Having problems with your Riccar Vacuums ?

Missing ''vented support fitting and belt guard''

\015 Went to change belt in Riccar 4000 series vacuum, but the ''vented support fitting and belt guard'' (manual's words) was not there. Did it break off and get sucked up? Did I never have one? Do I need it???\015

Answers :

Repair Help & Product Troubleshooting for Riccar Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Missing ''vented support fitting and belt guard''

... Riccar Vacuums

Panasonic mc-e4113 Upright vacuum. The belt that drives the brush in front is broken I have found a spare for this but there seems to be a pulley missing on the main drive shaft that the belt needs to fit on. I can't believe that there wouldn't be one? Can anyone tell me if this is the case and if so where I can get one from. Many thanks Sean

... Panasonic Vacuums

Missing belt I have a Dirt Devil, Touchup, upright vacuum cleaner (model 084015). I need to know what belt fits this model.

Thanks for the info **** now stick it up your ***! ... Dirt Devil Vision Turbo W/Bonus Upright Vacuum Vacuum

Do you know where the vented support fitting goes on the Riccar 8925

... Riccar 8650/8625 s Vacuum

Hoover Wind Tunnel 7500 Brush not Turning. I have replaced the Brush and the belt. The problem does not seem to be either to me. I believe might be a missing part. The place were the belt hooks on is a metal pole which never seems to grip the belt well. In fact it seems loose most of the time and slips on the brush, causing the belt to eventually burn up. Could there be a missing plastic or rubber piece meant to hold the belt taught  on the metal pole?

Check the Idler Pulley part Number 43241004 (Item 13 in the IPB) ... Vacuums

Belt replacement appears to have 2 belts, 1 is on and 1 is missing, the belt that is driven by the motor is missing, how do I remove the clutch housing where the belt goes?

Hi.\015\012\015\012You are correct there are 2 belts.\015\012They can be tricky to replace most shops will state they cant be replaced & you require new clutch.\015\012So try this site ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Trying to fix new belt to Hoover Turbo Power vacuum cleaner. Don't see how the belt becomes taut. Fitting it around the roller, there is nowhere to fit the belt to, it just sits loose.

I looked at the user instructions guide online and saw where the 'other end' of the belt should be fitted. It was extremely hard to fit but eventually managed it. Thanks for this solution site. I wouldn't hesitate to use it again. ... Hoover U5396-900 Turbo Power Vacuum

Just tried to fit a new belt to a vax quicklite 2 upright hoover and the belt snapped is there a right way to fit belt

... VAX Appliances Vax X3 Bagless Upright Vacuum

I'm trying to use the reverse flow hole on my Miele s712 to blow up an air mattres. None of my fitting appear to fit so I can use the hose. Is there something I'm missing? Is there a trick of the trade? Or am i missing some gear. It's new, out of the box but I just can't get the hose onto the reverse flow. The Poduct is a Miele S712 vacuum dispite what this system has allowed me to enter. ; )


Dyson fan belt fitting. i've lost my manual for my dyson animal dc07 and need to fit a new drive belt. thanks in advance, alan

You can see this on utube video. help ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

I'm using (or WAS using) a Eureka ''the boss'' model 8803. The belt broke, no biggie, so I replaced it with a Eureka model U belt, the problem is when I put the new belt on and turn on the vaccuum, the belt breaks again. I am also having trouble getting the brush roller to fit right when the belt is in place. I can't find any sharp edges that would cut the belt,nor can I find where any small bits may have broken. Anyone have a solution for me?

First, make sure you have the right belt, second, i am thinking that you are not lineing the roller up right, it will only fit one way. look at the ends of the roller and the grooves where it slides in, you should be able to see clearly how it goes. ... Vacuums

My bissell brush band has come off and wont stay on thus the brush will not turn, there is also a black arm type thing on a spring inside (on both sides) on the pump belt side it has broken - the side where the brush belt is, help im searching for parts and a way to fix it but im getting no joy, incidentley the brush belt thickness looks way to thick for the small thickness for the brush belt cog (?) to stay on........am i missing something? so i need to get the arm thing replaced plus find a

... Bissell ProHeat Deep Cleaner Upright Vacuum

Small belt driving the brush...stretched out with hair accumulated in groove beneath belt. Is there a clutch or other means of tightening the belt. Went to store found belt...same size, therefore previously assumed stretched condition does not appear to be valid. I'm missing something. Any help?

You do not by a belt by size, buy it by model only. A new Hoover belt will generally be very snug when installed. As heat builds from use it stretches and becomes worn sometimes as much as 30% oversize. Good that you have cleaned out the hair. Check ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

I put both belts on my U6634-900 and i can make brush spin manually, but the small belt looks to big, not fitting snugly and not turning brushes when i give it juice. Yes I have the right belts.

... Hoover U6634-900 WindTunnel Bagless Upright Vacuum

Oreck vaccum when i put a new belt on, the belt rubs the side of the wall of the vacuum gets real hot and busts. is there any type of washer fitting that goes on the vacuum to hold the belt in place? i dont know i need help thank you. you can reach me at [email protected]

The belt must not be running true to the pulley. You may need a brush roll, but also check the motor to make sure it isn't moving inward after the belt is put on. ... Oreck XL Ultra Bagged Upright Vacuum

My Hoover Wind Tunnel Bagless Pro Pet is making a very loud thudding noise when the belt rotates, belt seems to be intact and in place, what am I missing? Vacuum is less than 6 months old, belt is not worn and motor seems to be fine.

... Vacuums

Trying to replace belt on hoover convertible bagless upright u8188900. belt replace # 38528-049. i have opened vacuum and put belt back on, but it will not get tight enough around the motor gear and the brush spool to be able to activate. am i missing something? mike

... Hoover Vacuums

I have a dyson root cyclone. i dismantled it to replace the belt, it is not the belt which is on the roller brush, it is the belt which is from the motor, it was easy to take out as it was broken, i will get new one tomorrow now im wondering how do i fit it in.

The belt that fits on the motor is the same belt that drives the roller brush, all you need do to gain access is remove the sole plate, normally attached with 3 quarter turn connectors, use large flat screwdriver to turn them ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Replacing a belt on the Riccar 8850...I see how the brush assembly will work with the new belt. But I don't see how a new belt will turn on the small rod extending from the motor. Is there a pully missing?

There is not a pulley missing, when the belt is tight the shaft will turn the belt but when the belt loses elasticity it will slip on the shaft when being used on the carpet. Replace the n\012belt at least once or twice per year. ... Riccar 8850 Vacuum

Bought a new sweeper and brush ( beater bar ) does not turn. The large belt is fine and turns. The small thin belt is also fine but does not turn the brush. It is either the wrong belt or is there something that could be missing to put tension on it ?? Thank You [email protected]

Jim, To put tension on the brush, tilt machine forward when upright, move carpet selector knob to carpet. then turn vac on. Brush will only spin when vac is tilted back to operate. brush stops when upright and on to use hand tools so the er is no dan ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

I am trying to replace my vacuum belt and can not get the roller brush to fit back into the slot after I put the belt back onto one end of the roller brush. Am I reassembling the belt and roller brush the right way?

If its a hoover or bissell, one side of the brushroll is slotted and slides. if its a eureka the hexagon end caps must be properly aligned, they go in at an angle. if its none of these provide me with the make and model # and i will give you a detail ... Vacuums

Bissell 6595 problems with roller brush. I've had this happen with two of the same model. Each one didn't last more than seven months! First, it became loud when vacuuming, then there was a burning smell. When you try to replace the belt, you see that won't do any good because the fitted end of the brush is melted. The housing part the roller brush fits into is melted too. There's no place for the roller brush to fit into. I tried to upload pics, because I don't see how replacing the roller brus

... Bissell 6595 Lift Off Bagless Upright Vacuum

How to install the belt on U8188900. It has a cam on the electric motor where the belt gos and there is a center looks like a pully and the part where it fits on the brusher. How do you get the belt around the center pully?

... Hoover U8188-900 Bagless Upright Vacuum

Fan belt wheel missing. Took it apart and discovered fan belt torn and no wheel on drive shaft for brush. I am assuming that there was one there originally.Did it shatter or what.What is solution. Can I get exploded view of this model or others like it.

Get another fan belt wheel of the model and place it over it ... Vacuums

My Panasonic model MC-V6830 works but no suction. I checked and belt was loose, but there is nothing to attach the back of the belt onto. Seems some screws or plastic pully part/parts are missing. What parts do I need to order to fix this vacuum?

... Panasonic Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0555 seconds