Having problems with your Riccar 8955 Upright Vacuum ?

8955 Upright Vacuum: How to change belt?...

\015 How to change belt?\015

Answers :

Be sure to unplug your vacuum from the electrical outlet before proceeding!
\015\012
\015\012-Turn your vacuum upside down so that the handle is resting on the floor and nozzle portion is resting on a work bench.
\015\012-Remove the 2 phillips screws from the metal bottom plate and set the bottom plate aside.
\015\012-Look at the right side of the brush roll. You will see a bent metal rod that attaches to the brush roll end cap. This is the clutch rod that allows your brush roll to spin or not depending on the position of the carpet/floor switch on the top of the nozzle. Pull this rod out of the brush roll clutch only. Leave the switch end of the rod where it is and just let the rod rest there.
\015\012-Pull the brush roll and old belt out and dispose of the old belt.
\015\012 To install a new belt; put the new belt on the motor shaft first, next put the other end of the belt over the end of the brush roll and stretch belt and brush roll back in to place. Notice that on the brush roll end cap opposite of where the clutch rod goes, there is a metal piece with a slot cut into it. Be sure that this slot mates with the plastic stop in the nozzle so that the end cap cannot move.
\015\012 Snap the clutch rod back in place and rotate the brush roll by hand to make sure the belt is not pinched.
\015\012 Replace the bottom plate.
Repair Help & Product Troubleshooting for Riccar 8955 Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Vacuum belt keeps coming off. Need instructions on how to change belt on Panasonic mc-6955 upright vacuum cleaner.


... Vacuums

How do i change my Kenmore upright vacuum belt?


... Kenmore 33721 Upright Vacuum

How to change belt on old upright Hoover vacuum


... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

How to change belt on eureka vacuum 2996 - Eureka Altima Upright Vacuum Model 2996AVS Vacuum


The information you're looking for can be found on page 8 of the manual via this link: http://www.eureka.com/service/manuals/80244.pdf ... Eureka Altima Upright Vacuum Model 2996AVS Vacuum

How to change belt in eureka altima vacuum - Eureka Altima Upright Vacuum Model 2996AVS Vacuum


Here is the belt you need to replace and the manual which has instructions:Eureka Altima Belts ... Eureka Altima Upright Vacuum Model 2996AVS Vacuum

Changing the belt for #u4264-930 upright vacuum


... Hoover Vacuums

Upright vacuum cleaner model dm4485 belt change assistance


... Hoover Vacuums

Change belt on eurika optima vacuum - Eureka 431A Optima Bagless Upright Vacuum


This link is for the manual will give you instructionshttp://www.eureka.com/FileLibrary/d944cbc8479a49aeafd4f964eb4842df/77297.pdf ... Eureka 431A Optima Bagless Upright Vacuum

How to change a belt on eureka vacuum 4903 f - Eureka Power Plus 4703D Bagless Upright Vacuum


... Eureka Power Plus 4703D Bagless Upright Vacuum

How do you change the belt? - Eureka Altima Upright Vacuum Model 2996AVS Vacuum


First you will have to remove the top cover where the brush roller is. I cannot remember off the top of my head, but I believe that there are 2 possibly 3 screws on the top cover. As you look at the machine from the front, they should be just behind ... Eureka Altima Upright Vacuum Model 2996AVS Vacuum

How to change belt on hoover savvy vacuum - Hoover U8145-900 Savvy Bagless Upright Cyclonic Vacuum


How do I change the smaller brush belt on a Hoover Windtunnel Cyclonic? ... Hoover U8145-900 Savvy Bagless Upright Cyclonic Vacuum

Change belt hoover upright vacuum - Hoover Vacuums


Take out the screws on bottom where the brush is pull out brush assembly and look for a broken belt ... Hoover Vacuums

I HAVE A EUREKA ALTIMA AND CANT CHANGE BELT - Eureka Altima Upright Vacuum Model 2996AVS Vacuum


The hood will come off if you loosen two screws at the front on top of the hood by the brush bar bit that is slightly raised. Then there's a screw to the left hand side of the upright either below the hose or duster area. Once all screws are undone, ... Eureka Altima Upright Vacuum Model 2996AVS Vacuum

Eureka altima model 2993 how to change belt - Eureka Altima Upright Vacuum Model 2996AVS Vacuum


... Eureka Altima Upright Vacuum Model 2996AVS Vacuum

Change belt - Bissell Upright Vacuum - The Pet Hair Eraser 1 ea Vacuum


... Bissell Upright Vacuum - The Pet Hair Eraser 1 ea Vacuum

My question earlier today referred to a Kenmore Progressive upright vacuum. Your answer suggested that I change a belt, if the reset button did not work. Does a direct drive really have a belt? Regards, Jim Buckley


Direct drive does not have a belt. It is a shaft with gears. What is wrong with your vaccum? Maby i can help. ... Kenmore Progressive Bagless Upright with Inteli-Clean SystemVacuum

I have an old upright hoover vacuum. I need to change the belt but can't figure out how to get to it. The bottom plate over the roller brush comes off but I can't get anything else off to get to the other end of the belt.


Model no. req ... Hoover Vacuums

How to change belt on Bissell 6582 vacuum - Bissell 6594 PowerForce Bagless Upright Vacuum


Here is a link to the belts you need and to a manual you can view with instructions.Bissell PowerForce Belts and ManualHope it helps ... Bissell 6594 PowerForce Bagless Upright Vacuum

How do I change the belt on a vacuum cleaner - Shark Helmet NV22L Shark Navigator Upright Bagless Vacuum


You don't. Call cust. service, they sound send a new head. ... Shark Helmet NV22L Shark Navigator Upright Bagless Vacuum

How do you change a upright panasonic vacuum belt?


... Panasonic MC-V5454 Upright Vacuum

How to change the belt on hoover upright U3305-030 vacuum


... Hoover Vacuums

Change belt nv22l sharp upright vacuum


... Sharp Vacuums

8955 Upright Vacuum: How to change belt?...


Be sure to unplug your vacuum from the electrical outlet before proceeding!\015\012\015\012-Turn your vacuum upside down so that the handle is resting on the floor and nozzle portion is resting on a work bench.\015\012-Remove the 2 ... Riccar 8955 Upright Vacuum

Change belt on hoover savvy bag and bagless upright vacuum


... Hoover U8155-900 Savvy Bagged Upright Vacuum

Change belt on a Sterilaire Vacuum upright


A very easy procedure!Look at the front hood of the Purepower (where all the lettering is including the 1600 or whatever the model number and name is located at) and you'll see at the back two screws either side where the back wheels are. Unscrew ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0776 seconds