Having problems with your Riccar Vacuums ?

I need to replace the switch and leads to my Riccar 1500p vacuum. I've already replaced the entire electric hose which is over $100. Where can I get the switch and leads?


Answers :

Repair Help & Product Troubleshooting for Riccar Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I need to replace the switch and leads to my Riccar 1500p vacuum. I've already replaced the entire electric hose which is over $100. Where can I get the switch and leads?


... Riccar Vacuums

The switch to my Riccar 1500p hose is broken for the 2nd time. I don't want to replace the entire hose again, where can i get the switch and leads?


Take the screws out to take the handle apart. Remove the switch and take it to your hardware or local vacuum to to get the correct replacement. ... Riccar 1500 Simplicity S24 And S20 Electric Suction Hose Assembly

My Shop Vac 90L600A is getting electric thru the cord and into the switch, but it doesn't switch on when you toggle the switch from off to on. Is it a bad switch?


Check the othere end of the switch. You may have a brushes problem in the motor. You will have to check the switch while hot - be careful ... Vacuums

I have an Easy-Flo central vac unit. The handle on the electric hose has a switch on the handle. With the switch on ''O'' in the center, it's off. On the left, is the ''I'' position. The vacuum runs but the power brush doesn't. On the right is the ''II'' position. The switch won't flip that way. It feels stuck. It feels as if there is something underneath of it that won't let it push that direction. I have the switch out of the handle, but I can't seem to get the actual black casing around the


Switches are not usually designed to be dissembled.I would strongly suggest that you dont take the switch apart. you are better off getting a new one. then if you feel like it you can take the old switch apart and if it dosnt work you still hav ... Vacuums

I was changing a light bulb with one of those metal extension rods that unscrew and screw back in the replacement bulbs. It evidently didn't seat correctly and pulled off the bulb and created a quick "poof" type electrical short. I have switched out that bad bulb with a new one and can't get either the fan or lights to work. There doesn't appear to be a reset switch. I also swirched out the wall switch to see if that would make a difference and it does not. Any thoughts or ideas would be appreci


If you have not already done so, I would check at the fuse or circuit breaker panel to see if you have blown a fuse or tripped a breaker. ... Vacuums

Am attempting to get 'inside' the vacuum to troubleshoot why it suddenly stopped running. Suspect it may electrical, and have already checked the obvious (visible cord and plug.) However, there doesn't seem to be an obvious way to get inside the canister without destroying something. Thanks!


Hi There,\015\012\015\012Here's a link to a repair solution that I've done explaining how to diagnosis the cord reel, and open up the machine. The model this is done on is not the same exact model as yours, but the repair will be almost ... Miele S251 Flamenco II Bagged Canister Vacuum

GE on/off timer for a bathroom fan - switch has four wires Green - ground White - neutral Black - power Blue - lead My fan has two - white neutral and black lead I have tried every configuration and cannot get the fan to work. Any suggestions?


I would guess that the black wire on the timer is the power in and blue is the power out to the fan (hook it to the black wire going to the fan) The other colors are right. ... Vacuums

Have DC07 that won't come on. Wife said this started happening a few weeks ago. Would come on and then other times would not come on. Now will not come on at all. Believe I have a lose wire. Have taken off star screw by on off switch, but cannot find how to get plastic parts apart to get into electrical connections. How do I do this? I am sure I am missing something simple?


... Dyson DC07 Bagless Upright Cyclonic Vacuum

My nearly new Miele S710 vaccum cleaner just revs like mad when you switch it in but you get no suction. Could there be a drive belt between the electric motor and the vaccum pump that has come off or broken? How can I get at it, if this is the case?


Hi,\015\012\015\012Yes this could be a case due to which there is no suction. I am posting an article which gives you a detailed description of how to open it and repair the internal parts.\015\012\015\012 ... Miele Vacuums

Oreck model BB870-AS - I was vaccuming when the vac shut off. The motor just spooled down and nothing more since. I have opened the case. Have power at the switch, and to the motor, but can't get a voltage reading to the common lead at the motor. Is there a fusible link, or something similar in that lead that might have burned out? Thanks!


... Oreck Vacuums

Hi, I have a Eureka model #4472 does have a bag. The power switch would only go on if I held the vacuum handle almost to the floor and now it doesn't go on at all. We already paid to get it fixed once already. Please help


... Eureka 4472 Vacuum

The power head of my DC 21 keeps cutting off as soon as I start moving the hose around. The only way to get it going again is to step on the main switch on the canister, then the whole cycle of off and on starts again. I have replaced the entire power head and tested the continuity of all the wires in the hose and they are good. The repair shop says the PCB is bad but can not get one. What can I do ?


Not much. my only suggestion is to dig through the internet and try and find that pcb it may take awhile but it would be worth a shot. if you dont think you can make the repair take it to repair shop with new pcb and let them do it. ... Dyson Genuine DC-21 "Stowaway" Spare HEPA Filter, Dyson

I have a powerhouse electric heater #NPH4AB and I need a on-auto switch which is bad where do I get one?


... Vacuums

Shark Euro-pro EP621 Bagless Upright Vacuum. Q regarding the brush not spinning / after troubleshooting and taking actions listed below, it now spinning for a few secs, but then stopping. Already removed hair, strings, etc. Checked that belt is aligned properly, checked that small wheel that turns belt is working (spins fine when belt removed. Oiled the turning parts a bit, that made it spin better, but still stops. It turns about 3-4 seconds then stops. If I switch it off and on again, I get ag


... Euro-Pro EP621 Bagless Upright Vacuum

I can't get the power switch on my DC25 to turn the vacuum off. I have to plug it in to the electrical socket and then unplug it to turn off. Suggestions?


It's probably the on/off switchI found a cool hint at http://www.fixya.com/support/t7785183-trying_remove hope this helps you ... Dyson DC25 All Floors Bagless Upright Vacuum

I have a Wertheim 4808 Barrel vacuum cleaner that has suddenly stopped working. I believe that there is a problem with the electrical cord connection inside. I have tried unsuccessfully to open the compartment that leads to that area. One side unscrewed with a phillips head screwdriver but the other side seems to have a different type of fixing screw that I am unable to undo. It is awkward to get at and in a deep slot and the head of the fixing screw? is not visible.


... Vacuums

Switch I have a kenmore 31913 vacuum and the on/off switch appears to be bad. My problem is getting into the switch. How do I open up the handle to get to the switch?


Go to this website\015\012and enter your complete model number in the search field in the upper\015\012right corner of the page. You should be able ... Kenmore 31913 Progressive Direct Drive Bagged Upright Vacuum

The handle for my Eureka 5993 AVZ was getting very hot when used. Finally, the wires around the switch melted and now the vacuum will not work. What is wrong? Is the switch bad? The wires only melted in the immediate vicinity of the three-prong switch. Nothing else appears to be wrong; the vacuum worked fine when it was running - except for the handle getting hot. Thank you!


Try cleaning all...\015\012if have sam paoblem need replaced main motor.... ... Eureka 5893AVZ Bagless Upright Cyclonic Vacuum

Replaced Oreck power switch. 2 black leads and 1 white lead for switch. Posts marked 1, 2, and 3. 2 black wires to switch powers on. Connect white wire and breaker trips. Where does the white wire go?


Both black go to the switch. Power in - black to switch / white to white from motor. From motor - black to switch / white to white from power cord The black wire from the power hooks to ... Vacuums

Eureka Vacuum Excalibur Model 6975A on/off switch won't turn off. Probably need new switch but can't figure out how to get cover off to get at switch


... Vacuums

My Rexel shredder isn't switching on when connected to the electricity. I've tried all the settings but the machine won't switch on. I've cleared the shredders, checked the bin is in correctly, tried different electric points.


... Vacuums

I have a replacement switch. How do I get the cover off to get at & replace the defective metal switch? Thanx Pete Potter


Hi, you need not to do this yourself, just take it to a electronic repairer around you to take if off and replace the defective metal rather than stress yourself...Take care ... Eureka Sanitaire S661 Bagged Upright Vacuum

I have a Z5930 vacuum and i want to trace an electrical fault. I need to disassemble it to get to the electrical connections and it is quite a tricky one to get in side. The machine will run and then cut out after a short time. It will then re-start in about 2-3 minutes and run normally again and so on. I was not able to give you the exact model but it is Ultra Filtration Oxygen line


... Electrolux EL7020A Oxygen 3 Ultra Canister Vacuum Cleaner Bagged Vacuum

Power Switch How do I get the power switch out to replace it? I have a D4C model. Rainbow/Rexair. Is there a place where I can get a parts breakdown of the vacuum cleaner? Steve


This is not that hard:1. - remove gasket (it is glued so you may end up damaging it)2. - remove 4 screws holding baffle 3. - under it yo ... Rainbow E series Canister Wet/Dry Vacuum

We have Nilfisk Tempest 1500W bagged cleaner. It just stopped working and I have taken off top cover and all wires/contacts look OK. But power still not getting through I assume. The retractable lead goes into base and cant get to this area. How do I check main lead or perhaps you provide details of serviceman. On North Shore, Auckland, NZ.


... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0555 seconds