Having problems with your Regina ElectrikBroom RG100 Vacuum ?

I have acquired an old Regina Electrik Broom

\015 I have no product manual, I cannot figure out how it opens to empty it.\015

Answers :

Hi jmathe, Looking at the back (business side) of the vacumn: Underneath the white plastic dirt cup, please find a cast aluminum latch, that secures the part you will empty. To remove the white plastic part, turn the aluminum latch handle downward, and to your right, while you are holding on to the dirt cup with your left hand. I usually wear a dust mask, and empty the dirt into a small grocery bag, to tie shut, before placing it in the trash. To replace the dirt cup, turn the cast aluminum handle back to where it was before, handle pointing left. The more often you empty the cup, the longer your Regina Electrik Broom will last. Mine is forty-five years old. Allow the motor to cool, often, as well.
Repair Help & Product Troubleshooting for Regina ElectrikBroom RG100 Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have acquired an old Regina Electrik Broom

Hi jmathe, Looking at the back (business side) of the vacumn: Underneath the white plastic dirt cup, please find a cast aluminum latch, that secures the part you will empty. To remove the white plastic part, turn the aluminum latch handle downward ... Regina ElectrikBroom RG100 Vacuum

RB5628A Regina Electric Broom - Regina ElectrikBroom RG100 Vacuum

... Regina ElectrikBroom RG100 Vacuum

Can I remove the brush strip from the old Bissell magic broom without damaging the foot? I use it to vacuum up bird seed from my carpet, but the brush seems to hinder more than help! many thanks Anne Precious-wings parrot rescue

... Vacuums

I have a Regina Electric Broom 3.5 and can not figure out how it opens to empty it.

... Regina ElectrikBroom RG100 Vacuum

How do you remove dirt from the regina electric broom

It's not the best design. Grab the canister push down hard while pulling top out. If you look you can see the tab you have to clear at the top. It gets easier the more you do it. ... Regina ElectrikBroom RG100 Vacuum

The serial number is 911 This broom is old, but did not use it much. Cannot find directions that came with it. I need to remove the dirt bag, but cannot remove it. Help. Thanks

... Regina ElectrikBroom RG100 Vacuum

My old Tristar canister vac.

If you have a voltage meter you could see where the problem lies. All TriStar parts including the motors, both the nozzle head motor and the actual vacuum motor are purchaseable online through ... Vacuums

I have a Eureka 4870GZ. It turns on, but the brush roller doesn't move. The belt looks fine. I do have an extra belt and would try replacing the old belt, but I can't get the old one off the motor shaft or the new one on. I called Eureka customer service. The lady said there's supposed to be a small space between the motor shaft and the outside edge of the vacuum where I can slip the old belt off and the new one on. I don't see it. It looks like the motor shaft goes into a recessed place in the

Remove the top cover so that you can access to belt, You'll find 2 rows of 4 decorative holes on the top cover, In two of the holes you'll find the screws, Please use a flash light to see in that., Once the screws are removed, you'll be able to ... Eureka Vacuums

DYson DC07 not sucking properly when in upright mode. I have tried cleaning out pipes etc and even tried an old motor section I had in garage (replaced once under warranty as kept cutting out and they left old motor section here). Even the old motor section had same prob so this suggests its something in the rest of the vacuum cleaner (whats left after you have lifted off the green motor section and dust collection area if you see what I mean? Any advice weclome please.

Blocked filters ... Dyson DC07 Bagless Upright Cyclonic Vacuum

I have an old Friedland door chime (approx 30 years old). It has 5 terminal screws to connect wires. They are labeled 0-4. I removed the chime during remodeling and would really like to reuse it. I did not label the wires and where they connect when I removed it. I can't figure out how to wire it. I contacted Friedman and they were of no help... didn't have information on chimes that old. Can you help with how to wire the chime given it has five connections screws with no labels other t

... Vacuums

My machine (Hoover Wind Tunnel - bagless) is only 1 yr. old. The agitator brush doesn't turn all the time. I know it's not supposed to turn when in the upright position. However, it only seems to work when I have the setting on high. When I stop, but have not put the machine in the upright position, it stops again and then slowly starts moving. Could the V-belt be worn out already? In the owner's manual it states that this belt is not normally replaced. The exact same thing happened with my old

Sounds like you should do two things:\015\0121- Remove and clean the beater brush of all debris as best you can. At the end of the brush you will see a hard rubber piece, at both ends, that holds it in place in the body of the vacuum.\015\012Add som ... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum

I heard that a class action lawsuit against Oreck Vacuum is being started because of all the problems customers are having with their vacuums. Does anyone know about this? My Oreck is only a couple of years old and keeps burning up belts. I took it in after only one week of usage when I started to notice white smoke coming out of it and the smell of burning rubber. I feel like I got the old run-around, when the service tech told me he couldn't find anything wrong (but replaced the burned up belt

You are correct about the fact that legal action has been taken. Go to this link to read more\015\012\015\012 ... Oreck XL2200 Bagged Upright Vacuum

How do i take the old belt off of my dyson dc 14? cant seem to figure out how to get the roller separated from the machine because i cant get the old belt off.

Go to: Dyson web site or \015\012\015\012 http://www.repairclinic.com/0100_24.asp\015\012\015\012There should be 4 to six screws holding the ... Vacuums

I bought an old Juki Baby Lock 418 at a garage sale. It will sew for 3 or 4 inches and then seems to be off timing and locks up. I have no instruction manual. Is there a manual available for this old machine? I would prefer a downloadable manual because I already have money invested in the machine which doesn't seem to work. It was suppose to have been gone over at a repair shop before I purchased it and was told that it worked. .

... Vacuums

Need help in changing the blade on inside of case housing for a old G6 type vac 15 plus yr old. how do i replace plastic blade.

This guide should make it easy for you!!!\015\012\015\012http://reviews.ebay.com/KIRBY-VACUUM ... Kirby G6 Bagged Upright Vacuum

My first proheat lasted four years so I bought a new one. After I used my Pro Heat for only the fourth time my first issue occured, the gear on the pump that runs the brushes came off, so I had the one from my old proheat, I just changed the gear spindle that is screwed to the pump and fixed that problem but now it will not pump water. That is why I bought a new proheat, I could not get the old one to pump even after a new pump and made sure all lines were not cloged.

Is your new machine a 2X or like the old style proheat? ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

Changing a belt on a Hoover Vacuum Cleaner, Model U4264-930. can not get the old belt off.. U4264-930can not remover old belt on sweeper

... Hoover Vacuums

Bissel spot bot water not coming out of tank is not a year old and tried manual wand and the water doesn't come out there either. any advice. Is not a year old yet.

You could take the end of the handle off 2 screws i think check the line for a clog or just take it to a bissell service center it will be covered under warranty ... Bissell SpotBot Robotic Wet/Dry Vacuum

Suction I too have the same problem as Mr. Chief. I followed your advice and checked all the hose attachments, no clog. Tthe only one hose that the broom handle would not pass through was the plastic hose and there is a curve in that part. I did not want to force the broom in there as this is a new vacuum and is probably under warranty.

If you have a plumbers snake you can use that. But being under warranty, I would take it to Sears for repair. ... Kenmore 25614 / 25615 Progressive Bagged Canister Vacuum

How to install a new motor in a filterqueen canister vacuum the old motor was 5 wire and the new is 4 wire. Wire colors are not the same.. - No, I have not disconnected the old wires.

According to my parts house, there's a 4-wire motor for some of the filter queen models and a 5-wire model for other filter queen models.You can still purchase a 5 wire motor. Check out greatvacs dot com. They carry both 4 and 5 wire. ... Vacuums

Need a replacement on/off switch for Dirt Devil Deluxe Model 8201 (more than 12 years old). We have the old one out. We just need a new one to replace it. Where can we get one?

... Dirt Devil Vacuums

Hi There I have got a Kirby 2 HG vaccum cleaner which is around 20 years old now. It was going really well until last week when one of the capacitors which are connected to the brushes blew up. There is two capacitors one for each brush. One of them completely blew to bits and the other one is still intact. My question is are they the same size and where do I get a new one from. I know it is an old machine, but I would like to fix it and get it going again. Any tips???

Http://www.geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=541405\015\012Generic problem for all Vacuums\015\012Hi There I have got a\015\012Posted by opfinder on Apr 24, ... Vacuums

I'm not really a technician, but I used to sell Filter Queens and was taught how to maintain them, and have tackled "fixing" some problems. I am a 71 year old great-grandmother of 8, but have good health and am very active. The Filter Queen I have is r, usedeally old, and I have kept it up. Just this week, however, I turned it on and it had a noise which sounds like something might be loose in the motor. I have always been very careful to have a clean hepa filter to protect the motor, so I know

It's tricky to hold screws with one hand and screwdriver with other hand; however, I am 65-yr-old female and do it yearly with 100% perfection! Take a break, relax, and try again! I sit on floor, put attachment between legs for supporting vacuum, h ... Filter Queen Majestic Canister Vacuum

I have the new power on/off switch to replace the old one(Rainbow vacuum). However the new switch has 4 contacts & the old one has 6. Need wiring diagram.

Simply pair 1 each of the power head leads and motor leads on to one terminal and wire the cord as on previous switch. ... Rainbow E series Canister Wet/Dry Vacuum

Help!!! it is only 1 month old old. making a loud noise especially when turning off sounds like metal on metal.

Motor fan catching motor housing ... Bissell 6594 PowerForce Bagless Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0276 seconds