Having problems with your Riccar 8650/8625 s Vacuum ?

Riccar 8750 I have a 8750 riccar vacuum and it suddenly didnt want to start. someone told me it has a reset button but I dont know where I could locate it. can you please help?

Answers :

I have an 8625 and the button is now white not red. Probably fadded. Thanks that was the reset button and it solved my problem.
There's a small red button about one inch to the right of the left wheel.
Repair Help & Product Troubleshooting for Riccar 8650/8625 s Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Riccar 8750 I have a 8750 riccar vacuum and it suddenly didnt want to start. someone told me it has a reset button but I dont know where I could locate it. can you please help?

I have an 8625 and the button is now white not red. Probably fadded. Thanks that was the reset button and it solved my problem. ... Riccar 8650/8625 s Vacuum

My daughters X-Treme Scooters | X-360 - 350 Watt Electric Scooter - Pink the fuse keeps breaking or blowing in it. Do you know what could be causeing that? Please help she really loves her scooter and we dont have a clue nor a manual to see what is wrong with it. It will run until she pushes the gas all the way and it gets hot.

Hi, be sure you are using the right amperage fuse in it. Check any exposed wires on it they may have got skinned up, causing a short and blowing this fuse. You say it gets hot when she gives it full power, so its blowing when its drawing the most amp ... Vacuums

Sponge filter I have a kirby sponge filter for my Sentria shampoo system and dont know where it goes. It stop working and making foam. Kirby sent me the sponge filter saying this is what i need and i would know where it goes. I dont nor kind I figure it out. please help!!!!!!!

On the end of the shampoo tank where it attaches to back of motor where the bag is normally attached ... Vacuums

I have the brother Ls-2000 sewing machine i threaded the top as well as the bobbin but when i try to sew the thread gets stuck and it bunches up and tangles in the bobbin. also the little bit that did sew was tight stitches on one side of the fabric but very loose on the other side I followed the instruction and it keeps happening i need help i dont know how to fix it please help me

Adjust your tension.You probably did not wind your bobbin properly as well.Make sure you oil your machine every month or so and make sure your bobbin is seated properly before you sew.\012\012Go slower with the pressure foot speed and use the r ... Vacuums

Im try to shampoo my carpets with my thermax. i lost the manual and dont know how to set it up for shampooing. can u please help?

Just for begining here is the manual. Choose your model and download:AF1 Owner’s Manual ... Thermax Vacuums

I knew my pin but then I have another atm card with a different pin so now i dont know both of the pins can you help me please

The only people that can help you with a problem like this is you banking institution. Go and see them. ... Vacuums

Dyson dc07 The rotating brush on the bottom of my vacuum was filled with strings. I removed the brush by undoing all yellow plastic screws from plate. Removed all strings and replaced as best I could and it was hard to get the brush back in and the belt around it. I dont have my manual but it fits so it should be correct....? Right? No, not true, because when I turn it on and try to and vacuum (by lower canister with foot release) it makes that terrible ratching sound). Please help

The loud ratching is a warning to tell you that there is something stopping the roller bar from rotating this is a very common thing lay the machine on the floor front side down take off the bottom plate and just check the belt is in the centre of th ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Need to vacuum and my Kirby G4 and was wondering if it has a power reset button, or if anyone knows what it could be. It is in very good condition and was rebuilt 2 yrs ago. Please help???

Hello, sheriI was trying to help you out here. Maybe this will help some? I was going backto some customers that asked questions in the recent past and even fartherback. It appeared that no one answeredsome of them, So, I thought I would t ... Kirby G4 Bagged Upright Vacuum

I recently ( approx. 2-3 months ago ) purchased a dirt devil. Now it is not picking up properly. When I push vacuum forward it picks dirt up a little bit, when I pull it back all the dirt falls out of the bottom. I replaced the filter today and it has not solved my problem. I dont know where my warranty is. Can you please help me?

Hi sounds like your line is stopped up somewhere , check ur suction an make sure your brushes are spinning, if they are try a wire clothes hanger to the hose at the bottom hose to dislodge anything that mite be stuck ... Dirt Devil Vacuums

RE-620TC. I hve this microwave from my friend but I dont know who to operate it, will you please help me send this information .

... Vacuums

Hello, Could you send me an exploded view of an engine kirby please? My Kirby vacuum cleaner I think for 1997 I think it is garnet, having wanted to change the coals, I do not know the back, is the cause of my request, I contacted a person previously in Bastogne (Belgium) several times which promised to help me but in vain, I count on your good will so I can reassemble it and use it again. In advance, thank you

Try this site out:www.onlinevacshop.com/kirby-G5-parts-manual.phpGood Luck!Jim ... Kirby G5 Bagged Upright Vacuum

Hello, could you help please. I have a Bissel ProHeat 9400-M. The water remains in the bladder when the machine is on, in other words nothing happens and I cannot clean with it. Inside the tank the small flap is in the open position. I have always used your products although I did run the Bissell over an area that had been cleaned with another product. Could that have caused the problem by blocking it somewhere? I have cleaned everything and cannot see a blockage. Thank you for your help.

... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

I have a kenmore vacuum cleaner model # 116.23612. When the hose is attached to the canister it runs, but if you remove the head to just use the hose the unit stops working. Is the motor dead or is there some type of reset or fuse. Could you please tell me how to test this. If so could you please send me instructions on how to replace the motor. Thank you in advance for your help, Tony

... Kenmore Vacuums

You might not believe this but i don't know how to turn it on. I thought it was on the power nozzel but It is just got an orange light on. I know this sounds silly but please help me.

The on/off switch is located on the hose handle. The "O" is for off, "I" is vacuum only, and "II" is for vacuum and power nozzle. The light below the switch indicates there is power to the vacuum.\015\012If your vacuum doesn't run, there are ... Electrolux Guardian Bagged Canister Vacuum

I have a fake nokia n8 cell phone(basically called chinese). i didnt know about flight mode and turned it on by mistake. now i dont know how to turn it off. menu is not opening and i cant make a cal... plz help me out.. :(

Take the power button should give you the option to turn off airplane mode ... Vacuums

Hi, I have a Casio fx-115s scientific calculator which I've had for around 25 years. I am unable to use the bracket function and have lost the instructions. Could you please give any advice to save me having to buy a new calculator? I'm not sure how to use the brackets, whenever I press the ( ) buttons, it shows -E- on the screen which I'm presuming is an error message. Please help.

You should be able to use parentheses in the same order in which you would write the arithmetic expression. For example, 4*(3.5-1.5)= should give you 8. Without the parentheses, this would 12.5.Essentially, the left parenthesis comes imme ... Vacuums

GE 2-Motor Canister Vacuum, 106766 Please help has anyone had this vacuum catch fire? I lost everything and my pets. I need anyone else to please let me know if you have had fire caused by this vacuum. Contact me at [email protected]

... GE 106766 Bagged Canister Vacuum

Help ok the diagram is helpful but i have a black wire that came loose from somewhere it has a little prong on it does it click back in opposite from the white let me know please

I am not sure what exactly you are referring to but I think that it may be a motor lead. See pictures below (shown is white but second wire to the motor is black) ... Rainbow E series Canister Wet/Dry Vacuum

Hello experts. I have a Hoover u6454-900 vacuum and need new belts a thin one and a thicker one. and I do not have the manual and do not know the parts numbers for these. please please help.

... Hoover U6454-900 WindTunnel Bagged Upright Vacuum

I have a Eureka Altima vacuum. The model number is 2996. I don't think my vacumm is sucking any dust. Plus, it smells like a burning leather. What should I do? I have tried to get help from others and they tell me that I should change the belt. But, I don't know where it is. Please help.

Sounds like the belt for sure. Here is a link with the owners manual. It shows how to get to and change the belt. http://www.eureka.com/index.php?option=com_productdisplay&view=productdisplay&task=getproducts&productid=2&produ ... Eureka Altima Upright Vacuum Model 2996AVS Vacuum

I can't open it to clean it, please help! I know I have to pull the grey cover, and I have tried hard but no luck. Seems attached from the bottom, so I am not sure how it will come out. Thank you for your help.

I had the same problem. It normally opens with a little tug on the door but if you are like me and you let it fill up with a year's worth of pet hair etc., the door will jam. The only option is to ... SweepEZE 600 C-1 Canister Vacuum

The little toothed belt on my bissell shampooer broke got a replacement but don't know how to put it back on Stark's where I bought the belt wouldn't help me man said he isn't a mechanic. well neither am I so could you send me a diagram I could follow? Thanks

Hi!  Your question has come up under Bissell ProHeat, although you don't actually specify that model. Assuming it is, the belt change operation is quite simple but hard to describe in words (it will sound much more complicated than it actually i ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

Low suction Have a Powr-Flite PF 18, suction is good at motor, but low at where hose comes out of top of vacuum. Could new lid seals help the problem? Where can I get new seals for this model. Also my zip is 98801 and my shop is not listed, could you add it please? Sew Creative 1139 N. Princeton Wenatchee, Wa 98801 509-663-5516 Thanks, Lauren-Sew Creative

Replacing the motor cover solved the problem, it must have been warped and was letting suction out thru it. ... Vacuums

My Dyson vacuum works fine for cleaning the rug but the hose doesnt get any suction at all. I removed the hose and all the parts around it that I could and dont see any clogs or broken pieces. I lost my manual so I dont know if this is addressed, or if there is a switch Im not flipping. Gave it a thorough look but found nothing.

Hi there,Sorry to hear you're having a problem with your DC07. If you have suction through the cleaner head but not through the wand, it sounds as though you have a blockage. Although you say you've already checked for these, you may find ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Hello, I have a Riccar 8000. The belt works, the bar spins, and it will **** things up. However, it will not pick up threads and dog hair or anything from the carpeting. Mu husband took the bottom off and there were a couple of small parts on the plate. We have no idea where they belong. Could not see them in the photos in the manual. Could it possibly need a new roller? Any help would be most welcome. Thank you! Mary Simon

... Riccar Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0634 seconds