Having problems with your Roomba Robotic Floor Bagless Vacuum ?

Roomba keeps saying "Clean Brushes"!!

\015 I have cleaned & cleaned this thing!It runs for about 2 mins & stops, says "Clean Brushes"!and now it's very noticeable it's not picking up well... but is picking up a bit.I take the dust bin out, and the brushes spin.... and it has much more power.... and is very clear it is working! But it's useless without the dust bin! LOLIt's only 9 months old.... called customer service, but it was the one time it worked just fine! Of course, I thought I'd stop here first before calling again!Thanks!\015

Answers :

Your ONLY solution is to remove the debris out of the gear box. When I repair these I also noticed that the gears are also damaged.
Repair Help & Product Troubleshooting for Roomba Robotic Floor Bagless Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My Irobot Roomba keeps saying that I need to clean Roombas brushes. I have cleaned the brushes...they are spotless. Still the Roomba will go for 2 minutes and shut itself off stating once again to clean the brushes. What up?


Perform the troubleshooting found at the iRobot website: http://tinyurl.com/nh5c8a (I promise that really does go to the right site.) That troubleshooting will enable you to determine exac ... iRobot Roomba 510 Bagless Vacuum

Roomba keeps saying clean brushes yet are clean!


Make sure you take off the little cap at the end (the one that spins -- just grab it and pull it straight off) and clean under it too. The rest of the brush may look perfectly clean but what happens is that hair gets stuck under spinning cap and, li ... iRobot Roomba 530 Robotic Vacuum

Roomba keeps saying clean brushes yet are clean!


Remove the Yellow connectors on the end of the brushes and clean around the pin well. If there is too much there, the roomba thinks there is something stuck and goes into clear mode (as if there is a chord stuck). ... iRobot Roomba 560 Robotic Vacuum

My Roomba 560 is making a clunking noise when it is on and it keeps stopping saying that I need to clean the brushes. I've thoroughly cleaned the brushes and I've cleaned lint from other small crevices but I'm still getting the error. Any suggestions?


I'm having the same problem with my 560 after a day of use. For me, it's caused by the little yellow spacer that's clipped onto each side of the bristly brush. When the brush assembly is closed, it wedges rather tightly next to that yellow spacer on ... iRobot Roomba 560 Robotic Vacuum

Roomba 550 keeps saying please remove and clean roomba's brushes. I have done so and keep getting error message.


Pull both brush rollers out.pull off funny looking yellow ends and clean out hair ect. ... iRobot Roomba 530 Robotic Vacuum

Roomba keeps saying "Clean Brushes"!!


Your ONLY solution is to remove the debris out of the gear box. When I repair these I also noticed that the gears are also damaged. ... Roomba Robotic Floor Bagless Vacuum

Roomba Keeps saying clean brushes, but they are clean


Is there a reset button anywhere on the device or maybe the sensor has dirt on it try that ... Vacuums

My roomba keeps telling me "error and to clean the brushes. I have cleaned the brushes and when I turn the roomba back on it keeps clicking underneath the roomba. I'm not sure what else to do.


I had the identical problem. I cleaned the brush but the problem persisted. I then put in a new brush that was provided in the box and the problem vanished. I have since used the cleaning tool on the old brush and will try and reinstall it to see ... iRobot 4150 Roomba Vacuum

My roomba 550 keeps making a clicking noise and it says to clean the brushes, even after I do it


Hello, this type of Clicking sound is most likely a loose alignment within the brush axles. There is a particular way the brushes have to go, each in an individual position. Try to tinker around with the position(s), :) lol... this should solve the ... iRobot Roomba 550 Vacuum

My Roomba stops within a few minutes of starting it and when I press the button, it says "Remove and Clean Roomba's Brushes." I have removed the brushes and cleaned them thoroughly, but within a few minutes, it stops again and says the same thing.


Hi,Accumulation of hair, dust and dirt in the Gearbox that prevents normal operation of the brushes. As a result, a power output is required to keep the brushes turning. As turning the brushes requires too much power, it con ... iRobot Roomba 4210 Bagless Robotic Vacuum

Keeps saying the brushes need cleaning - iRobot 4150 Roomba Vacuum


You will need to clean out the debris found in the gear box. Example here: http://www.imayne.co.uk/device/irobot-mod/ ... iRobot 4150 Roomba Vacuum

Keeps saying error 2 - clean brushes - iRobot Roomba 560 Robotic Vacuum


... iRobot Roomba 560 Robotic Vacuum

Brushes are clean, but Roomba stops and says clean brushes


I decided to take it apart and see if I could fix it because even if something inside went "SPROING" and I couldn't get it back together, it wouldn't be any worse than it was already. \015\012\015\012FIrst, remove the dust bin part and t ... iRobot Roomba 4210 Bagless Robotic Vacuum

My iRobot Roomba runs for 5 minutes, then it say error 2 open brushes clean brushes, which i did, then 5 minutes later it start again saying error 2 clean brushes.


... iRobot Vacuums

My Roomba runs for a while and says error 2 to clean the brushes. This happens with cleaned brushes. And I have followed the instructoins. i have got a brand new set of brushes also. When inserting them the same problem continues. The floor is clean.


Remove the two round rings.....this has worked for me like a charm since! So glad to have the Roomba back up and running! ... iRobot Roomba 560 Robotic Vacuum

My Roomba says to clean the brushes when the brushes are already clean. Is there something to take apart to check? I have already taken the brushes out. I don't know the model number, I think it's the 500 series, black and silver.


Turn the unit upside down and remove the bottom pan should be 4 or 5 screws depending on the model. next remove the 4 screws that hold the brush cartridge and pull the whole brush assembly out.using a can of compressed air cle ... Roomba 3005 Pro Robotic Vacuum

Keep getting message 'please remove and clean Roomba's brushes'. Have removed and cleaned brushes and even fitted new one's but still getting message. Also brushes sometimes rotate, sometimes not and not picking up very well at all. Help!


Must be your inbox is full, Delete old / unwanted messages. It should resolve the problem ... iRobot Roomba 500 Series Virtual Wall Lighthouse 80201 Robotic Vacuum

IRobot Roomba 560 Thumping, Says Clean Brushes, No Dirt in Cup


... iRobot Roomba 560 Robotic Vacuum

Runs for awhile then says error 2 please remove and clean roomba's brushes i do then runs for awhile and says same thing no dirt on brushes?


I had the same problem. You must clean this parts and inside this parts: Remove hair with cleaning toolRemove Roomba's brush bearingsClean Roomba's brush bearings with cleaning tool ... iRobot Roomba 560 Robotic Vacuum

I have a roomba 551. Have cleaned and removed every bit of dirt and hair off it bu the brush cage won't close when the larger bush is put in. The cage will only click locked on one side, and the other side keeps hitting the brush and won't close. It's almost as if the bursh itself is not even, but this doesn't seem to be the case either. I've even tried removing the yellow rings, but makes no difference. Occasionally it runs fine, but most of the time the roomba just hobbles and clacks as i


Hi, had the same problem, it was like the main brush no longer fit into it's slot, so the brush cage would not latch. I discovered that the yellow bearing tip on the main brush twists off, and inside I found a lot of hair twisted around the pin. Th ... Vacuums

Brushes won't fix back into holder without being forced, so Roomba clicks when it runs. It will only run a little while and then stop and say to clean Roomba's brushes.


It sounds like you didn't clean the bearings. On one end of each brush is a bearing, probably in a yellow housing. Pull the bearing off the axle, and you'll find it's full of hair underneath.Obviously, the brushes should turn freely and s ... Roomba Vacuums

Our Roomba 530 stops after few minutes saying clean the brush ,even after brushes are cleaned.


FIrst, remove the dust bin part and the brushes. Then, there are four\015\012screws on the bottom gray panel which have to be removed first in order\015\012to get to the gears which hold the brushes. I did not remove the little\015\012sweeper brush o ... iRobot Roomba 530 Robotic Vacuum

My Roomba only works correctly when I leave out the rubbery type brush (not the fiber filled brush)...... when I leave the rubber one in, it doesn't pick up & then finally stops & says REMOVED BRUSHES..... I have cleaned every nook & cranny of this thing... inside & out. I finally found that if this one brush is left off.... it works great & has for 2 weeks??? What could be the problem?


Hi,\015\012First let’s try one more time to clear out anything that might be caught inside. For this disassemble the green brush cage unit, partially, from the blue box. This would expose the cover of the gear box. On t ... iRobot Roomba 560 Robotic Vacuum

Roomba Discovery My Roomba turns on and moves but the brushes won't turn. Someone told me that I had forgotten to put in the yellow and black end bearings, but I did. Help, I miss my Roomba I have a Roomba 530, I have had it for 2 weeks and really loved it. I have followed all the cleaning instructions etc.. Then the Roomba wanted it's brushes cleaning "please clean Roombas brushes" So thinking that something was stuck I removed and cleaned the brushes, (yellow tabs on and in place by the way)


I read somewhere that you need to clear the software in case there is a glitch. To do this, take the battery out and then, simultaneously hold down the "spot" and "clean" buttons for 30 seconds. Replace battery. This has worked for my Discovery model ... Roomba Robotic Floor Bagless Vacuum

I keep getting errors on my roomba 560 telling me that I need to remove and clean the brushes. I reset it and it goes for about 2 minutes and beeps again (and the brushes look fine) What am I missing?!


Try also cleaning all the filters ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0699 seconds