Having problems with your Riccar 8955 Upright Vacuum ?

Where is the belt located? - Riccar 8955 Upright Vacuum


Answers :

The "belt" is normally the drive device that turns the beater brush found on the bottom front of the vacuum. Its purpose is to beat the rug and cause dirt and debris to rise up from the carpeting and be sucked into the vacuum.\015\012If the belt is missing, you may not see it. If the belt is in place, it will loop around the beater brush and back to a drive motor.\015\012Since belts can break on a regular basis any covers over it should be easy to remove via small slide levers or at most by removing a few screws from the bottom of the vacuum. The new belt must be attached properly in order for the brush to move in the correct direction.\015\012If you are going to replace the belt it is probably a good time to clean the beater brush and lubricate the end pieces of the brush with some WD40 as well.
Repair Help & Product Troubleshooting for Riccar 8955 Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Where is the belt located? - Riccar 8955 Upright Vacuum


The "belt" is normally the drive device that turns the beater brush found on the bottom front of the vacuum. Its purpose is to beat the rug and cause dirt and debris to rise up from the carpeting and be sucked into the vacuum.\015\012If the belt is ... Riccar 8955 Upright Vacuum

Riccar 2150 belt replacement - Riccar 8955 Upright Vacuum


... Riccar 8955 Upright Vacuum

I dont know where my Vacuum belt is located? - Eureka 4700A Maxima Bagless Upright Vacuum


The link below is the manual it will give you step by step instructions on page 19 how to replace belt and brushbar ..http://dl.owneriq.net/b/b7517422-db37- ... Eureka 4700A Maxima Bagless Upright Vacuum

How to change belt on riccar VIBCL - Riccar 8955 Upright Vacuum


... Riccar 8955 Upright Vacuum

Replace belt on riccar radiance - Riccar 8955 Upright Vacuum


... Riccar 8955 Upright Vacuum

How to replace belt on Riccar - Riccar 8955 Upright Vacuum


Greetings from GoVacuum,\015\012\015\012I will attempt to walk you through the belt change on your Riccar 8955 upright vacuum cleaner. I have taken pictures for you for each step to ensure that it's done properly. What you'll need to ... Riccar 8955 Upright Vacuum

Riccar 8955 upright vacuum belt and rod connecting slider switch won't stay engaged


... Riccar 8955 Upright Vacuum

I have a Eureka Contour model 2900 type A upright vacuum, the roller works fine nothing clogged, took it apart motor blade is free of debris, no suction from tube and blasts OUT air from the front HEPA filter location. New bag, New belt, nothing in hose.any clues as to why this can be happenning? Air should not be blasting out of the HEPA filter.


Even with your explanation,it seems the hose is clogged.Try taking the hose off,then blow through it or pour water through it.If this doesn't do it,make sure the suction canals are going to the proper areas. ... Eureka 2900A / 2901A Contour Bagged Upright Vacuum

Replace belt? - Riccar 8955 Upright Vacuum


... Riccar 8955 Upright Vacuum

How to replace the belt in the 8850 model - Riccar 8955 Upright Vacuum


Greetings from GoVacuum,\015\012\015\012I will attempt to walk you through the belt change on your Riccar 8955 upright vacuum cleaner. I have taken pictures for you for each step to ensure that it's done properly. What you'll need to ... Riccar 8955 Upright Vacuum

Where is the belt located - Eureka 3276AZ Pet Lover Bagless Upright Vacuum


... Eureka 3276AZ Pet Lover Bagless Upright Vacuum

Remove and replace belt - Riccar 8955 Upright Vacuum


Hi There,\015\012\015\012Here's a very helpful repair that I did exactly for your problem on how to replace the belt on your Riccar. Your model, the 8955 is more difficult then other models due to the rug/floor selector knob. No worr ... Riccar 8955 Upright Vacuum

How to check the location of the pump belt? - Bissell 1699 ProHeat Clear View Upright Steam Vacuum


Take off belt cover on the left side of the top cover, turn cleaner over, take out screw from red lock and remove, pull cap and brush roll out, unhook the cogged belt, then you can replace the pump belt thru that opening. Put belt over the pump pull ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

I have model a Riccar 8905 upright vacuum cleaner. When changing the belt a part fell out and I don't know where to put it or what it does.


... Riccar Vacuums

How does the belt go back on? - Riccar 8955 Upright Vacuum


... Riccar 8955 Upright Vacuum

Broke need replacement belt - Riccar 8955 Upright Vacuum


You can get replacement belts for that model here:Riccar 8955 Replacement Belts ... Riccar 8955 Upright Vacuum

The original belt on my upright Kenmore Progressive broke and I replaced it with the spare that was in the vacuum. The vacuum and spare belt are about 10 years old. Then the spare broke after one vacuuming session and there was a burning smell coming from the vacuum. I ordered new belts and replaced it with the new belt. It seems to be working fine with no smell. I checked the belt after I vacuumed the family room and although it was in tact, the belt was very hot. Is that normal? Should t


The belt heats up due to the friction, as well as being in contact with the shaft of a hot motor. It is normal. ... Kenmore Progressive 35922 Bagged Upright Vacuum

I have a Eureka 4800 series the Boss upright with a bag and Hepa filter. I love it! I was just vacuuming with the hose part and all was well and then suddenly the lower brush came on and a "burning" smell followed. Thought it was the belt so my husband was going to put on the new belt which I had on hand! When he turned it over, the "bar" that holds the belt looks as though it "shot through" the plastic side of the housing on the vacuum. There is melted plastic on the outside of the vacuum and o


I had the same problem. Take out the old belt if possible. Remove the 4 screws inside the filter and the 3 on the front of that housing. pull out the foam around the motor. carefully pull out the suction tube that is press fit against the motor. ... Eureka 4874 Bagged Upright Vacuum

Bissell Power Track Cyclonic Upright Bagless Vacuum.. ..The spin brush works laying down....when upright it won't spin! I cleaned any and all hair from the roller....belt is not broken....but do I need a new belt though? The vac is a few years old bever replaced the belt yet.


You need a new belt. ... Vacuums

Vacuum belt keeps coming off. Need instructions on how to change belt on Panasonic mc-6955 upright vacuum cleaner.


... Vacuums

Is there a diagram/picture to help me visualize how to put cleaner belt back in vacuum? I was taking base of vacuum apart so I could get rid of hair that were wrapped on the roller. The cleaner belt came to loose and I could not figure how to fix it back. the model is eureka upright bagless series 430


Hi,Sorry to hear your belt fell out. Not good if you've never replaced a belt before...Here is a website where you can read a detailed description of how to change a belt: http://www.ehow.com/how_8034505_eureka-belt-replacemen ... Eureka 431A Optima Bagless Upright Vacuum

Beater Bar Belt Removal from Upright Electrolux Vacuum


Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=783793\015\012Generic problem for all Vacuums\015\012Beater bar Belt Removal from Upright Electrolux...\015\012 ... Vacuums

Lever & belt placement in Kenmore Progressive upright vacuum


You are correct. The belt is supposed to go around the peg that is connected to the lever so that when it is on the Floor /Tools setting the belt is not driven by the drive shaft. ... Kenmore Vacuums

I have an electrolux genesis upright vacuum that I bought used about 8 years ago. It has been A great vacuum the best I ever had. I thought the belt had come off so I took it in for repair. They called today and said that the brush rotor motor was bad and it would be around 148.00 dollars to repair. My question is could I buy the part and have my husband replace it or would it be too complicated. Can you still buy an electrolux vacuum comparable to this one and how much are they. I love this vac


... Vacuums

I have the bissell power force bagged upright vacuum and the brush is not turning, I have replaced the belt but the brush will not move but the metal piece that is hooked to the motor that spins the belt and brush is turning but the brush won't, and the belt starts to burn


Sounds like your brush roll is seized. Remove the brush roll (see picture) and make both of the end caps spin freely. If not, replace it and you should be set. *An example of a brush roll* ... Bissell 3522 PowerForce Bagged Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0878 seconds