Having problems with your Rainbow Technologies D4 Bagless Vacuum ?

Can not get the housing off

\015 How do you take off the housing of a d4c rainbow vacuum cleaner?\015

Answers :

Remove the 4 screws on the bottom of the canister, and also carefully remove the water basin gasket. You will reattach the gasket with rubber contact cement when you're finished with your repair/cleaning.
Repair Help & Product Troubleshooting for Rainbow Technologies D4 Bagless Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Have Electrolux 1590 whole house vac, and can't see how to get brushes out. Leads so short, and don't want to break them trying to free brushes. Do they slide out of plastic housing? My eyes not real good, but it looks like the leads are part of a brass sleeve that slides into the plastic housing. It also looks like the plastic housing may be a snap lock type, but I don't see how to open it.


... Electrolux Vacuums

I need to change the motor in a vax 6131 but i don't know how to get into it to get the change it? I also need to get into the motor assembly housing to change a part but can't see how it comes apart!!


On the handle there is one small pozidrive screw, remove and orange panel comes away revealing powercable securing bar. Remove 2 screws and this reveals a 10mm headed bolt. Under label on top of handle there is another small pozzi screw, undo t ... Vacuums

Vorwerk VK121 vacuum cleaner - smell of burning from housing enclosing motor. How do I get into the housing to inspect the motor? After tilting the bag sideways, there are two screws holding the housing visible, but there seems to be a thrid fixing inside the point where the handle shaft is attached - is the handle simply clipped in place? Thanks


Yes the handle is clipped in place and should come out when the button in front is pushed. Remove the screws you wrote about. After that the puzzle begins. At the bottom of the vacuum where the head is attached, remove the head by pressing the but ... Vacuums

A baby sock was sucked up and stuck where i can't see it in my regina electrikbroom cleaner - 11.4 amp. i have tried to get it out and now i have to take it apart i think and can't get the housing apart - what should i do?


... Regina ElectrikBroom RG100 Vacuum

Whistling noise I just bought Dyson dc 33 multi floor plus about a month ago and use it 6 times because the carpet get dirty / dusty so quickly living with 5 other people in the house and when I use it today by stepping on the foot thing to make it to go down and when I push the botton it makes the whistling sound why is it like that I have read every instructions several times , does that mean I need clean the filters or need to get it fixed . When I first used the vacuum it was not like that a


... Dyson DC-33 MultiFloor Upright Vacuum Cleaner

Help! i have a whispertone 300 model 116 28612790. the retractable cord is jammed & i could only get the front part of the canister open that houses the motor, etc. there are only 2 screws to open it & i can't get it off to fix the cord. hope this makes sense. thank you!


Even if you get it apart chances are it needs a new spring but it requires a special tool to get the rubber molding off that separates the top from bottom and sears repair guys and vacuum shops have them. I would take it to a used vac store and get t ... Kenmore 23313 Whispertone Bagged Canister Vacuum

Cleaning Filter Hi: I want to clean the filter on the B&D pet hepa vacuum, but can't figure out how to take it out of its housing. I can remove the housing from the actual vacuum, but don't know how to get the filter itself out. It sure does smell of dog, so any help would be appreciated.


... Black & Decker Black Decker Bagless Canister Pet VacVacuum

CAN'T GET THE BELT OUT, TO REPLACE. IS THERE AWAY TO GET THE HOUSING OFF TO ENABLE A BETTER VISUAL TO REPLACE


It helps if you have the Dyson Belt Change Tool. You can get one here:Dyson Belt Change Tool ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

To : admiralstopf I have a U-Line clear ice maker UCLR2060B40. The authorixed service center has been trying to fix my unit since October to March. They have replaced the circuit board 2x and the Thermister and rain tube. They clai they were able to get it to work on their bench (not sure if true) but they can not get it to work in the house. They gave up and refunded my payment. Now what? Jonathan


Unfortunately we are not affiliated with any manufacturers. What I would do at this point is to contact the manufacturer of your ice maker and let them know what has transpired when you attempted to have their authorized repair center fix your issue. ... Vacuums

I just moved into this house and it has a broan cv40-d central vac that i can't get to work it turns on and that is about it i have no owners manuel so i am lost as to what to do any ideas or owners manels available? I can't even get the bottom off after releasing the clasps


... Vacuums

My Kirby 2HD has started making an odd roaring noise but still works fine. I have taken the front assembly off and cleaned and adjusted the roller and checked the belt. The noise seems to come from the motor housing. I have tried to wiggle the main shaft at the front (bearings?) and it seems tight. Can't seem to get the other housings apart. Any ideas? Thanks, John


It is quite possible, it just needs lubed. The motor comes in direct contact with dirt so, you have to make sure the front bearing has a drop of oil on it from time to time. If it starts to scream at you within one month, after oiling, the bearing ... Kirby Heritage II Vacuum

Hi, i am mike. i have a bissell model #6585. the power cord has broken off from the housing. h;;ow do i get the housing apart to reconnect the wires. thank you


Hi Mike! You'll want to contact one of our Authorized Service Centers to have one of our techs inspect your vacuum.\015\012Here's a quick link: http://www.bissell.com/service-centers/?cid=ccsocial ... Vacuums

Replacement parts... I've got a 3594 Bissell and the belt has come completely off. In the process of breaking, it bent the metal guide inside the motor housing and melted the plastic that holds the guide and keeps the belt inline with the roller. I've got it running again by using a screw I filed all the threads off of, but it only works for 10 minutes at a time before breaking another belt. This process is getting expensive, as it usually takes 30 minutes to completely vacuum the house. Is ther


Most likely it is the top cover that needs to be replaced, part #2031238 and is around $30. It would have that guide on it. ... Bissell 3594 CleanView PowerTrak Bagless Upright Vacuum

U-Shaped piece I was in the hospital for a couple of nights and my 80 year old mother decided to go to my house and vacuum my house. When I went to get it out to vacuum the other night the u shaped part fell off. I guess my mom had somehow knocked it off. Now I cannot figure out where it goes. It is a plastic U-shaped piece. Can you help me? I sat for a hour trying to figure out where it goes.


It attaches at the bottom of the hose and goes into the bottom of the valve. Located on the back bottom of the unit. ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

I have a Hoover Elite Rewind vacuum. Actually,this is my second one. However, after about 4 months of use, it emits a "sour" smell when I'm using it. I empty the cannister before each use and clean out the filter monthly. My house has mainly hardwood floors, so I typically only use it on area rugs and 2 small carpeted rooms. Is there any way that I can get rid of the smell? I've tried putting a dryer sheet in the cannister, but this gets stuck in the filter mechanism. Also, carpet fresh clogs th


Does it smell like an electrical burning odor? could very possibly be the motor going bad already. ive seen it happen. but if not try freshwave odor absorbing pearls. i carry it in my store and we do have shipping. Truly the only thing you should use ... Hoover U5507900 Elite Rewind Bagless Upright Vacuum

Samsung Quiet Storm Canister Vacuum VAC-9049 The motor will not run. Power is on to the motorized rug tool. How can I remove the upper housing to get access to the motor? I have removed the six visible screws, but the housing is restrained at the rear. I suspect there are additional screws under the power switch and cord retractor assembly, but I cannot remove that either. HELP!


Hi Daltm,\015\012Thank you for contacting Fixya. This is Anil.\015\012I understand that you need assistance n opening the Samsung Vaccum VAC-9049 motor. I will be glad to help you with it.\015\012Please go through ... Samsung Quiet Storm 9048R Bagged Canister Vacuum

Kenmore/Sears Progressive 116 How to get housing off to replace cord


There are four screws, two at the front and two at the back under the step bar that rewinds the cord.  It lifts off from the bottom.  Be careful not to snap off the tabs. ... Kenmore 23913 Progressive PowerMate Bagged Canister Vacuum

Vacuum got left in the rain, can't get housing apart


Remove any screws you see on the top rear panel. Take off the filter to reveal another screw. The control panel across the back look between the lid and that panel, there is another screw there. On the very back there is a black strip that helps h ... Miele S251 Flamenco II Bagged Canister Vacuum

Can not get the housing off


Remove the 4 screws on the bottom of the canister, and also carefully remove the water basin gasket. You will reattach the gasket with rubber contact cement when you're finished with your repair/cleaning. ... Rainbow Technologies D4 Bagless Vacuum

How do you disassemble Rainbow D4c to replace power cord? Took four screws loose but unable to see how to get housing loose...


Gently pull on the rubber gasket that seals the water tank to the canister. Although there are more screws under there - they aren't necessary to remove only to replace your cord. It is the gasket that is holding the motor flange and the plastic hou ... Rainbow 75th Anniversary Canister Vacuum

Went to get some water for the Bissell Petwash power brush, when I reconnected it, the water is not coming through the house. The vacuum is working, just not the water.


Try this...... take a part the upper half of the machine and\015\012look for the heater.take off one of the hoses and plow in it to see if it is clogged it is take a part and clean out .\015\012what happens is it gets clogged with soap and wate ... Vacuums

The motor just went out on my 2 year old vacuum with light usage (hardwood floors in a very small house.) The Sears repairpeople are estimating ~ $130 to fix (this includes parts & labor). I'm wondering if it's worth investing $130 into something i've spent $350 on only 2 years ago. Shouldn't these machines last longer ? Is there something I could do to get them repair free as it seems the motor must have been faulty to only have lasted 2 years. Thoughts ?


Aye, get a dyson, if its out of warranty there's not much u can do bout it :( ... Kenmore 25512/ 25513 Progressive Canister Vacuum

This vacuum keeps getting clogged in the hose and has terrible suction. The women who helps clean my house won't even use it as it performs terribly. Any suggestions


Check vac air filter(not the dirt collection bag) also something could be lodged in hose mechanism so there is always a partial restriction. make sure the beater bar is not set too low. check the dirt that accumulates in bag to see that there is no ... Hoover Fusion Plus Cyclonic Upright Vacuum Vacuum

Our Bissell Cleanview II 3576M does a great job except that the filter cup below the dirt cup gets full very fast and the dirt cup barely has anything in it. To clean the whole house, I have to empty the dirt cup and clean the filter several times. It didn't use to work this way. It seems like something is missing, a gasket or seal maybe? I don't think dirt, hair and debris should be going straight to the lower cup and bypassing the upper. I looked at the user guide but can't see why it's happen


Contact Bissell Direct for a parts diagram and support at \015\012\015\012http://uk.bissell.com/EmailUs.aspx\015\012 ... Bissell 3576 CleanView II Bagless Upright Vacuum

I have a dyson dc07 original that i bought used. Last owner was obviously a pet owner and the machine smells too bad to even turn on in the house...can I clean the canister with water? What other parts can get wet or is there a better way to remove the odor?


Put some vac freshner in the canister put the vac out side if its fine plug in and switch on leave runing for around 10 minutes that should solve the odour ... Dyson DC07 Bagless Upright Cyclonic Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0358 seconds