Having problems with your Riccar Vacuums ?

I have model a Riccar 8905 upright vacuum cleaner. When changing the belt a part fell out and I don't know where to put it or what it does.


Answers :

Repair Help & Product Troubleshooting for Riccar Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have model a Riccar 8905 upright vacuum cleaner. When changing the belt a part fell out and I don't know where to put it or what it does.


... Riccar Vacuums

My belt broke...I bought a new belt..but I do not know how to put the new on on. I took out the brush roller and put the belt around it but I have no idea how to get it to go on the part that makes it move.


Hello,\015\012Here is a link to my free online guide...\015\012\015\012http://reviews ... Kirby Ultimate G Bagged Upright Vacuum

Hello, my names Travis. I was contacting you in concern of my Kenmore Quick Clean 12AMP Vacum Cleaner. My girlfriend took the bottom off the vacum and removed the belt because the vacum wasnt picking up. I know have a new belt i just dont know where to put it on the vacum to reinstall it


Look for grooves on the motor shaft and on the brush shaft. ... Kenmore Quick Clean 30012 Vacuum

I have a Hoover Slider, Model #S2105, Serial #050500084989, and I need instructions on putting it back together; with parts and assembly of parts. I took it apart because it was making a noise, and I believe one of the belts had come off. However, when I took the screws out of the bottom to check the belts, the whole thing fell apart. Now I can't get back together properly. It will not come on, and I believe it is because the switch that makes it come on when you lower the handle is not posi


Greetings from GoVacuum,\015\012\015\012Please see the link below for a parts schematic to your Hoover Slider, hopefully this will help you put the machine back together. If you find a part that is missing, and would like to order one, j ... Vacuums

A small belt fell from underneath my bissell steam cleaner and I notice the brushes no longer rotate when I purchase the part where does it go? I tried turning it up side down to find out where it came from don't know because there is a compartment for the belt access but that particular bet is not broken. It's a very thin belt I can not make out the number located on the belt please help.


If you are unsure about where it goes it may have a diagram in the owners manual. When you say you saw a belt in a compartment are you sure that it is not an extra belt you are seeing as they often give an extra in the machine kept in a compartment l ... Bissell 1697-7 Powersteamer Pro Deluxe Vacuum

Oreck vaccum when i put a new belt on, the belt rubs the side of the wall of the vacuum gets real hot and busts. is there any type of washer fitting that goes on the vacuum to hold the belt in place? i dont know i need help thank you. you can reach me at [email protected]


The belt must not be running true to the pulley. You may need a brush roll, but also check the motor to make sure it isn't moving inward after the belt is put on. ... Oreck XL Ultra Bagged Upright Vacuum

I can't seem to get the belt cover off of my Kenmore Progressive 400. There are two buttons that say above "belt and bulb change" but the buttons do not move. Do you know how I can remove so I can put a new belt on? Thank you!


You have to take off the top of the power nozzel that has the light lense. There are two pressure locks,one on each side. Use a screw driver to release. You will see the screws.Take the two screws out and on some models, there are two pressure locks ... Kenmore 23612 Progressive PowerMate Bagged Canister Vacuum

While putting on a new belt for my Turbo 4000 Hoover upright vacum cleaner, the parts for the height adjustment (slide bar)fell apart. I'm hoping that you might have a diagram or detail instructions on how to put together again. Thank you


... Vacuums

Belt broke I have a bissell powersteamer and a belt broke and came out the bottom of it. I dont know how to put one back on it


There should be an access panel on the top side of the cleaner. Pry this open with a screw driver and this should get you access to the area where the belt can be changed. ... Bissell 1698 PowerSteamer ProHeat Upright Wet/Dry Vacuum

I have a self propelled Royal Dirt Devil vacuum model number 087900 and it goes backward fine but forward has to be pushed so hard it's impossible. Is this a switch? Do you know about how much the part would cost and can it be done by a beginner. We fix a lot of things ourselves but we aren't mechanics by no means. We put a brand new belt on it. I don't think it can be put on backwards and brush turns fine. Where is the switch? Use layman's terms.


You might try a new belt and/or brush roll. The brush roll is what helps pull a vacuum forward, the power drive helps, but if the brush isn't turning like it should, then it will hinder forward motion. The belt may look ok, but they stretch to the ... Vacuums

Belt I have a bissell pro heat model number7901-1 and i dont know how to put the belt back on. The old one broke and i cant find my book.


First take off the cover on the left side of the top cover, then turn it over, remove the screw holding the red lock and pull the cap and brush roll out, remove the cap, remove the cogged belt, then you can put the new pump belt thru that slot, put o ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

D.d vaccum i have a dirt devil dynamite...i bought a new for it i put it on and not even 1 minute of using it the belt broke again!!!!i dont know whats going on do i have 2 put it on a certain way does it need grease or what!


Did you check the brush roll, if the ends aren't turning freely, then it needs to be replaced also. ... Dirt Devil M084600 Dynamite Bagless Upright Vacuum

Changing belt i do not know how to put the belt back on.


Here is a video how to change belt on kirby vac ... Kirby G6 Bagged Upright Vacuum

DONT KNOW HOW TO CHANGE MY BELT


Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=698891\015\012Generic problem for all Vacuums\015\012DONT KNOW HOW TO CHANGE MY BELT\015\012Posted by m ... Vacuums

Dont know how to change the belt on a 1697 bissel powersteamer pro


There is a great video on the Bissell site. 1 min watching it shows you how.Basically you unplug it, take out the tanks, turn it upside down, remove the 2 red clips that hold the brush assembly, and lift the assy out, then replace belts. ... Bissell 1697-7 Powersteamer Pro Deluxe Vacuum

Plug Part # 8191782 on my kenmore vacumm wand is bad, I dont know how to get the wand apart to change it


... Kenmore Vacuums

My belt fell off and i need to know how that and the brush part goes back on


You need to refer to the video to help you if you haved it other wise it can be done by turning thr plastic nob which is almost flat on the fro\\nt of the head. turn it all the way to the left and thyen push the ... Kirby G5 Bagged Upright Vacuum

I have a Fantom 500 DX and it seems that it doesn't pick up anything anymore. It looks like machine is working well, but it doen't pick up. I would like to take to the repair guy, but I don't know where to find one. Machine is good, it might need jsu some maintenance. Please advise. I live on Long Island, NY. PLease advise. I changed the belt about 6 months ago, but all other parts are original.


The type of bagless that has sharp turns in the hose and plastic parts are easy to become stopped up. You have to follow the path of the air flow to find the blockage. ... Fantom Vacums FM760 Twister 500DX Bagless Upright Cyclonic Vacuum

Dont know how to change belt on bissell pro heat carpet steamer cleaner


See thishttp://cache.vendaria.com/vpop/VpopV6.html?ct=13&ctname=CT630X556D630X390&fw=630&fh=556&logo=49&fv=10&ap=vnd_bissell_deap_cleaner_how_to&purl=MAIN_bissell_how_to_replace_upright_deep_cleaner_belts&i ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

I am trying to replace the pump belt on my Bissell Proheat 12 AMP moedel #7901-9. I was told this was the easy one to change, but it is only if you know where it goes and how to put it there. Can you give me some help? Pam


Here is a link to where you can view the manual. Hope it helps!Bissell ProHeat Belt and Manual ... Vacuums

I need to change the belt on my Bissell Pro heat. I dont know how to get to it!


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

I have a hitachi 1300 upright hoover and dont know how to change sdrive belt


... Hitachi Vacuums

I have a dc07 green and silver dyson and i dont know how to put the belt on


Go to www,dysonmedic.com then scroll to the bottom of the page and click on "DC07 belt and brushroll replacement guide". You will find an excellent illustrated step-by-step guide ... Dyson DC07 Bagless Upright Cyclonic Vacuum

How do i use the shampooer on kirby i have so many parts and dont know wher to begin to put them


I would contact Kirby directly:http://www.kirby.com/Portals/0/contact_us.html ... Kirby Ultimate G Bagged Upright Vacuum

I dont know how to change the belt on my hoover turbopower 4000


... Hoover U5264-930 TurboPower Bagged Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0989 seconds