. The lights are on for low and high level but not middle level power.


... Hoover S3765-040 WindTunnel Bagless Canister Vacuum

Vacuum works on low but not on high


If it doesn't turn on at all in the high speed mode it's most likely a faulty switch. ... Rainbow E series Canister Wet/Dry Vacuum

I have an electrolux renaisence vacuum. the brush in the floor attachment turns but I have no suction. When I change to bare floor option on the handle the brush stops turning (correct) but I still have no suction. The lights on the handle showing --floor,carpet, high and low all work.


Sounds like you have a clog, either in the hose or the inlet by the brush roll. ... Vacuums

Need instructions for 8qt pressure cooker, model 65999. All it has on lid is a dial which says 'open', 'low', & 'high'. If it had a pressure guage it wouldn't be a problem, but I have never worked with a pressure cooker with a low - high dial. Please advise.


Hello. Here is a complete set of generic pressure cooker instructioins http://missvickie.com/workshop/stepbystep.html\015\012\015\012J. ... Vacuums

Brush Roll belt stops turning durring vacuuming on WindTunnel self-propelled, v belt is a little loose with handle down. Tensioning roll is engaged OK, but fully at the end of its travel. Replaced belts flat and v, but still stops turning even on high carpet setting when vacuuming. Carpet setting and height adjustment appears to be working OK, roll is clean and turns easily when out. Also turns easily until it engages the carpet. Self propel function works just fine.


... Hoover U6485900 Bagged Upright Vacuum

On my hover U6616-900 the self propell work fine on the med setting on med height carpet, but when I go to low height carpet and height set on med the self propell does not pull the vacuum and it is hard to push. Also if I raise the height to the highest setting the self propell works correctly and appears to clen. Any ideas? S/N 090400184555, think this vacuum is maybe 5 years old and my wife uses it lots. Should I think of maybe a complete overhaul or a replacement at this time?


This is a typical problem you are describing. I would recommend you change the belts, this will resolve the "hard to push" and most likely resove your issues. based on the s/n given you maching was made on sept 2004. ... Hoover U6616-900 WindTunnel Bagless Upright Vacuum

Vaccum is making a loud high pitched sound, doesn't work well through the hose or the floor piece and shuts its self off after about 5 minutes. I have cleaned the entire vacuum out several times but this problem persists. Usually after I clean it, it'll work for a couple months, not this time. Vacuum is only 2 years old, is this typical?


... Dirt Devil Featherlight Bagless Upright Vacuum

My rainbow vacuum will not start in high speed but runs in low speed


Yes, it sounds as if your controller is bad. Give us a call and we can see if it is still covered under your warranty.RainVacwww.rainvac.com800-523-0510 ... Rainbow E series Canister Wet/Dry Vacuum

I have the eureka capture vacuum and it works great; however, it has recently started making an extremely high pitched sound when I use it. It is still vacuuming but the noise is so loud it hurts my head and I can only vacuum for a few minutes at a time before I have to turn it off. What is wrong with it???


Dust is getting past the dust cup filter, to the motor. Call Eureka customer service. 1-800-282-2886. ... Eureka 12 Amp Capture Vacuum Upright Vacuum

Vacum works on low but not on high??????


Ur rainbow cumpiter has 8 years warranty call Rexair and give them ur seriel # u should be covered under warranty ... Rainbow E series Canister Wet/Dry Vacuum

Motor quit working. i was vacuuming and all seemed fine. then the motor went really low. when I opened it I noticed that the bag was not attached and the cannister had filled up with stuff and the filter was full. the vacuum will not run now.


My friend, the dirt you sucked up went right into the motor and it burned up. I am very sorry to tell you this. It is probably not worth repairing unless you are able to replace it yourself.\015\012\015\012In addition to not being able ... Kenmore 31912 Progressive Direct Drive Bagged Upright Vacuum

Roller Brush How do I install the roller brush. I didn't pay attention when I removed it and now when I attempt to vacuum my low carpet it doesn't seem to be working. The green light on the head of the vacuum goes out when I click it down to the floor. It didn't used to do that. Plus I think I smell something burning. Could the belt be broken?


Try a new belt. The ends of the brushroller are different sizes, so you can't put it in backwards. There are numbers and notches on the ends of the brushroll. These notches/numbers need to match on both sides when installing it. (probably need b ... Kirby Ultimate G Bagged Upright Vacuum

Vacuum height won't go on low carpet setting. Dial will go on medium and high, but not low.


Make sure you're not trying to adjust w/ handle in upright locked position because thewre is a cam which raises the vacuum head a little bit when handle is locked in upright position. If this is not the problem, turn vacuum upside down with handle in ... Hoover Vacuums

The e series rainbow 2 speed works only on low speed. High speed will not run. What is srong?


It is either the switch or the controller. Call us and we can see if it is still covered under your warranty.RainVacwww.rainvac.com800-523-0510 ... Rainbow E series Canister Wet/Dry Vacuum

No spin Vacuum's brush does not spin on (low) carpet unless switched to "high" but then roller does not pick up hair on carpet. Belts are in good condition. Maybe belts are loose?


Http://geeksquad.fixya.com/ThreadView.aspx?prdid=40485&thid=782631\015\012No spin\015\012Posted by erin_david on Jul 14, 2008\015\012Vacuum's brush does no ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

I have an Electrolux Commercial Upright vacuum Model U129C. It has a device which turns off the motor driving the beater bar if something gets stuck in it. There is a simple reset button to restart the beater after clearing the obstruction. Just recently on flat dense low pile surfaces the switch cuts in after just a few seconds and turns the beater bar off. This doesn't happen on high pile carpet but the motor doesn't quite sound normal. There is no obstruction - the beater bar can spin freely


The motor is having a problem.There might be two reasons...either the coils inside it got heated up which will be needing rewinding or you can buy a new motor or there r capacitors attached sometimes u can make a check on that also if that's gone Kap ... Vacuums

Hunter Fan model # 27185-060 - Fan high speed does not work - only get low speed by use of the remote- how do i fix this ???


... Vacuums

My vacuum is working but makes a really loud high pitch noise when it is turned on.


Vacuum motor is more than likley going out ... Bissell Vacuum - Momentum Cyclonic 1 ea Bagless Upright Vacuum

Oreck XL upright - has a 2 speed switch. Now only works in high speed not low speed. Will a new switch correct or is it the motor


Your vacuum is fine. The switch can either run at full speed or half speed. You are running at full speed, you need a new 2 speed switch. You can pick them up at an Oreck Store for $29 or around $15 on eBay ... Oreck XL Ultra Bagged Upright Vacuum

The low speed for bare floors won't work at all. The regular speed for vacuuming carpets turns on but spits items back out after a little bit.


There is only one speed on a central vacuum. The power nozzle motor has nothing to do whether or not you have suction. Sounds like you don't have any suction. Unplug your hose from the wall. Start at the unit. Short out the two low voltage wires atta ... Electrolux Central Vacuum

I have a lakewood fan hv20cr fan and it will only work on high speed. low and mid spin very slow with a bad hum. How can I fix it? where can I get parts for it.


... Lakewood Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0699 seconds