Having problems with your Ridgid 25648 Wet/Dry Vacuum ?
Inside fan or impeller came apart replaced under warranty
\015 Inside fan came apart replaced under warranty last time this time it did not last very long\015
Maybe it's the brand of fan that ur using. try buying a different model
Repair Help & Product Troubleshooting for Ridgid 25648 Wet/Dry Vacuum
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
Inside fan or impeller came apart replaced under warranty
Maybe it's the brand of fan that ur using. try buying a different model ... Ridgid 25648 Wet/Dry Vacuum
How do I get the case apart on my Kirby Heritage II (2HD) to replace the fan impeller? I can only find 3 screws holding it and there seems to be more.
From the rear, there are 3 screws on right and one on the lower left. There is 1 more on the front at the top just under the lamp. You will also need to remove the safety switch - the plastic thing down and just right of the front screw. Tak ... Kirby Heritage II Vacuum
DC28 Clutch DC 28 Clutch made knocking noise after about 1 hr of use. Tried to take it apart and see it it had an obstruction but burned up the belt and damaged clutch. Yes, I know I should heave taken to the dealer or warranty service but thought it was something simple. Nothing inside is simple on a Dyson! Can the clutch be replaced and from what vendor?
... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum
Hi On a Hoover convertable model U4497-900 I'm trying to replace the fan. The old fan cracked, then flew apart. I have the new fan, have the motor assembly removed, but can't seem to get the pulley nut off the motor to replace the fan. Is there a trick to this or should I just try to muscle it? Thanks.
I replaced the impeller fan on my Kirby Classic III, it all went back together fine, but there was a leftover piece- the commutator brush cap. Where does it go? Oh, the vac isn't powering up eit
Impeller installation i took the whole vacuum cleaner apart to replace the impeller . i did not take note of the way the bushings need to be put on the shaft . do you know of a diagram out there that shows how to do this.
Here is my online guide to changing the fan. Hope it helps...\015\012\015\012http://reviews.e ... Kirby G4 Bagged Upright Vacuum
I was vacuuming and noticed that the bag needed changing. the red light with the ! inside the triangle also came on. When the bag was changed, the vacuum would not restart. The red light came on. Tried the reset button but nothing happened. Tried unplugging and re-plugging in and nothing happened. Replaced all the filters and still it wouldh't start. So I brought it downstairs and tried one more time to get it to start. it worked! Is there something wrong with the vacuum cleaner? Was it overheat
It was overheated that is why it worked downstairs after cooling off. ... Miele S548 Bagged Canister Vacuum
My hoover 600 elite is really load. I took it all apart to find the motor fan is damaged with a broken off piece which must have been vacuumed up into the bag. If I replace it sith a new plastic fan will this quiet the vacuum? right now it is tremendously loud.
... Hoover Elite U5061-900 Bagged Upright Vacuum
I have a Kirby G5 and need to replace the gear drive shaft, as the lever inside fell off and the shaft came out. (Common problem by the sound of it.) How do i remove the actual gearbox itself. I have removed the 3 screws on the bottom, but it's not coming out. What's stopping it from coming out? Do i need to remove the gearbox drive belt first? If so, how do i get to it? Thanks in advance.
HELLO, JUST USE THIS GUIDE! :0)http://reviews.ebay.com/REPLACING-OR-REPAIRING-KIRBY-VACUUM-NEUTRAL-DRIVE-PEDAL?ugi ... Kirby G5 Bagged Upright Vacuum
My floormate does not pick up liquid anymore, there seems to be no suction. I took it apart a bit to look inside and the short hose which goes from the intake area to the collecting bin is ripped and open. can this piece be replaced?
Hello,\015\012\015\012yes, the ripped part/piece can be replaced.\015\012\015\012Remove the ripped part from the device, take it to the market and use it as a sample to buy a new one. Fix it back into the device and that's all ... Hoover Floormate H3000 Upright Wet/Dry Vacuum
I have a shark steam mop and it will not get hot and steam the water so I can clean the floor. The green light works on the front and that is all that works. It there an element or something inside that heats the water. It is under warranty they should have to replace it.
Hi,Here is a tip that I wrote about the Euro-Pro Shark Steam Mop and why it maynot be getting steam to the head...Euro-Pro Shark Steam Mop Problem ... Euro-Pro Shark Steam Mop - Gray/ Purple Vacuum
My daughter pulled to hard on the ceiling fan pulling out the chain. i have taken it off and apart, nothing appears to be broken but im trying to figure out how to put it together so it retracks, i assume it has something to do with the tension of the small spring inside of it, but not sure how to put it back together im wondering if there is a internal diagram of this ???
Don't even bother to repair the pull chain switch, get a new one at KMart, HomeDepot or similar store for less than $2.\012\012Two times I've repaired one, it comes apart when I need it the most.\012\012Good Day! Don't forget to rate thi ... Vacuums
The fan broke it is falling apart can that be replace at home or does it need to go to dealer
You can do it at home. You will most likely need a t20 torx bit screwdriver. There are four screws that hold the top on and five that hold the front plate on. There is a small hole on the shaft that sticks out and is easy to stick something in there ... Kirby G4 Bagged Upright Vacuum
My powerhead on my EXL Tri-Star goes on then shuts off. When youturn it upside downit runs, then back on the floor it stops. Is it the belt inside the powerhead and if so to I take the head apart and replace this belt. Can any vacuum repair place fix this if I have the part. Vacuum was purchased in March 2000 Thank you, Dianne Miller firstname.lastname@example.org
A vac shop is probably going to require you to use their parts for warranty purposes. but its pretty simple. most shops should be capable to do it. ... Vacuums
Removing the pulley from the shaft on a hoover c1433 to replace the fan or impeller.
Removal of the pulley requires extreme care. There is a small opening on the side of the black motor housing to allow a special tool (or a screwdriver) to fit on a slot on the armature to keep it from rotating while the pulley is unscrewed. You MUS ... Hoover Commercial Guardsman C1433 Upright Vacuum
The head on my canister vac vibrates, smells and makes a bad sound. When I took it apart the inside of the "end brush tufted" piece had bits of the plastic broken off. Should I replace the Agitator Unit Assy or could this be the motor?
If you are talking about the end cap is broken off the agitator, I would replace the agitator. you can check the motor by turning on the vac without the roller installed. ... Vacuums
I am trying to replace the power cord for my 82 year old father-in-law's Oreck XL 2600HH. He already took it apart. I need to know where the semi U shaped spring steel piece is supposed to go inside the Helping Hand Handle? Any drawings or schematics available? Thank you for your time. Arthur
That justs lies on the inner handle whenb you put the spring back. There should be two holds where each end of the spring sits in. ... Oreck XL Ultra Bagged Upright Vacuum
I have a Sanitaire model SC886 upright vacuum. It's about a year old. I replaced the belt , cleaned bag , checked for blockage in impeller fan and now it makes a noise , like a grinding noise or something . Could you tell me how to fix it ?
The bearings in the motor needs to be checked,or the impeller is damage. ... Eureka SC886 Bagged Upright Vacuum
How to replace fan impeller on old Hoover upright. Taking off the belt pulley is giving me the problem.
Depends on how old it is ... if it is real old try putting a open end wrench on metal belt pully, and then hit wrench with a hammer i think counter clockwise to loosen ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum
Need to replace impeller fan on Classic III. Half the blades are broken off. I can't figure out how to remove it. I have taken cover off.
... Kirby Vacuums
The hose,essential to the vacuum, came apart. I tried tape but to no avail. Purchased 6 weeks ago. can yousend me a replacement hose? It is a Durabrand Bagless Cannister Vacuum. your phone number on the box is disconnected. It is a 1200 watt motor and I'm assuming that VCH3301 is the model number. Thanking you in advance for any assistance.Sue Jackson
I'm sorry to inform you but we're not the right place for the replacement because are a site that provides help and we're not connected to Durabrand Bagless , So for you hose replacement concern better try asking that to the store or the person whom ... Vacuums
Replace Kirby legend II fan (impeller blade) - Kirby G4 Bagged Upright Vacuum
In order to replace the fan you will buy a 2 or three piece lexan fan kit containing the fan a spacer and shaft. You must remove the carpet head and then looking from the back of the machine you will find a series of philips screws on the oute ... Kirby G4 Bagged Upright Vacuum
TOOK MY ELECTROLUX EPIC 6500 CANISTER MODEL 1762 APART TO REPLACE CORD REWINDER. TO MAKE A LONG STORY SHORT,MOST OF THE WIRES CAMES OFF OF HEIR CONNECTIONS. NOW CAN'T FIGURE OUT WHERE THEY GO WITHOUT A SCHMATIC. CAN ANYBODY HELP. THANKS CATHY
Hi,\015\012\015\012I will try to find a service manual for you. ... Vacuums
Replace fan impeller on Kirby Legend II - Vacuums
Take to repair shop u have have the tools needed to replace ... Vacuums
I took apart the power end that goes into the canister to try and get a kleenex out. in doing so i revealed the brass? rings inside also the prong part was taken out. i thought i had everything back in the way it came out but now it will not turn on. is there a reset but or something? thank you
... Panasonic MC-V9644 Bagged Canister Vacuum