Having problems with your Riccar 4812 Vacuum ?

I need to remove the motor in my ricar 4812 (to change the axle) Where can i find something on that? I have 4 screws out- but it seems to be held into the body where the shaft goes out to the belt. Just missing something dumb.


Answers :

Repair Help & Product Troubleshooting for Riccar 4812 Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I need to remove the motor in my ricar 4812 (to change the axle) Where can i find something on that? I have 4 screws out- but it seems to be held into the body where the shaft goes out to the belt. Just missing something dumb.


... Riccar 4812 Vacuum

My FIL purchased an Electrolux bagless canister vacuum model EL5 76501 last year. When I tried to use it today, the hose keeps pulling out of the power brush whenever I pull it towards me. it doesn't seem like anything has broken off. The only thing I noticed was that the rubber ring washer seems to be flattened. Could it be something that simple or do you think some part has fallen off and gone missing? Regards, Craig Somersett


I believe I've just had the same problem and after searching for a small gray horsehoe clip that needs to first be found and then inserted into the slot for it on the tube section that comes out of the beater bar. Insert this clip from the outside af ... Electrolux Vacuums

Having cleaned my De Longhi Treviso after storage I am at a loss as to why, when the machine turns on steam escapes from the outlet. It seems as if there is something missing from the pressure vessel behind the spring. Is there anyone who has a schematic diagram where I can ascertain what, if anything has been lost/gone missing.


... DeLonghi Vacuums

I have a DC17 animal vacuum and it is not picking up as well as it used to. It misses small particles on the floor. The hand held piece seems to work ok, but otherwise, it seems to not have as much suction. What should I do. It is only a little over a year old.


It could be that you need a new belt. Over time the belt stretches and wears and then it doesn't pick up well. Here is a link to the belt you need.Dyson DC1 ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Hi -- I have a Kirby Sentria and it is great except that I am getting no suction at all through the big silver power head. Suction through all the other attachments works well. I haev tried it with the roller belt on and off, and that doesn't seem to make a difference. Am I missing something?? Thanks!


You can take off the power head and look in that whole where the belt is and see if there is a paper towel or something in there clogging it up. Also tug on the belt and make sure it is tight - because if it is loose it is broken and you ... Kirby Vacuums

Our Bissell Cleanview II 3576M does a great job except that the filter cup below the dirt cup gets full very fast and the dirt cup barely has anything in it. To clean the whole house, I have to empty the dirt cup and clean the filter several times. It didn't use to work this way. It seems like something is missing, a gasket or seal maybe? I don't think dirt, hair and debris should be going straight to the lower cup and bypassing the upper. I looked at the user guide but can't see why it's happen


Contact Bissell Direct for a parts diagram and support at \015\012\015\012http://uk.bissell.com/EmailUs.aspx\015\012 ... Bissell 3576 CleanView II Bagless Upright Vacuum

New 50 pint frigidaire dehumidifier won't drain via attached hose , only collects water in bucket and this is a pain! How is the hose supposed to be connected? Seems strange to just screw it into the back of the unit; am I missing something?


... Vacuums

Dyson dc24 - just tried to use after being in storage, making loud noise and seems to be blowing out rather than in. Maybe a part missing? The hole at the top of the bin attachment is sucking air in.....should something be there to stop this?


The wand attachment at the top is supposed to only suck in when it\\'s in the upright position, otherwise the suction should be used when the vacuum in rolled on the carpet/wood/surface.If it\\'s still under warranty, contact Dyson directly. ... Vacuums

I have a kenmore upright 12 amp (M.N. 116.30003402C) vacuum that is not drawing anything up the hoes. There is no obstrution in the hoes and motor, belts, components are working, but there seems to be perhaps something missing(a part) or lost in the macinism that aids in drawing the air required to **** dust/dirt through the hoes and into the bag. Perhaps a diagram of parts and their function would help. Thank you.


... Kenmore 31912 Progressive Direct Drive Bagged Upright Vacuum

Hoover savvy handle release pedal does not retract. There does not seem to be any mechanism to force it back, is something broken or missing, like a spring?


Yes the handle release pedal is broken. i have the same problem and ordering the spare as i'm writing this email ... Vacuums

I just bought kaz model K76P (M) humidifier in Kyoto. I filled it to the right water level (a bit below) and plugged it in (nothing else is plugged in at that socket). The light comes on, but the water doesn't heat up. I can't read Japanese so can't read the instruction manual but it seems a simple procedure: fill with water, set the heating thing the water, plug in. Am I missing something or is the humidifier defect?


Take it back to the shop it should work and even though its in japanese ,they will know if your doing it wrong ,but i think it may have a damaged heater or a wire off where its been in transit ... Vacuums

I have a small canister type hoover vacuum and I would like to open it because the cord rewinder it jammed. I have removed all 4 screws but still can't seem to separate the two pieces. Am I missing something?


I may be able to help, but would need to know what model your machine is. Re-post, giving as much detail as possible and we'll see... ... Hoover S3330 / S3332 Straight Suction Telios Bagged Canister Vacuum

I have a Eureka 5902AVZ and the brushroll does not work. when i remove the belt, which is not torn nor worn out, the motor spins perfectly fine. Though when i put the brushroll back into place, it shows that the motor is trying to spin, but with resistance. it seems the brushroll will not spin if locked into place, because there is no attachment on the left side of the brushroll that will allow it to spin freely with the belt. am I missing some parts or is there something else wrong?


Hi and welcome to Fixya. I am Kelly. \015\012\015\012You have correctly identified the problem as the brush roll itself. \015\012\015\012There is a bearing under each end cap of the brush roll. You can gain access to the ... Eureka 5902AVZ Bagless Upright Vacuum

Panasonic mc-e4113 Upright vacuum. The belt that drives the brush in front is broken I have found a spare for this but there seems to be a pulley missing on the main drive shaft that the belt needs to fit on. I can't believe that there wouldn't be one? Can anyone tell me if this is the case and if so where I can get one from. Many thanks Sean


... Panasonic Vacuums

Replacing propeller Kirby G5: ordered a new propeller and can't seem to open up the unit to replace it. We've found all of the screws (we believe). Are we missing something?


This will help you out tremendously...\015\012\015\012http://reviews.ebay.com/KIRBY-VACUUM-RE ... Kirby G5 Bagged Upright Vacuum

Hoover Wind Tunnel 7500 Brush not Turning. I have replaced the Brush and the belt. The problem does not seem to be either to me. I believe might be a missing part. The place were the belt hooks on is a metal pole which never seems to grip the belt well. In fact it seems loose most of the time and slips on the brush, causing the belt to eventually burn up. Could there be a missing plastic or rubber piece meant to hold the belt taught  on the metal pole?


Check the Idler Pulley part Number 43241004 (Item 13 in the IPB)http://64.49.205.183/v/u6451900.pdf ... Vacuums

I have a Hoover, Steam spin scrub, Model F5897-900. Only used it a couple times and the motor gave out. First started being noisy then a bad smell. It did seem noisier that what I would expect from the start but I didn't realize it was a problem with the shaft of the motor. I took it apart and found the motor shaft wasn't true and causing sparks. The motor looks like it can not be taken apart and repaired. This seems like a default from the beginning but it is past warranty. Also noti


You will have to replace the motor and the hose asm. thehooverstore.com may be able to help, or you should be able to find a repair shop that can order them for you. ... Vacuums

I'm trying to pull the fan drive of my vacuum so I can get to the motor but Ican not seem to get it off. I was wondering if there is a release switch or something that is preventing me from doing this. Also the motor seems to be burning but I think it's because ther is something in there clogging it up.


Check to see if it has reverse threads, Most do ... Vacuums

My Kirby 2HD has started making an odd roaring noise but still works fine. I have taken the front assembly off and cleaned and adjusted the roller and checked the belt. The noise seems to come from the motor housing. I have tried to wiggle the main shaft at the front (bearings?) and it seems tight. Can't seem to get the other housings apart. Any ideas? Thanks, John


It is quite possible, it just needs lubed. The motor comes in direct contact with dirt so, you have to make sure the front bearing has a drop of oil on it from time to time. If it starts to scream at you within one month, after oiling, the bearing ... Kirby Heritage II Vacuum

My Miele capricorn has started making an odd noise. It seems like something is blocking the engine. I've turned if off and on, and reset it and it still have the odd, almost loud barking noise. The power nozzle also does not seem to be working. I've checked the connections. Right before this happened I was using the vacuum. I didn't notice anything out of the ordinary until this.


Greetings,\015\012\015\012This is a major problem. The Miele vacuums motor should never make a loud noise, period. The way the motor is designed, it's quiet and should be quiet for the life of the motor. There are two motors on your ... Vacuums

Kenmore 116.35922500 brush wont turn. Seems to come on if handle angle is held at just the right position but it is intermittent. Reset button is not popped up and doesn't seem to have any effect.


... Kenmore Vacuums

Cleaning solution does not come out of the rotating cleaning head or the hand-held nozzle the solution pump seems ok but does not run (electrical continuity check between the two leads on the pump show very low resistance so they seem to be intact) - no dirt or blockage is apparent (it is a very simple device with 1 moving part wires to the pump also pass a continuity check THERE IS NO VOLTAGE on the pump leads from the control circuit board when I turn on the "manual" cleaning mode - a


You can contact Bissell directly at the following\015\012\015\012For UK inquiries:\015\012Monday - Thursday 9 am — 5 pm\015\012Friday 9 am — 4 pm\015\012\015\012BISSELL Homecare (Overseas) Inc ... Bissell SpotBot Robotic Wet/Dry Vacuum

Have a Eureka Power Plus 12.0 Amps Model 4702 Type A 120 volts and 60 HZ that there is something wrong that it isn't picking up right and you can actually feel the air coming out of it near where the bagless canister attaches. My thoughts are that a seal is missing around where the hole lines up when the cannister is locked in. This Vac was my Mom's and she passed away and I think a part went missing maybe when it was taken apart to clean the filter and empty the canister. Need to figure out if


... Vacuums

The motor just went out on my 2 year old vacuum with light usage (hardwood floors in a very small house.) The Sears repairpeople are estimating ~ $130 to fix (this includes parts & labor). I'm wondering if it's worth investing $130 into something i've spent $350 on only 2 years ago. Shouldn't these machines last longer ? Is there something I could do to get them repair free as it seems the motor must have been faulty to only have lasted 2 years. Thoughts ?


Aye, get a dyson, if its out of warranty there's not much u can do bout it :( ... Kenmore 25512/ 25513 Progressive Canister Vacuum

Model#F5858-910 hoover steam vac,silver ,spin and scrub. It doesnt seem to spray cleaner it seems to stream it now. what could be wrong? I cant get to end of where it sprays to see if something is blocking it . otherwise it works great. I have it about 8 yrs. always worked good until recently


... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0356 seconds