Having problems with your Riccar 8650/8625 s Vacuum ?
The motor on my riccar 8650 is very loud. is there brushes that can be replaced?
Your. 8650 is likely well over 20 years old. It has carbon brushes in the motor that may need replaced but your best bet Is to take it to your Riccar dealer to diagnose it or you might replace the wrong thing. You have a very durable long lasting machine obviously but there are minor things that need occasional service to keep it running properly for many more years. This series started with the 8600 models of which I still have many brought in for annual service. There has been an 8700 and 8800 series and now the latest 8900 series which has been out well over 10 years.
Repair Help & Product Troubleshooting for Riccar 8650/8625 s Vacuum
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
The motor on my riccar 8650 is very loud. is there brushes that can be replaced?
Your. 8650 is likely well over 20 years old. It has carbon brushes in the motor that may need replaced but your best bet Is to take it to your Riccar dealer to diagnose it or you might replace the wrong thing. You have a very durable long lasting ma ... Riccar 8650/8625 s Vacuum
Noise My Dyson DC08 is making a loud, rough, vibration/noise that seems to be coming from the from the rotating brush housing. I replaced the old belt which was several years old and slipping. When I run the motor with the new belt removed the machine sounds normal. The bearings on the rotating brush seem to be running smoothly when turned by hand both when out of the brush holder and when installed in the machine. I can't find anything rubbing on the belt or rotating brush. I applied a bit o
Hi there, it's Jack at Dyson.\012I'm sorry to hear you're having difficulty with your Dyson vacuum. From your \012description, it sounds like the model number you've supplied may not be correct, \012as DC08 is a cylinder vacuum which doesn't use ... Dyson DC08 Cylinder Bagless Canister Cyclonic Vacuum
I have recently replaced the belt and filters. The belt is in the correct position and the rotating brush moves freely. The motor is very loud. It still vacumns but I'm afraid the motor will burn up.
Does it sound different than it did before you made the repairs to it or does it sound the same. Just so you know some of the upright vacuums on the market today sound like a jet airplane landing in your living room.Ca ... Bissell 6594 PowerForce Bagless Upright Vacuum
I have a Filter Queen Majestic 360 and am having problems with the powerhead. There is a loud rattling noise in the powerhead, especially when I vacuum thicker carpet. I have replaced the motor, roller brush, and belt, but the rattling remains. It sounds like it is coming from the roller brush area,and when I turn the powerhead over, it rolls free and sounds fine. Any thoughts?
Hi there, as per your information i guess its a problem of power transformer. He can't supply the proper power in the motor & thats why the noise will come from the transformer. Thanks & waiting for your feedback. ... Filter Queen Majestic Canister Vacuum
Replacing a belt on the Riccar 8850...I see how the brush assembly will work with the new belt. But I don't see how a new belt will turn on the small rod extending from the motor. Is there a pully missing?
There is not a pulley missing, when the belt is tight the shaft will turn the belt but when the belt loses elasticity it will slip on the shaft when being used on the carpet. Replace the n\012belt at least once or twice per year. ... Riccar 8850 Vacuum
I have had my Bissell Healthy Home for just over a year. I use it once or twice a week on five area rugs and two small bedrooms with wall to wall carpet. Just recently, the motor started to sound extremely loud and it smells like it's burning. The vacuum still picks up everything and all the brushes are turning. Advice? I really like this vacuum and would really like to fix it rather than replace it!
Hi,Here is a tip that I wrote about my Bissel but I bet you have the same problem and the hose is clogged...Bissell Bagless Upright Vacuum no ... Bissell 5770 Healthy Home Bagless Upright Cyclonic Vacuum
Bissell cleanview helix makes loud noise when the roller is engaged. The motor runs quiet when the belt is disconnected. Do i need a new brush roller? I already replace the belt
... Bissell 21K3 CleanView Helix Bagless Upright Vacuum
How to replace the motor brushes? When should the motor brushes be replaced? Where can I purchase motor brushes for Model 1500 Easy-flow?
... Easy Flo EF1500 Vacuum
Bissell Powerwash Proheat. model 1698-j, 220-240v, 50/60Hz, 1200-1400w. Motor stopped suddenly (ident label specifies type Ametek 119464-02), supply inline fuse at motor ruptured, fuse replaced but motor sparks like an angle grinder at armature and blew replacement fuse. Where can I obtain a replacement carbon brush set for the motor. UK based
... Bissell Vacuums
Brush motor does not turn. Vacuum motor works. How to replace brush motor?
... Eureka 431A Optima Bagless Upright Vacuum
My bissell model 18Z6 has developed a loud noise and vibration when the brush is running. I have removed the brush assy and cleaned all the hair, etc but still the noise. I ran the brush motor with the belt disconnected and all seemed ok, but of course there was no load on the motor. I suspect a problem with the brush assy bearings or axle or both but I hate to just throw parts at the problem. any suggestions would be greatly appreciated.
... Bissell Vacuums
Bissell 6595 problems with roller brush. I've had this happen with two of the same model. Each one didn't last more than seven months! First, it became loud when vacuuming, then there was a burning smell. When you try to replace the belt, you see that won't do any good because the fitted end of the brush is melted. The housing part the roller brush fits into is melted too. There's no place for the roller brush to fit into. I tried to upload pics, because I don't see how replacing the roller brus
... Bissell 6595 Lift Off Bagless Upright Vacuum
No power when turned on, I checked motor brushes and they are almost worn out, could this be the problem? and where do I find replacement brushes? I have checked on Dirtdevil's site but I don't see any motor brushes. I am in Montreal, Canada. Thank You.
Hi,\015\012Before that I wouild check the switch...the switches on those things go bad regularly...get a meter and check the power on either side of the main switch and I think your problem will be there...\015\012\015\012heatman101 ... Dirt Devil 12 Amp HEPA Filter Vacuum Vacuum
Brushes in motor are arcing badly and motor only occasionally will start. How do i remove the motor brushes for replacement. (from the green plastic case)
This is kinda of tricky. need to know what kinda of vacuum it is first. However if you get it apart. To fix this problem the armeture brass needs to be cleaned & you should replace both carbon brushes. Should be cheap to fix if you are up to it. ... Vacuums
Replace Vaccum Motor Brushes
... Kenmore 23812 Progressive PowerMate Bagged Canister Vacuum
I have a Kenmore canister model 116.25812 that makes a very loud beating noise when the powermate is turned on. I replaced the belt, but still has the sound. Also replaced the bag and both filters. Suction is great, but is very loud when the brushes turn.
Carbon brushes on ME-48 power head motor worn out. Where can I get replacement brushes? Motor is O 90197X7, Lamb, Model 118173-73 - 240V 50/60Hz
Hi Les,Most sites sell only the motor.Here's a website that includes motor brushes: http://www.kleen-ritecorp.com/search.aspx?IsSubmit=true&searchTerm=lamb+motor&gclid=CIbZ59zwiKgCFQprKgod8W2itQHope you can find the righ ... Filter Queen Vacuums
Kirby Vacuum Hi Bruce, In my opinion, yes the Kirby would be worth it, as long as you are not replacing the motor. The switch would be the most expensive part besides the motor that would need to be replaced. The switch costs USD 49.99, the cord is roughly $39.99, and the carbon brushes are $29.99. I can easily walk you through any of these repairs should you need help. Kirby's are great vacuum cleaners, that usually last 30+ years. Brand new these machines sell in the US for $1600 or more,
You can get better prices from Goodvac.com ... Kirby Generation 3 Bagged Upright Vacuum
Do i need to do anything special when replacing the brushes in a lamb ametek 117500 motor? It looks like I can just remove the old brushes and insert the new ones. Is it this simple? Will the motor work again? Thanks
Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=758676\015\012Generic problem for all Vacuums\015\012Do I need to do\015\012Posted by edkraynak on Jul ... Vacuums
I replaced the belt on my Dirt Devil Featherlite Bagless Vacuum and the brush roller rubs and makes a very loud noise when turned on. I have gone exactly by the manual instructions and made sure the belt and end caps were on correctly, but the bristles still rub the back and it makes a very loud noise. Without the brush roller in the vacuum, it sounds and runs normal. What could the problem be?
Http://www.geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=561283\015\012Generic problem for all Vacuums\015\012I replaced the belt on\015\012Posted by piggyt ... Vacuums
What causes these things to become unbearably loud? We've cleaned evey filter on the machine, pulled every speck of hair and lint off the brushes, changed the belt, no clogs anywhere. I've totally (and I mean totally, down to the brushes on the motor!) torn this thing down and put it back together with no difference. Also have a Eureka bagless, and after minimal use, and almost anal retentive maintance, it does the same thing,to stinkin loud. Wish one would **** up the other to save a trip to th
A clog in the hose or dirt inlet by the brush roll will cause the motor to sound loud. But so will a bad motor bearing, or motor fan, in which case you would have to replace the motor. ... Bissell Vacuums
I have a hayward 1HP superpump with an Ao Smith UST 1102 motor on it. Last year I had a leak in the pump, and I believe I got some water in the bearings of the motor. Over the winter I replaced all the seals in the pump, and have no leaks this year, but the pump is sounding pretty loud since opening the pool this year. I have (2) fold question: (1)I can not find any information on the where I can find a replacement bearing for this pump. (2) I can not find a procedure on HOW to go about
Hello. I get my parts here http://www.poolcenter.com/parts_pumps_hayward_superpump.htm\015\012\015\012Joe ... Vacuums
The brushes will not rotate on my hoover vacuum. the belts are in good shape, the motor is turning the vacuum motor, but the belt on the brushes seems loose. I ordered a replacement belt but still nothing. Their is a small "idler" but their dosent seem to be enough tension on the belt. Any ideas?
Did you order the correct size of belt? These are the belts you should have:Hoover Windtunnel Belts ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum
Why would my dyson dc 17 brush motor be extremely loud, but sound normal when brush is not spinning?
Could be the bearings on the end of brushbar need replacing,or it may be the clutch needs setting , lower the handle down to the floor then up again do this about three time to reset clutch.... ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum
I have the bissell power force bagged upright vacuum and the brush is not turning, I have replaced the belt but the brush will not move but the metal piece that is hooked to the motor that spins the belt and brush is turning but the brush won't, and the belt starts to burn
Sounds like your brush roll is seized. Remove the brush roll (see picture) and make both of the end caps spin freely. If not, replace it and you should be set. *An example of a brush roll* ... Bissell 3522 PowerForce Bagged Upright Vacuum