Having problems with your Robot vac ?

How do you disassemble the gears

Keeps saying clean brushes and it is clean

Answers :

Repair Help & Product Troubleshooting for Robot vac

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Hi, my Roomba robot is spinning around. I cleaned it by disassembling wheels, gear compartment, etc.. Cliff sensors cleaned with compressed air. Briefly ran fine, but started to spin again. It's not under waranty anymore. Any suggestion please! Thanks, Olga

Usually this occurs when the front wheel is jammed or can't move freely, please verify if this is the case or not on your Roomba. Also, what model number of Roomba do you have? it should be located on the bottom of the unit on a label. ... iRobot Roomba 540 Vacuum

The gear that turns the dual brushes on my Bissell Spot Lifter 1716 seems to be stripped. The belt looks loose as well, but when I take the belt cover and the brush assembly out, the gear that turns the brushes is loose and appears to be stripped on the cogs. When I turn the machine on the belt turns the gear but the brushes just sit there an vibrate. They make an attempt to turn now and then but not much. Need to get a schematic or the parts so I can order the gear if it is available and th

... Bissell 1716 Spot Lifter PowerBrush Bagless Handheld Vacuum

Bissell proheat 2x 9200 series carpet cleaner. I need to remove the Brush Drive motor. However, this series has the gear end of the motor shaft poking out a hole on the left hand side. I removed the retaining washer and pin from the gear shaft. I need to get the gear off of the shaft in order to remove the motor. It's not budging. How do I remove the gear so I can pull the motor out of the unit? Thanks .

Chap, I wish someone had answered this. I'm having the exact same issue. ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

I noticed the Roomba's brushes were not sweeping, or turning so they could sweep. There was a new sound coming from the machine, the sound of grinding nylon! Upon inspection, I determined the problem to be a heat melted gear support hole. The hole was no longer round but oblong. You could see a ridge of plastic around this hole. So melting I believe was the culprit. The gear that uses that hole was then able to tilt to one side, thereby allowing the gear to disengage from the drive train. I

Be sure to keep your brush bearings clean. If they get clogged, the brushes don't turn and the drive sockets can get damaged. ... Vacuums

I need to replace the brush motor on my Bissell 9400...I can't figure out how to remove the existing motor. Took the clip off but can't get the gear off the shaft and the hole in the side isn't large enough to push the gear through...what's the secret?

... Vacuums

The little gear on the end of the brush bar motor is worn out. Where can I find a replacement gear?

... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Disassemble How do I disassemble the brush and belt assembly?

... Hoover S2220 Flair Bagless Upright Vacuum

My first proheat lasted four years so I bought a new one. After I used my Pro Heat for only the fourth time my first issue occured, the gear on the pump that runs the brushes came off, so I had the one from my old proheat, I just changed the gear spindle that is screwed to the pump and fixed that problem but now it will not pump water. That is why I bought a new proheat, I could not get the old one to pump even after a new pump and made sure all lines were not cloged.

Is your new machine a 2X or like the old style proheat? ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

Phillips Go Gear MP4 Player Model# Go Gear VIBE I need manual for this product.

Hi,\015\012Kindly let me know the complete model number of the player.\015\012You can download and print the instruction manual for Go Gear VIBE 4 GB (model SA1VBE04B) in PDF format by clicking this ... Vacuums

My Dyson DC25 animal is having issues. I believe everything is working correctly except I have realized that the mechanism which switches the hose/valve between the wand and the vacuum head isn't working properly. The two gear pieces that move the hose placement aren't close enough together, so they don't work together. It looks like there is a washer that I could potentially remove on the clear gear piece which would allow it to sit closer to the assembly. Would that work? Currently I am

... Vacuums

Varco model 534 ...rubber gear on bottom of container gear teeth are worn down so blades will not turn when put product in to be minced

... Vacuums

Saeco Odea Giro pumps the water but the internal spline or gear is not turning moving the ground coffee grinds to the point where the water can pump to the front exit lines so the water is pumped into the over flow resevoir. How do I replace the gear or check to make sure this is the problem. I want to replace this myself.. Also how do I get the unit apart it seems to be bullet proof. Is this a common problem.

It is a common problem if it is what I think it is. However your description is a little confusing. So the coffee does get ground up, but then has a hard time getting to the next stage of the process? Please clarify... And no water gets pumped th ... Vacuums

Please give directions to replace the lower shaft gear on my Pfaff 1222 sewing machine. How do I time the machine after replacing the gear?

... Vacuums

The white plastic gears are stripped --- need replacement gears

Hi,Here\012is a tip that will help you to get better results from your question\012on Fixya.\012How\012to ask a question on ... Vacuums

Thanks! Awesome tip to get into the gear box. My roomba would start up but would move very sluggishly. Looked up the beep code and it was the brushes. Brushes are cleaned regularly so it was something internal. Did your solution of getting into & cleaning the gear box and viola! He's back!

... Roomba Robotic Floor Bagless Vacuum

There is a shaft that comes out of the pump of my Bissell 1623-1 Power Steamer with gears on it. The belt to the brush attaches to it. When I went to change the belt, the belt was fine but the gear itself with the small shaft on it was no longer attached and just dropped out. It looks like there might have been a bushing there, but no more. Any ideas?

... Bissell Vacuums

Disassembling I need directions on how to disassemble.

YOU DO NOT WANT TO DISASSEMBLE THESE UNITS!! Especially if it's under warranty! They require special tools for assembly and disassembly. ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

How to disassemble electrolux ZAM 6280?i had already removed screws and don't know to disassemble it. i need to check fuse or if it needs resetting.i'm using it and it suddenly stopped completely.no power at all.

Hi There.. I had the exact same problem with my ZAM6280 model. The PCB part (location C8) had blown. Do you know the details for that part, so I can replace it? Otherwise, you didn't happen to come across any schematics for the PCB Module?? ... Vacuums

My luv300b kompressor is not synced up correctly with the gear at the base. It keeps making one round then stopping with a loud clack-clack-clack. As best I can tell is that the gear is not reversing direction. How do I sync these back up?

... LG LUV300B Bagless Upright Vacuum

My swivel sweeper 2 caught a carpet string and stripped the small plastic gear on the motor. How can I get another gear so I can repair my sweeper? Thanks, Ivol Caudill 419-243-3916 [email protected]

We were able to find every part ofr the swival sweeper exact for the gears you are looking for.\015\012You can get a new complete sweeper head for 19.99 at:\015\012 ... As Seen On TV Swivel Sweeper Vacuum

Bissell Powersteamer 1694W won't extract water from carpet. Was extracting fine until the pump/brush belt gear broke off off the pump. I repaired the gear with super glue and the brush is once again working fine. I now have an extraction problem. What did I do wrong? I took it apart and was so proud of myself when I fixed the original problem. Now I'm lost.

Check your re-assembly.\015\012\015\012Have you missed a pipe connection somewhere? ... Bissell Powersteamer 1694 Upright Vacuum

I am trying to disassemble a Eureka Mighty Mite model 3130a. I cannot get the back part at the wheels to disassemble.

... Vacuums

Car dies when u put it in gear but u can drive it but when u go to stop it will die it is a 1992 chevy camaro rs 350 throttle body with brake booster vacum un done it will sit and idle with it on it will idle for about 3 mins. but with it off it will still die when u put it in gear what do i need to do john henry sparta tnn. 38583 (931)808-3624 cell phone i have tried everything i know to do ????????

Go to autozone and buy you 2 bottles of heat and put it in the gas tank.it sounds like you have built up some condensation in you tank an its pumpimg the water thats accumulated in you gas tank.put the 2 bottles in the gas and it will dry up the wate ... Kenmore Progressive Bagless Upright with Inteli-Clean SystemVacuum

Dc17 -too much pet hair around the belt gears

I was having the same trouble and it was driving me nuts.  I tried cleaning and it did not work.  Then I tore the brush assembly off and looked up into where the little tooth gear is.  I saw something that did not look right.  The ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Where to buy the plastic gears inside turbine?

I would expect to find them at the Hoover website http://www.hoover.com/parts/ \015\012\015\012You can probably find them also at the place in your town where Hoov ... Hoover V1 SteamVac SpinScrub Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0216 seconds