Having problems with your Roomba Robotic Floor Bagless Vacuum ?

It starts and for a few seconds and then stops The battery is fine

Answers :

As Roomba 400 Series/Discovery cleans, it communicates with songs, beeps, and indicator lights. It also uses sounds to let you know when there's a problem or it needs maintenance. Here are the most common error codes, what they mean, and how to resolve the problem. If the problem cannot be resolved, click here to contact iRobot Customer Support.

Roomba beeps ...
Likely Cause / What To Do :

Plays 4-note song as Power button blinks RED
Roomba's battery is low and needs recharging Connect Roomba to a Battery Charger (or Home Base) and recharge the battery.

Roomba's Cliff Sensors are dirty or malfunctioning
Pick up Roomba and turn it over. Check for debris underneath the front bumper and around the Cliff Sensors. Wipe the Cliff Sensors with a lint-free cloth or use compressed air to clean them out.

Roomba's Side Wheel is stuck or is not touching the ground
Lift Roomba off the floor and place it in the center of the room and restart the clean cycle.

"Uh-oh" plus 1 beep
Roomba's Main Brushes stalled
Pick up Roomba and turn it over. Remove the brush guard.
Remove the Main Brushes and inspect them for any obstruction.

"Uh-oh" plus 2 beeps
Roomba's Side Brush stalled
Pick up Roomba and turn it over. Inspect the Side Brush for dirt or obstructions. Remove the Side Brush with a screw driver and check for string or hair wrapped under it. Replace the Side Brush, place Roomba in the center of the room and restart the clean cycle.

"Uh-oh" plus 3 beeps
Roomba's Vacuum stalled
Remove and empty Roomba's Dirt Bin. Use a flat-head screwdriver to remove the grill at the back of the Dirt Bin. Spin the Vacuum Impeller around, shaking out any debris that may be stuck. Replace the grill and the Dirt Bin.

"Uh-oh" plus 4 beeps
Roomba's Side Wheels stalled
Lift Roomba off the floor and place it in the center of the room and restart the clean cycle. If Roomba did not resume cleaning, lift Roomba and turn it over.* Inspect the Side Wheels for dirt or obstructions. Test the Side Wheels by pushing them in and out and making sure they rotate freely. Place Roomba in the center of the room and restart the clean cycle.

"Uh-oh" plus 5 beeps
Roomba's Cliff Sensors are obstructed
Pick up Roomba and turn it over. Check for any debris that might be caught underneath the front bumper, around the Cliff Sensors. Wipe the Cliff Sensors with a lint-free cloth or use compressed air to clean them out.

"Uh-oh" plus 6 beeps
Roomba's Wheel Drop Sensors are overloaded
Lift Roomba off the floor and place it in the center of the room and restart the clean cycle.

"Uh-oh" plus 9 beeps
Roomba's Wheel Drop Sensors have failed at startup
Please contact iRobot Customer Support.

"Uh-oh" plus 10 beeps
Roomba's bumper is not registering obstacles
Check to see that Roomba is not stuck in one place and move Roomba away from obstructions. Briskly tap the bumper on all sides several times to loosen any debris that may be lodged in it. Lift Roomba off the floor and place it in the center of the room and restart the clean cycle.

Hope this helps sure did help me just wanted to pass on good info as i came to me. Have a blessed day

Wayne W.
Is the charging ase turned on and is the dust container emptied? Any obstructions?
Repair Help & Product Troubleshooting for Roomba Robotic Floor Bagless Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

New battery!, roomba runs for 5 - 10 seconds, stops, starts running, stops, runs, stops, then beeps and low battery flashes. Have taken battery out, held start button 20 seconds, replaced battery and directly connect to charger, 72 hours min., still same problem.

... iRobot Roomba Discovery SE Bagless Robotic Vacuum

It starts and for a few seconds and then stops The battery is fine

As Roomba 400 Series/Discovery cleans, it communicates with songs, beeps, and indicator lights. It also uses sounds to let you know when there's a problem or it needs maintenance. Here are the most common error codes, what they mean, and how to resol ... Roomba Robotic Floor Bagless Vacuum

Press the power button on - good got a green light (new battery) press the clean button - got a green light iRobot runs for a couple of seconds and stops, then starts, then stops. After two or three times I now have a red light on for the Status. All of the wheels seem to be clean. I used compressed air to clean the underside. But still have the start stop problem.

How many times does the red light blink before it pauses? ... iRobot Roomba Discovery SE Bagless Robotic Vacuum

I have a Miele s251i vacuum that was working just fine until I umplugged it (while running) and re-plugged it in at a closer socket. When I replugged it, it started for a second and then stopped. Will not start now whether we use the on/off switch or not...suggestions? Would also like to know how to disassemble the unit so I could check out the wiring with a multitester..thanks

I just had exactly the same problem. Opened the vac, checked the circuit\012 next to the motor and it can be clearly seen that the Triac burned thru\012 the PCB. Will replace it and check again. Vac bought long ago, works \012extremely well. ... Miele Vacuums

My wife and I own 6 IRobots: 1 Scuba 1 Dirt Dog 4 House cleaning vacume models All of them are not working, so I decided to try and solve the problems with two of them: One is a dirt dog and the other a house cleaning vacume Rumba. Given: Battery is fully charged Reaction: I start both of them. They run for about 2 to 3 seconds They come to an abrupt stop as if there is a rock in the gears. Help

Both of them have identical issues? Can you please provide the actual part number of them? It should be on the bottom or inside the battery area somewhere.ThanksTim ... iRobot 1100 Dirt Dog Bagless Robotic Vacuum

WST 1600A I purchased this vaccum about four months ago from Heartland America. Up to this point it's worked fine. After cleaning it this time when I went to start vaccuming again it runa for about 10 seconds and cuts off. I've changed the battery, taken everything that can be removed out checked it and replaced it. THe motor sounds like it's straining. I have not taken the housing off the motor to see what's going on with that. I misplaced my manual.

It sounds like there is a clog. If there is no air flow it could be overheating. ... Westinghouse WST1600 Upright Vacuum

My irobot starts out running fine and then it will turn and slow down as if something is keeping it from going. all at once it will go full speed again. it does this until finally it stops and the red status light comes on. I just replaced the battery 6 months ago.

... iRobot 4296 Robotic Vacuum

The motor in the power head ran at a higher pitch for a for 8 to 10 seconds then stopped. If I push the reset button the powerhead may or may not start or it may start and run for a few seconds. The brush is not caught.

Did you check the belt? A broken belt results in lower strain on the motor, causing it to run faster resulting in the faster speed and higher pitch. This could result in overheating, which will cause the motor to shut off.\015\012If this isn' ... Electrolux C101 Bagged Canister Vacuum

Miele Blue moon vacuum motor surging on and off and power light flashing. After many surges of the motor (on->off->on-> off etc), the motor no longer attempting to start as ferquently ie. now off for many seconds and may turn on for 1 second.. sometimes stops turming on and just power light flashes. There is also no voltage at the plug for the hose for the power head. I noticed that the vacuum first started having probs when hair was caught in the power head and the ovetrheating light went on

... Miele Blue Moon Bagged Canister Vacuum

Roomba 4270 stops too soon. my roomba got weird all of a sudden. it started not moving all over as it should. so I tore it all down as I had done before and cleaned all the hair and dirt out of every thing I could without getting down to the basic shell. it does work now and does move all over but stops after about 10 minutes. brand new battery so not a battery issue. could I have plugged some of the sensors in the wrong 'plug'

... iRobot Roomba 560 Robotic Vacuum

I have a Howard Miller Westminster Chime Mantle Clock. It has always worked fine. It stopped working and my husband took the battery out to change it and when the new battery is in it will not work. It is Model 613-=103 movt 354201J dial 272142J. The part you put the battery in almost looks too big for one double A but I can't see how two would fit. I am afraid the battery is just not in right. Can you help me with how many batteries go in this clock or if it is one what the problem could be.

... Vacuums

Problem starting Sometimes will not start at all. Sometimes will do a quick start and stop. Other times it starts and runs fine????

This can happen if you have an intermittent short in your cord. Try plugging it in and then wiggling the cord around where it goes into the body of the vacuum with the switch set to "on." (If you're not sure whether it's on or off, just click it back ... Dyson DC07 Bagless Upright Cyclonic Vacuum

I have a dyson canniter stow away vacuum. i've had it for 2 years and it just started having a problem. when i turn it on the motor starts just fine but the vacuum head does not turn on. Yet when i push it forward it trys to start and turns on for a second and turn off - almost like the connector isn't connecting the hose to the head very well anymore.

Hi, After reading you're problem, the symptom's are just like you said. Its just a matter of checking the connections. The connection where it plugs into the head it self. When you push forward the forward motion and down pressure makes ... Dyson "Stowaway" Canister Vacuum Vacuum

Good evening, I have a Xio Z1010 electrolux vaacum cleaner and I hope you'll be able to give me some advice. The vacuum cannot be started. Last time it started for a few seconds and stopped suddenly. Something similar happened long time ago but that was due to overheating. Once cooled down in few hours it would start again. It is not the case now after 24 hours. Could you give me any idea what could be the reason? Your help would be much appreciated. Adorian

... Electrolux Vacuums

Shark Euro-pro EP621 Bagless Upright Vacuum. Q regarding the brush not spinning / after troubleshooting and taking actions listed below, it now spinning for a few secs, but then stopping. Already removed hair, strings, etc. Checked that belt is aligned properly, checked that small wheel that turns belt is working (spins fine when belt removed. Oiled the turning parts a bit, that made it spin better, but still stops. It turns about 3-4 seconds then stops. If I switch it off and on again, I get ag

... Euro-Pro EP621 Bagless Upright Vacuum

Roomba Red 4100 goes for 5 seconds then stops

... iRobot Roomba Red 4100 Bagless Robotic Vacuum

Err5 When charging the battery, it starts out flashing amber, but after several minutes it turns red and the err button flashes five times. The troubleshooting says to hold the buttons above and below the power button for ten seconds and this may resolve some software issues. I tried that but it goes back to the amber light then red again. I replaced the battery hoping that was the issue, but it still does the same thing.

... iRobot Roomba 530 Robotic Vacuum

My shark steamer has stopped working after a year of having it (I have already replaced one, I'm a idiot!). My problem; however, is that it will steam, but the steam stops traveling through the actual "mop" part. I plugged it in, wait seconds and start pumping, but the steam builds up until it's hard to pump. I had to press the button really hard for the bottom to come off and it shot off like a rocket! I tried to stick something through the tubing, but it did nothing. What am I doing wrong? I

\012\012\012Hi,Here\012is a tip that I wrote about the Euro-Pro Shark Steam Mop and why it\012may not be getting steam to the head... ... Euro-Pro Shark Steam Mop - Gray/ Purple Vacuum

When i start the vacum the brushes trun for about 3-5 seconds then stops. the vacum still runs,its just the brushes stop turning, what should i do?

If your machine has no power or interrupted power, please check the following:\012 \012- Make sure the power cord is plugged into a functioning outlet to check for power.- The handle may not be installed properly, causing a ... Bissell Healthy Home HEPA Bagless Upright Vacuum - Metallic Blue

Infinity Vaccum by Shark, model number NV31COS, will not start. The vacuum was running just fine until it grabbed the edge of a curtain. Turned it off to release the suction. Turned it back on and was working fine. About a minute later the vacuum was making an odd noise. Every 2 seconds or so it would "heave" (lack of a better word) then go away, then come back and so on. Turned the vacuum off and checked for blockage, none that could be seen or felt, and now the vacuum won't turn. Any suggestio

Carpet brush won't turn when vac on ... Euro-Pro NV31 Infinity Vacuum


Sounds like it overheats quickly. But why are you not able to return it? ... Hoover U5750-900 WindTunnel Bagless Upright Vacuum

Panasonic canaster vacumn cleaner model MC-9647C only runs a few seconds and shuts off, after a rest starts then stops after a few seconds. I changed bags and cleaned the filter...any suggestions? Thanks, Phil

... Panasonic Vacuums

Hi. I have Dyson dc08 hepq+. Thet problem is its not having suction .I checked inside the pipe and foot , ery thing is fine. And if i take the whole dirtbin out ...machine workes fine. when i put ery thing back ....as soon as i start it , after 2 second machine change its voice...and loos suction. I think its just happen because ...the saftey yellow valve inside the machine turns up because the dirt drum is blocked inside some where. Any suggstion ...what can i do with it. I m tahnkful in avance

Hi its Darran at Dyson.From your description of the problem, it sounds as though the bin inner is missing. To confirm this, if you remove the cyclone and bin from the machine, then separate the 2 pieces as if you were going to empty it, w ... Dyson DC08 Hepa Allergy Bagless Canister Cyclonic Vacuum

My purple Dyson Animal (without the ball) isn't working correctly. When I turn it on, the red power light, as well as the medium pile buttons flashes. When I first turn it on, the brush rotates for 3 to 5 seconds, then once I start moving the vacuum, it stops and that's when the lights start flashing. I've checked the filters, they are dry and installed correctly. What could be the problem?

I need help repairing my Dyson. I cannot push the buttons down to select Short pile/Medium pile or bare floor. The buttons will not push down at all. It will not allow me to select anything. I have very short pile carpet so it does not pick up that w ... Dyson DC28 Animal Bagless Upright Vacuum

Dyson 28 animal. When I start the vacuum the roller spins for a couple of seconds the stops. I have to turn machine off and on again then the roller will work for another couple of seconds.

... Dyson DC28 Animal Bagless Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0424 seconds