Having problems with your Riccar Vacuums ?

Riccar 1700 melted connector to circuit board...

\015 I opened up our 1700 and found the power connector to the circuit board melted... I checked the resistance through the power chord and cleaned the fuzz that had accumulated on the chord winder unit. The connector from the spool to the circuit board showed signs of overheating and the solder joint on the circuit board itself broke loose while trying to disconnect the locking connector. Will I be ok directly soldering the wires to the circuit board or is there likely to be some other issue causing the wires to overheat?\015

Answers :

It might be an easy fix but should be done by a qualified Riccar dealer.
Repair Help & Product Troubleshooting for Riccar Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Riccar 1700 melted connector to circuit board...

It might be an easy fix but should be done by a qualified Riccar dealer. ... Riccar Vacuums

I have replaced the circuit board twice on my hayden 2400 and after working for 24 hours the circuit board then fails, with no signs of it tripping. Everything is wired in correctly the supplier is unsure of the problem but leading up to me replacing the circuit board the machine itself had became intermittent switching on and off while hoovering

Disconnect the wiring from the unit, and go back and plug in your hose. \012\012Get a volt tester and test the voltage coming from the lines at the machine. It should read 0 volts. Check both AC and DC voltage. \012\012Also, c ... Hayden Industries SuperVac 2400 Central System Vacuum

I have an Eureka Express canister vacuum - I believe it's model 8284 - that just stopped working. Plug it in, turn it on, and absolutely nothing happens. I took it to the local sew and vac place and they say it's a circuit board that is no longer available. I've looked at all the parts lists and diagrams for that vacuum and I would swear there isn't a circuit board there. (I wouldn't have even thought that in 1989 they would have used circuits.) In any case, I absolutely love this machine a

Given the age of the machine weighed against you fondness for it, unless you can find a fault with either the switch or the cord, there is little else that can be done. With time the electrical lead can break down and one o ... Electrolux Vacuums

Have a Miele S658 Blue Moon that cuts out intermittently, sounds like most of the solutions to similar problems indicate the circuit board has gone bad in the hose mechanism.......can just the circuit board be replaced or does the entire hose have to be replaced?

Probably needs a new hose. ... Vacuums

My circuit board has a short on the soldering for the DC rectifier that supplies the carpet cleaning motor. Where can I order a new circuit board. Miele S251i

Just a suggestion, but you could try to re-solder the connection on the board. some of the circuit boards did not have enough solder on the board coming from the factory. That being said, if the component is damaged due to the burning, I ... Miele S251i Plus Bagged Canister Vacuum

Dc15 fuse The roller brushes on my dc15 stopped working..I checked the obvious and then noticed that the 2 amp fuse was blown on the circuit board . I've replaced it with the same type bought from Maplins but it keeps blowing .. I tested the yellow an blue wires leading from the circuit board to the roller brush head and the are in tact and I can run a current through them ... Any thoughts from anyone .? Your help would be. Appreciated thanks Lee

Hi Lee,I'm sorry to hear you're having difficulty with your DC15. If you'd like some help, please give us a call on 0800 298 0298 - we may be able to resolve the issue with some troubleshooting over the phone.Best wishes,Jack ... Dyson DC15 All Floors - The Ball Bagless Upright Cyclonic Vacuum

Circuit board i have searched far and wide looking for a circuit board for my fantom cyclone xt, so far i can't find one .. is their anyone who can can locate or sell me one of these hard to find items. i am at the end of my rope ! any help is appreciated, thank you for your time TOO SLIM

Http://www.vacmall.com/supplies.asp?Brand=Fantom&Model=Cyclone+XT ... Fantom Vacums Cyclone XT Upright Vacuum

My danby kegerator model DKC645BLS controller circuit board corroded and no power to the compressor,I already have an external temperature controller,can I just bypass the controller and circuit board

... Vacuums

The battery will not charge in the sweeper. I can remove the battery and wire it to the power supply for charging and it will charge up and run the sweeper. So the power supply and the battery are both good. Obviously there is a circuit failure in the on board charging control. Anyone know a fix or a likely faulty component? I had a shark handheld about 8 years ago and it developed the same problem. I examined the little circuit board inside but saw no visible indications that would isolate t

... Euro-Pro Cordless Bagless Upright Sweeper - Blue/Gray

My wife's Viking 6690 smoked this last weekend. I opened up the end where the power switches are and the board had a 0.01 ufd capacitor the blew up. That would be easy enough to repair. However when the Cap blew, it also fried a small quarter watt resistor that sits just under the upper white pin connector on the board. The resistor is burnt beyond recognition and I am trying to find its value. Is there a schematic available for that board or a closeup picture of the board so that I could

According to you your machine's resistor burnt out. This resistor is located above the 240 volt capacitor which white base. change the resistor soon. For color code of the resistor you can follow the ... Vacuums

Bissel Proheat 2x circuit board

Use this link: http://www.4cleanerfloors.co.uk/cgi-bin/product.pl?PID=1278118_amp;brand=Bissell_amp;model=_ ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Hi, my circuit board resistors are burnt due to my re-wiring the resistor switch. How do I fix this - S3755 wiring diagram?? need to know the correct resistors or get a new board

The only way is to get a replacement board. even the dealers are not provided with that level of wiring diagrams. ... Hoover S3755 WindTunnel Bagless Canister Vacuum

Miele seb 213 Powerhead is getting ac power but there is no power to the motor. The light comes on and I get 120V on the ac side of the circuit board with a meter but zero volts on the dc side.can I replace the board or do I have to replace the whole Powerhead?

... Miele SEB 213-2 Vacuum

Wiring Two wires (black and red) connected to the slider on/off switch have overheated and melted away the 90degree connectors. Will replacing just the connectors solve the problem or is it more complicated, such as a resistor, capacitor, etc.?

This is easy and hard. If only two wires connect to the switch, cleaning up the connectors and replacing damaged items should fix it. Don't do anything unless the unit is unplugged. Try this first: connect the two wires together and tape them up. ... Electrolux EL5010A Bagged Upright Vacuum

6595-1 electrical connectors melted down

... Bissell 6595 Lift Off Bagless Upright Vacuum

Where would I find a circuit board for my Electrolux Trilobite

... Electrolux Trilobite Robotic Vacuum

Hoover Savvy U8174-900, replacement circuit board LED/Brush Motor

\015\012 \015\012 \015\012 \015\012 \015\012 ... Hoover U8171-900 / U8172-900 / U8173-900 / U8174-900 Savvy Bagless Upright Vacuum

Meile vacuum S4210 seems to have a circuit board problem

... Miele S 4210 Bagged Canister Vacuum

Acces to circuit board on dyson dc25 printer

... Dyson DC25 Vacuum

Printed Circuit board for Samsung SC8442 vacuum cleaner

... Samsung Assembly Printed Circuit Board Sub Ace - Pjt Part Dc92-00256A

I have a Hayden SuperVac 3600, almost 10 years old. The unit still runs, but now when I switch to the power nozzle, it doesn't have power to turn that. I think this happened once before and maybe they replaced a circuit board(?). We took it to a local repairman this time and he says he can fix it temporarily with a new cartridge, but that he won't promise it won't happen again soon.....

The hose has fuseable link inside, generally a 3-7 amp. It is at the wall end underneath the hose cuff. Easy to replace as it crimps in line. If you have a meter you can also test the detachable hose to wall cord for continuity, then check the hose t ... Hayden Industries SuperVac 6000 Central System Vacuum

Rewiring kenmore vac with circuit board need wiring diagram for mdl 116.22271501c

... Kenmore 23313 Whispertone Bagged Canister Vacuum

Norelco razor 6867xl - am planning to replace battery pack. Would be easier to solder if I could remove the whole circuit board system from the hard plastic case. How do you release the metal clips?

The whole circuit board is removable, and I would recommend removing it from the whole external case to work on so nothing is damaged by your soldering iron.\015\012\015\012Battery : 2x NiCd AA\015\012Battery capacity : approx. 700 ... Vacuums

Cleaner stopped working, changed bag still not working. Have checked mains fuse and liittle fuse on printed circuit board. When cleaner is on moving slider to the off positon the LED's glow red for a fraction of a second. Reset button does not feel as though it clicks when pressed, it does not seem to move. Many thanks, Hugh

... Panasonic MC-E583 Bagged Upright Vacuum

My Kenmore 116.25812508 power nozzle motor will not run unless I tilt the handle. I checked the connectivity from the circuit board in the power nozzle base to the telescoping wand with an ohm meter and there is no indication of disconnect.

I have had this vacuum for about 3 yrs and nothing but issues with it. It's been in the shop already once and it needs to go again. No power in the power head. A wheel came off of the powerhead too .. keep snapping it back on but it always comes off. ... Kenmore 25614 / 25615 Progressive Bagged Canister Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0142 seconds