Having problems with your Riccar Vacuums ?

On off switch does not work riccar 4812 - Riccar Vacuums


Answers :

Replace the switch
Repair Help & Product Troubleshooting for Riccar Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

On off switch does not work riccar 4812 - Riccar Vacuums


Replace the switch ... Riccar Vacuums

The handle for my Eureka 5993 AVZ was getting very hot when used. Finally, the wires around the switch melted and now the vacuum will not work. What is wrong? Is the switch bad? The wires only melted in the immediate vicinity of the three-prong switch. Nothing else appears to be wrong; the vacuum worked fine when it was running - except for the handle getting hot. Thank you!


Try cleaning all...\015\012if have sam paoblem need replaced main motor.... ... Eureka 5893AVZ Bagless Upright Cyclonic Vacuum

Kenmore canister vacuum model 116-25512506. It has a 2 stage switch on the handle, the vacuum motor will not work, the carpet beater attachment does work, the vacuum motor will not cut on at all with either stage, 1st stage is vac only, 2nd is vac a carpet attachment. Carpet attachment will work, vac does not.


Try to find the reset button. It should be somwhere near the bottom area. It looks like a red dot that you can push inward. If you can press and hold the reset button, it will restart your suction and solve your problem. ... Vacuums

On/off switch we have two of these vacuums at work, and both of there on/off switches dont work too well. its hard to explain, but when u normally turn it on or off theres a little resistance in the switch and you hear a click, with both of ours the switch moves freely back and forth from on to off, no resisntace, no click, and the machine doesnt stay on, or off for that matter. the switch just moves back and forth.


... Eureka 2991AVZ Bagless Upright Cyclonic Vacuum

Brissel Healthy Home Hepa Vacuum: On/Off Switch works sporadically. Took handle apart and the switch worked for a while. I am wondering if I need to replace the switch? Also the Brush Switch is having similar problems.


Might not be the switch there is a connection on the swivel by the base that likes to fail ... Bissell Healthy Home HEPA Bagless Upright Vacuum - Metallic Blue

Vacuum dead I have oreck XLx2 bagged upright - the belt ,plug and cord have been replaced - has been working great - now went to plug it in and it does not work - the light goes on in the on/off switch so power is working but vacuum is dead - any suggestions


If the cord coming from the bottom up to the handle is loose, and is a plug, push it in. If that doesn't help. then could be a problem with the motor. One other thing to check is inside the handle, maybe a wire came loose. ... Oreck XL2200 Bagged Upright Vacuum

Halo vacuum The rollers on my Halo Vacuum will not turn. I turn on the switch below the on/off switch and nothing happens. The vacuum is working. Just no rotation


... Vacuums

I have a Eureka Upright vacuum (4800 Series). When I try to start it by turning the switch on, it wont. For few days, I was able to get around this problem by repeatedly turning the switch on and off until it turned on but that does not work any more. Could it be something related to the switch it self or the power cable. My wife mentioned that one of my kids might have pulled the power cable too hard (at the back of the vacuum). Any help to solve this problem will be very much appreciated. Tha


... Eureka Smartvac 4870 Bagged Upright Vacuum

I have a Craftsman wet dry vac with blower capability (22 L). While I was using it to **** up water, the water came out of the blower hose. Now I can't get it to work as a vacuum. What can I do to fix this problem? Is there a toggle switch somewhere that allows me to choose vacuum or blower? Also, will the vacuum still work without the filter nut attached to the plate? Please let me know at your earliest convenience. Thank you.


... Craftsman Vacuums

I was vacuuming and my electrolux 2100 accidentally suctioned the string attached to a balloon. I turned off the vacuum and unwrapped the string from the head of my vacuum. On the hose i have plenty of suction but the head isn't working. i flipped on and off the emergency shutoff switch but it is not working. what happened? what can i do?


... Electrolux UltraLux 2000 Bagged Canister Vacuum

I have a Rug Doctor ez-1 that the vacuum only works through the upholstery tool and not underneath. The underneath vacuum only blows air outward. I have switched the carpet/upholstery switch depending on what function I'm using but still no suction on the floor. Any ideas?


... Vacuums

Wiring the switch for a kenmore vacuum cleaner I need to know where teh different colored wires go. It had a short in it so I replaced the plug but think I wired it incorrectly. Its a Whispertone 300 model 116.28612790 The canister works but the beater bar doesn't.( it worked before a rewired the switch. Thanks


... Kenmore 23313 Whispertone Bagged Canister Vacuum

110-220V Dear Sir, I purchased a kirby sentria vacuum cleaner from ebau two weeks ago. I currently resid in the UAE with 220V power. My maid has plugged the vacuum to work with it unaware of the voltage difference, a terrble noise as mentioned came from the cleaner as well as a smell. She unlugged it and stopped t from operating. Can you please let me know how can i assess the damage? If this model has a switch from 110 to 220V IS there a solution with transfromer or motor to make it work? Thank


You may have burnt up the motor field when it was plugged into a 220V power source. But there are drop down transformers you can get to reduce the voltage form 210 to 110. AS Radio Shack or similar store would have them. ... Kirby G4 Bagged Upright Vacuum

Now that I just fixed my Lux Legacy canister vacuum, I need help on my other Electrolux Regency Series upright! The vacuum works fine but the rotating brush does not work and the brush motor does not turn on. Tried cleaning the brush and hitting hte reset button to no avail. This upright has a triple setting switch and I checked the each of the wires seem to be attached. Tried rotating the brush by hand and it would not budge. Was going to "encourage" the brush to turn with a set of articula


There are a couple rectangular holes on the bottom of the power nozzle, beside the wheels. These have tabs in them that need released with a standard screwdriver. \015\012 ... Vacuums

My lux 7000 has a new bag but when i start to use it with the power unit or without the unit shut's it self off i can reset the lites or the motor if you will by clicking the on off switch 4or 5 times and i'm ready to go again untill you start to work and off it goes you can repeat the switch thing as long as u want, it just won't let u vacuum ,it turn's it self off .I blew it all out but found nothing in it. if u don't try to vacuum it will run as long as u want to listen to it. Can you


Have you replace the afterfilter? It may also cause this if rather dirty. It's located under the tool caddy/air diffuser on the back half of the machine.\015\012Try this: Disconnect hose, turn on vacuum. Does it continue running? If so, pl ... Electrolux Lux 7000 Bagged Canister Vacuum

My Dyson DC25 animal is having issues. I believe everything is working correctly except I have realized that the mechanism which switches the hose/valve between the wand and the vacuum head isn't working properly. The two gear pieces that move the hose placement aren't close enough together, so they don't work together. It looks like there is a washer that I could potentially remove on the clear gear piece which would allow it to sit closer to the assembly. Would that work? Currently I am


... Vacuums

The switch on our Hoover Windtunnel vacuum cleaner is not working. I have located the replacement part on your website...part#Ho-28161067, I've removed the wires from the switch. Is there any trick to actually removing and replacing the switch itself? It seems to be in there rather tight.


No, follow the directions to replacing the switch and you should be good. if you got the kit then splice the wires and replace them with the wires profied and the wire nuts, you should be good. ... Vacuums

Hello! I have a Rainbow vacuum Model# D4C that needs a switch. I am only able to get the new style 4 wire switch and it has the 6 wire. Can I make the 4 wire switch work in place of the 6 wire?


... Vacuums

Our Kenmore Vacuum Model # 116.22950 will not turn off at the switch. I have to unplug it to stop the machine. My husband just tried to replace the switch on the handle but this did not work. We got a new switch.


... Kenmore 2029915 Canister Vacuum

Dewalt DEWALT Cordless/Corded Wet/Dry Vac 2 Gallon Vacuum: It was purchased new, and used only one time,the second time the unit was turned on it never worked and have never worked since, the motor and switch were both tested and are working...any ideas?


This vacuum has a history of problems with the battery contacts. Check that yours are not bent out of shape or corroded. if they are... straighten them or remove the corrosion. ... Dewalt Cordless/Corded Wet/Dry Vac 2 Gallon Vacuum

Vacuum Power Switch on Handle Doesn't Work


The switch is very cheap. I have the same vacuum. The solution is to stick a thin peice of cardboard under the slide track for the rod in the handle assembly. You will see the rod when you disassemble the handle for the sweeper. Move the on/off switc ... Vacuums

On-off switch on vacuum cleaner does not work


Model no. on Vac. U6476-910 Switch does not work. Please advise. Help. ... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum

My Vacuum just stop working. I was cleaning my car carpets when it just went off. I tough it got disconnected from the outlet (power supply). The vacuum was connected and it is like when a fuse go bad, just like that it won't turn on anymore. Is there a switch that needs to be reset or a fuse to be replace? How do you do it?? Thanks


There is not any of that. Buy a new one ... Hoover Empower Bagless Upright Vacuum

Power head attachment works great when plugged into the hose part of the vacuum. The problem is when I attach it to the tube for normal use there is no power. I have checked all the connections and switched the power switch on and off still no power from tube to power head. Is there anything else I can try? Model Callisto


Try having someone turn the machine on and off while you pull the cord in and out with the cord more angled towards the on/off switch. Sometimes these models have a break in the cord rewind and will not put the power through to the motor. ... Miele Vacuums

Our Proteam ProForce 1500 is 1 year old. The vacuum works (****) in the hardwood floor setting on the switch. The beater works on the other setting but it won't **** and beat at the same time. What is wrong and is it something I can fix?


It may be something to do with the actual switch on this unit. \012\012I have a feeling it may have to do with the wiring on the switch itself, perhaps one of the wires have come off or burned on the contact. \012\012Is it som ... Proteam ProForce 1500 Bagged Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0780 seconds