Having problems with your Rainbow E series Canister Wet/Dry Vacuum ?

Series e best way to remove a frozen ariater nut


Answers :

First purchase a new aerator nut and aerator. Now spray where the nut meets the separator liberally with liquid wrench , let soak for an hr or 2 and then take a tooth brush to it at the same place. Don't try loosening it with a screw driver , use a deep well socket. Sorry I don't remember what size. if this doesn't work you can try a torch. To prevent this in the future thoroughly dry the tank after washing it and store with the aerator and nut OFF .
Repair Help & Product Troubleshooting for Rainbow E series Canister Wet/Dry Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Series e best way to remove a frozen ariater nut


First purchase a new aerator nut and aerator. Now spray where the nut meets the separator liberally with liquid wrench , let soak for an hr or 2 and then take a tooth brush to it at the same place. Don't try loosening it with a screw driver , use a ... Rainbow E series Canister Wet/Dry Vacuum

The nut on the seperator on my e series is frozen on , how do I get it off and can I use the e2 series seperator on an e series. Aparently the e series nut and seperator had to be take off more often or it freezes on...I bought a used one that's stuck and It works but I can get the seperator off to clean.


Do you have a friend who is a car or motorcycle mechanic? The acorn nut you refer to can be removed with the use of a small air impact wrench. Make sure the wrench is set to REMOVE (anti clockwise) the nut and give it a short burst. Never fails. ... Rainbow E series Canister Wet/Dry Vacuum

Carpet Removal I need someone to tell me what is the best way to take up or remove carpet.


Cut it into two foot strips with a utility knife for easy carryout, then if you need to remove the tack strip as well use a pry-bar but be careful as the tack strips are very sharp ... Vacuums

What's the best way to remove wax off a tile floor?


With goop brand remover will take almost anything off without damaging the tile ... Minuteman C46000-00 Self Contained Carpet Extractor Vacuum

Hi, So glad I've found this site! I've attempted to remove the filter as per this post: http://www.fixya.com/support/t2784981-remove_filter_beam_model_2775 The result is that I've pulled off the finger loop because the filter was in so tightly. Please can you tell me what the best way forward from here is? Thanks, Duncan


So did the filter itself come with it, or just the finger loop broke off and the filter is stuck in there? :(Tim ... Beam Industries 2775 Serenity Plus Central System Vacuum

Cannot remove the brass nut for separator on rainbow series e


... Rainbow E series Canister Wet/Dry Vacuum

What's the best way, if any, to clean the carbon deposit on the E Series armature?


Use a scouring pad, or emory cloth. Do not use sand paper, or a wire brush. That will cause too deep of scratches, plus you may get sand in the motor components, or damage sealed coil wires, and ruin your motor.\012Let me know if you have any m ... Rainbow 75th Anniversary Canister Vacuum

Can't reassemble!!! Long story as short as possible- I removed the hood from my Bissell 1699 and can't seem to get it back on correctly. The "Smart Mix" knob and it's parts seems to be the problem. How does this line-up, or what is the best way to put it all back together? Thanks, Josh


The piston is put on the bottom of the smart mix knob, turn the knob to the water only setting, then put the top housing back in place making sure that the piston went into the slot, after the top is all of the way down, turn the knob, if it turns ea ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

Where can I order the following parts for my 1952 KENMORE SEWING MACHINE MODEL #117583, SERIAL #48054: : #5107 carbon motor brush (2) #5110 motor brush spring (2) #5111 motor brush spring cap (2) String for starter control lever Pulleys, screw and nut washer to attach string control Best sewing machine ever and still working like new, and I want to keep it that way. Thanks.


... Vacuums

How do I access the motor to my eureka capture? It has no suction at all but turns on just fine..filters are cleaned and there are no clogs or leaks on the hose....im thinking there must be something stuck in the motor possibly but there are soo many screws that im having trouble removing them all....whats the best way to access the motor to check it??


... Eureka Capture Upright Vacuum Vacuum

How do i remove the canopy of my hampton bay ceiling fan? I want to relocate it and there are no screws or nuts visable on the outside. I've tried turning both ways and it gives a little but the whole fan moves when i turn it. I've tried pulling down even prying it from the ceiling. Nothing works. HELP!


HI!!\015\012\015\012I assume you've removed the blades. so next step is to check the canopy. The Ceiling Fan canopy has a decorative ring RIGHT against the ceiling that covers some screws. Remove the ring, remove the screws ... Vacuums

I have a Rainbow E series. The separator is broken. I removed the acron nut but the separator won't come off. Is it ok to pry it off from bottom?


It's ok to pry on it if you're careful. Tap it too, use a screwdriver handle and just go around it and tap judiciously. When you're prying, be sure that if something is going to break it's the separator and not the machine housing.Clean t ... Rainbow E series Canister Wet/Dry Vacuum

Bissell proheat 2x 9200 series carpet cleaner. I need to remove the Brush Drive motor. However, this series has the gear end of the motor shaft poking out a hole on the left hand side. I removed the retaining washer and pin from the gear shaft. I need to get the gear off of the shaft in order to remove the motor. It's not budging. How do I remove the gear so I can pull the motor out of the unit? Thanks .


Chap, I wish someone had answered this. I'm having the exact same issue. ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Unable to remove round filter in bottom due to bolt not secure inside vacuum and it is just spinning so I can't remove nut holding on filter, but cannot see how to remove top of vacuum to get at other end of nut.


If you are talking about the acorn nut that secures the separator to the motor shaft, it can be removed with a small (or even a big, for that matter) air or electric impact wrench with the proper sized socket. Find a mechanic friend who has one, make ... Rainbow E series Canister Wet/Dry Vacuum

After removing the filter, I cannot get to battery on the Dirt Devil Kone M0213, there are two horizontal screws. Removing them does not help getting to the battery, no way to remove the insert where the battery is located.We have two of these, however they did not come with a manual for dis-assembly. Please help or proved a diagram on how to remove the battery. Many thanks, Wesley Lennon


Sheesh, did anyone actually read the person's question? It's about the battery, not the filter.\015\012\015\012You have to get the outer cover off and it's not easy. There are four tabs which need to be released. I have to use a very sha ... Dirt Devil KONE Hand Vacuum MO213BLU Vacuum

Best way to clean a laminate "wood" floor. I use Pine Sol and lately have been noticing streak marks and dullness.


... Vacuums

I havea Bissell ProHeat Model 7901. My problem is that the brush doesn't rotate. I have removed the access cover and both belts and found that the central cylinder for both belts is frozen and will not turn easily. Both belts are fine, except they are now burnt from this cylinder not being able to rotate. What I need is how do I remove the top cover to get at this cylinder to remove it and free it up?


... Bissell 8910 ProHeat Clear View Upright Vacuum

I have a Sears Upright vacuum cleaner, model 116.35922500. The vacuum wasn't picking up. I discovered a clog in the nozzle hose. I attempted to remove the cover of the brush unit to clear the clog. I was unable to remove the cover completely, but was able to clear the clog. My problem now is that I cannot replace the cover correctly. Is there a way to remove this cover? Thanks, Elizabeth


When you tried to remove the cover did you have to put a little force on it to get to the clog ... Vacuums

Trying to attatch the wires from the light kit to the fan but the blue and white wires from the fan have white caps on them covering the wire. Do these need to be removed in order to attach the wires with the wire nuts? If so, how are these white plastic caps removed?


They're called "wire nuts". Turn them counterclockwise to remove, lay the wires you need to join side by side with the ends of the bared sections even and screw the nut on. lp ... Vacuums

IRobot rumba 4000 seems to run ok and then starts making a kinda hi pitched growling noise and slows way down. it is very clean(blown clean with air compressor)sensors are clear ,newly installed well lubricated on ends of brush and beater bar, new battery. it seems like the wheel tracks may be dragging . i have cleaned and lubricated where i could on them but can't find a way to totally remove and inspect wheel tracks.


It sounds like your Roomba's brush gears are not working. Run the robot without the dust bin to see if the brushes are turning. If they are not, the robot will need to be replaced. Contact iRobot CS for support at (877) 855-8593. ... iRobot Roomba 4000 Bagless Robotic Vacuum

Dyson dc07 The rotating brush on the bottom of my vacuum was filled with strings. I removed the brush by undoing all yellow plastic screws from plate. Removed all strings and replaced as best I could and it was hard to get the brush back in and the belt around it. I dont have my manual but it fits so it should be correct....? Right? No, not true, because when I turn it on and try to and vacuum (by lower canister with foot release) it makes that terrible ratching sound). Please help


The loud ratching is a warning to tell you that there is something stopping the roller bar from rotating this is a very common thing lay the machine on the floor front side down take off the bottom plate and just check the belt is in the centre of th ... Dyson DC07 Bagless Upright Cyclonic Vacuum

My DC 17 is plugged. I can see through the small hole in the top blue "flower shaped" that the holes at the top of the canister are plugged with hair & dirt. I cannot see anyway to get to these small round holes. Is there a way to remove the top blue "flower shaped" piece? I have removed the inner cone from the clear canister but still cannot get up underneath.


Please kindly follow the steps below to clean your vaccum cleaner,1.) Remove the clear plastic handle. You\015\012will have to take out two screws and then unclip from the from the\015\012front. It's stiff, I gently used a flat head screw drive ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

I have a Panasonic MCV7515 UPRIGHT VACUUM and need to remove the cowling that covers the brushes to clean the hair out of the bearings, but it isn't clear how that can be done without a crowbar or sledgehammer. Removing all the visible screws makes the hindmost part loose, but not the front half. Also, is there an easy way to replace the belt?


... Panasonic MC-V7515 Bagged Upright Vacuum

I need to find a way to replace the attachment hose on this unit. the tube to spray the detergent snakes into the base next to the wheel and i'm unsure of how to take it apart without breaking it. is there a simple way to remove the wheel? do i need to do something special to replace that tube?


The best thing for that situation is to look on the side of the road and you will find a Bissel, I see one or two a week. Take one home and experiment on that one not yours. I have brought many and never have I bought one. I never see a Hoover by ... Bissell 9200 Upright Vacuum

Model UH60010, Series X12.0, Mfg code K09A. While attempting to use the hose and the extensions to clean shelves, my wife reported no suction. I removed the brush roller and the plastic piece just below where the hose opening is located and saw a "flapper" door that was closed and had some debris sort of jamming it. I removed the debris, but the door requires extreme pressure to open to permit the dirt, etc to moved up thru the opening , through the hose, etc. I thught maybe that somehow tg


Hello,Check to make sure\015\012the dirt canister is empty. If dirt canister is full, then you will \015\012experience\015\012reduced suction. Empty dirt receptacle.\015\012 Could\015\012 be a clogged hose - ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0367 seconds