Having problems with your Riccar 8955 Upright Vacuum ?

How to install a the roller belt on a Riccar Rad.10?

Answers :

Repair Help & Product Troubleshooting for Riccar 8955 Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

How to install a the roller belt on a Riccar Rad.10?

... Riccar 8955 Upright Vacuum

My 4870 K Boss is 2 years old. I have replaced belts & filters in the specified intervals. This last time I replaced the belt after a year, it shredded 3 of them on the outside edge of the belt in about 5 minutes of use. I ordered a new brush roller & heavy duty belt which I installed. It began shredding the belt in less than 5 minutes of use. What is your suggestion? Is this a known problem with this model? Eureka says no and is not standing behind it.

The only reason why it would be shredding the belt is if the pulleys were not lined up correctly. Check the allignement of the belt to make sure there is nothing kepping the pulleys from being in line. The other thing that it could be is if the rolle ... Vacuums

Riccar model rad.7 upright (radiance). roller brush won't turn and red roller brush indicator is on. roller will turn easily by hand and belt is in place. how do i fix this?

As you already know, the red brush indicator light indicates that the brush roll has stopped turning, usually because an object has become stuck in the brush roll. When that happens you should turn the machine off (unplug it also for safety), remove ... Riccar 8955 Upright Vacuum

Beater Bar The "Beater Bar" or roller with brushes on it, is not spinning, therefore not picking up. I cannot locate my manual and need to know if it is belt driven and how to get at the belt to identify the size and purchase and install a new belt. Thank you for any assistance. [email protected]

Take off the bottom plate, then you can get to the brush roll and belt, on the model number plate, the number of the belt is on that, it is also on the belt if you can still make it out. ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Roller Brush How do I install the roller brush. I didn't pay attention when I removed it and now when I attempt to vacuum my low carpet it doesn't seem to be working. The green light on the head of the vacuum goes out when I click it down to the floor. It didn't used to do that. Plus I think I smell something burning. Could the belt be broken?

Try a new belt. The ends of the brushroller are different sizes, so you can't put it in backwards. There are numbers and notches on the ends of the brushroll. These notches/numbers need to match on both sides when installing it. (probably need b ... Kirby Ultimate G Bagged Upright Vacuum

I have a eureka bravo upright model 9600. I have removed the hood . I need to remove the brushe roller to install a new belt. I cannot figure out how to remove the brush roller.

Check out this URL:\015\012\015\012http://www.svcvacuum.com/beltrep2.html\015\012\015\012looks like it has just what you are looking for.\015\012Would appreciate a thumbs up on this if you find it beneficial.\015\012Paul ... Eureka Vacuums

My Riccar 8850 belt works but the roller will not spin

I see this same problem posted repeatedly here. The only solutions offered are to "change the belt". When most people state that they've changed the belt and still have the same problem the recommendation is usually "are you sure you changed the be ... Riccar 8850 Vacuum

I am replacing drive belt on Eureka 4870 upright. Before installing I removed bottomplate and was cleaning out accumulated lint, hair and grit. Found a pair of identical (reciprocal) felt gaskets sucurely inserted above and below the roller brush, and one small loose piece of felt approximately 1/3 inch wide by 1 inch long that came out as I was pulling out debris. It has a slight crease across the middle as though I was not resting on an entire flat surface, but I find no other clues as to wher

If you go to this URL:\015\012\015\012http://www.VacPartsWarehouse.com/Eureka-4870-Ultra-Smart-Vac-s/1928.htm\015\012\015\012in the exploded view of the unit, identifying the parts and look at item 18, I believe it is where your felt part ... Vacuums

Hello, I have a Riccar 8000. The belt works, the bar spins, and it will **** things up. However, it will not pick up threads and dog hair or anything from the carpeting. Mu husband took the bottom off and there were a couple of small parts on the plate. We have no idea where they belong. Could not see them in the photos in the manual. Could it possibly need a new roller? Any help would be most welcome. Thank you! Mary Simon

... Riccar Vacuums

How do you install the 210-1128 Bissell carpet cleaner steamer brushroll on the Bissell ProHeat 8910? The prong on the replacement roller is larger in diameter than the one it is replacing. How do you open it up enough to remove the plastic piece that is attached to the steamer - the one with the belt??

Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 8910 ProHeat Clear View Upright Vacuum

Belt keeps sliding over on the roller bar and rubbing on plastic parts. Belt is a "U" belt and I am told it should be a "R" belt. Sears sold me a "U" so I will try and find the R tomorrow. What keeps the belt other than tension from sliding onn the roller bar? Could it be that just the wrong belt could cause this??

The 4870 Series uses Part number 61110. It is a "R" Belt. It will appear too be to large. This is normal. ... Eureka Smartvac 4870 Bagged Upright Vacuum

I am trying to replace my vacuum belt and can not get the roller brush to fit back into the slot after I put the belt back onto one end of the roller brush. Am I reassembling the belt and roller brush the right way?

If its a hoover or bissell, one side of the brushroll is slotted and slides. if its a eureka the hexagon end caps must be properly aligned, they go in at an angle. if its none of these provide me with the make and model # and i will give you a detail ... Vacuums

New Hoover belt nbr 385280-34 installed, belt still too loose.

There is no adjustment. As they wear they cut the groove in the roller deeper. Sure fix,and what Hoover will tell you to do is to replace the roller. If your like me though that isn't any good. so what I did was wind wax coated dental floss into the ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Hoover very noisy after new belt installed.

What is the belt # you have installed (generic)? Yes, there are problems with using generic belts on Hoover Vacuums. If you have noise I would suspect the roller, and replace it. the cost is about $25 and is something that you can install. The newer ... Hoover U5753-900 WindTunnel Bagless Upright Vacuum

The brush roller stops turning and I can smell the belt burning, then it will catch and start working normal. I looked under the plate to check the belts and they looked okay and no hang ups of string or anything. The only thing that seemed weird was that the smaller belt that actually attaches and turns the roller is a bit loose. The larger belt is tight but looks like its the one that is burning and causing the smell.

Better to replace both belts the smaller one is stretched out thats whyits slipping ,be sure to clean the old rubber off the motor shaft before replacing the belts.it will cause the new belts to run unevevly and go bad before their time ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Hoover windtunnel t series belt is loose- roller brush doesnt turn. Its brand new belt is slipping. we bough new belts and putthem on same problem. Can not find solutio in manual. Is the belt supposed to go around the "metal pulley". I know it goes around the little metal motor thing, then thru the guide and around the brush. What is the metal pulley??? Is is the larger round silver thing between the guide and roller?

I also have a loose belt and have bought additional belts but have the same problem. I put the it around the metal rotor and around the brush roller a shown by he Hoover video, and it is loose. ... Hoover S3765-040 WindTunnel Bagless Canister Vacuum

Belts Burning On our Ultimate G, belts are lasting about 2 uses and they smell and burn off. I am looking at the roller and I can see a slight grove where the belt rides. Is it time for a new roller. I am sick and tired of replacing belts and smelling up the house. Thanks Dusty

Yes, replace the brush roll, the ends or end is probably bad and causing the belt to slip and burn up. ... Kirby Ultimate G Bagged Upright Vacuum

My bissell 6590 works fine with hose attachment. Motor shaft turns when belt and roller are off. When belt and roller are on it's noisy and smelly. Now one end of the roller actually melted in the holding slot. Do these rollers wear out like this or should I be looking for another problem.

Replace the roller,belt and before instalation clean motor shaft where belt rolls. you can turn on the vacumm and using a knife scrape the motor shaft from the black dirt. ... Bissell 6590 CleanView Bagless Upright Vacuum

My Eureka Boss 4870 belt keeps fraying, stretching, and breaking. When I replace the belt and turn the roller brush by hand, within just a few turns the belt drifts off center and to the left of the roller brush where it starts to rub. How do I fix this?

... Eureka Smartvac 4870 Bagged Upright Vacuum

Eureka Model C2094-Type GW Vacuum 1 Bags-Belt- Beater Roller or bristles that go on roller-light bulb Vacuum 2 Bags-Belt-Beater Roller-Bulb-Plastic frame the motor bolts on-Metal holder the handle go in that lets the handle move up and down

... Eureka Vacuums

My vacume is less than 6 months old. I've gone through & replaced 4 belts. Now I realize the roller is not rolling which is causing the belts to break. The roller is free of all hair and debree. What should I do to fit the roller?

Very strong chance the end caps, made out of rubber could be a manufacturer defect. Many parts on vacs are made by different sources. ... Bissell Vacuums

Belt on Riccar 8850 is slipping off motor shaft.

NO! there is usually a fan attached to the motor. i have found that junk gets in there and will cause it to viberate. otherwise check the brushroll. there will be connectors on each side with a bearing. if the plastic looks melted, replace the brushr ... Riccar 8850 Vacuum

Kirby sentria belt install

How do i put the belt back on carpet cleaning attachment took it off to clean it and cannot get it backtogether ... Kirby Ultimate G Bagged Upright Vacuum

My Dyson Animal has good suction and works fine for actually picking up dirt, but when I use the vacuum with the roller, I hear a grinding/rumbling noise. Its only when I use the vacuum with the brush rotating. It does not happen hen I shut the roller brush off. The belt is fine. I cannot figure out what is wrong as there are no clogs, debris, or foreign objects stuck in the brush or in the belt. The noise seems to be the only issue. The vacuum picks up fine. It just doesn't sound right a

Trace the path of the suction into the tank and see if there is anything loose or ingested.\015\012Also, remove the brush and clean as best you can. Perhaps there is something caught in it. Lubricate where it makes sense with some WD40. ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

I have a DC14 with a bad belt to the roller.How do I remove the clutch that operates the belt to turn the roller. I am holding the assembly that houses the clutch and all screws are out, it appears the red knob that engages the drive to operate the roller brush must be removed. Please advise and how. Thanks, John.......[email protected]

You need a special tool to remove the clutch. Contact the Dyson Helpline so that they can refer you to an authorized Dyson dealer in your area who would have such a tool and who can fix it for you. The alternative is to purchase a tool and visit YouT ... Dyson DC14 Bagless Upright Cyclonic Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.3254 seconds