Having problems with your Roomba Robotic Floor Bagless Vacuum ?

When it goes onto the rug it says to clean I do and it runs a few minutes and says it again. It never quits on the linoleum


Answers :

If the sensors become obstructed by dust or debris the infrared signal is weakened. Regularly inspect and clean the sensors and use compressed air for better results
On all vacumn cleaners their is a control for the suction required between carpets and lino ,this is normally a flap on the suction side to allow more air in to it doesnt stick and overload the motor ,have a look underneath the machine and see it has a similar device somewhere or look in the operating manual
Repair Help & Product Troubleshooting for Roomba Robotic Floor Bagless Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

When it goes onto the rug it says to clean I do and it runs a few minutes and says it again. It never quits on the linoleum


If the sensors become obstructed by dust or debris the infrared signal is weakened. Regularly inspect and clean the sensors and use compressed air for better results ... Roomba Robotic Floor Bagless Vacuum

My iRobot Roomba runs for 5 minutes, then it say error 2 open brushes clean brushes, which i did, then 5 minutes later it start again saying error 2 clean brushes.


... iRobot Vacuums

Dyson dc7 quits after a few minutes running; runs again after an hour or two of rest. Filters are clean, beater bar is clean, can't tell about the airways because I can't see how to get to them.


Check the ducts with a small object(screw or something with a little weight)down the ducts to verify they are clean. Also check the Ubend on the back bottom of the unit. Looks just like a U. Remove with a turn of the tab by a screwdriver or quarter ... Vacuums

I HAD MY DC17 VAC FOR 3 YRS NOW NO PROBLEMS AT ALL, I REGULARLY CLEAN THE FILTER LIKE IT SAYS BUT LATELY I'VE NOTICE THAT THERE SEEMS TO BE A LOT MORE COLLECTION ON THE TOP OF THE FILTER WHEN I'M DONE VACUUMING. IT HAS ALSO STARTED THIS WEEK TO MAKE A VERY LOUD HUMMING TYPE NOISE WHILE RUNNING, I HAVE CHECKED FOR ALL POINTS FOR ANY BLOCK AND NOTHING AND NOW TODAY IT RUN A FEW MINUTES AND STOPS AUTOMATICALLY,IT WILL RESTART AFTER I LET IT SIT UNPLUGGED.WHATS UP WITH THIS THING, IT HAS BEEN GR


The vac is over heating. First, you should try a new filter. Also, keep in mind that after cleaning the filter, make sure that it fully dries. Using a wet or damp filter clogs it quickly. Second, turn the vac upside down and make sure that the roller ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Makes clicking noise and runs for a couple of minutes and then says error 2 open roomba and clean brush cage-do that and the same thing happens 2 minutes later


Pet hair often gets sucked into the gear box that drives the brushes and can clog it enough to generate this error. \015\012you need to remove the CHM (cleaning head module) and open the gear box on it to clean it out... you can also visit iRobots ... iRobot Roomba 560 Robotic Vacuum

Keeps stopping. My Roomba Discovery says it has a full charge, but it runs for a few minutes, then stops and beeps and the status light comes on. If you press the clean button, it will start again and go for a few minutes before the same thing happens again.


Your battery isn't holding a charge ,buy a new battery ... iRobot Roomba Discovery SE Bagless Robotic Vacuum

Why does our Roomba says there is a problem with the brushes even after they have been thoroughly cleaned? It will run a minute maybe then tell us there is a problem, check brushes.


You need a new battery if you have done the battery reset,and then leave the unit on the charger for 16 hours straight if the problem continues after the charge you need to get a new battery ... Vacuums

My iRobot Roomba runs for about ten minutes, then shuts off. I can keep pushing the clean button and it will run for another ten minutes and stop again. Nothing seems to get clean.


Take the brush rolls out and you should see a copper disc. It is the dirt sensor. Clean it with Windex or some other cleaner. This works sometimes. ... iRobot Roomba 550 Vacuum

My Roomba stops within a few minutes of starting it and when I press the button, it says "Remove and Clean Roomba's Brushes." I have removed the brushes and cleaned them thoroughly, but within a few minutes, it stops again and says the same thing.


Hi,Accumulation of hair, dust and dirt in the Gearbox that prevents normal operation of the brushes. As a result, a power output is required to keep the brushes turning. As turning the brushes requires too much power, it con ... iRobot Roomba 4210 Bagless Robotic Vacuum

Our miele red star(s314i) vacuum was running great and quit suddenly. It had not been running for a very long time and just quit. Newish bag, no clogs in hose and doesn't seem overly hot. the over heated warning light did not come on. I've waited 30 plus minutes to try to restart and no luck. Any ideas


Ok, so if the cord test didn't fix the problem, then it sounds like either the plug has gone bad, or the switch. The plug is a very common problem to go bad, and can be caused by just simply yanking the plug out of the wall, or putting too much tens ... Miele Red Star Bagged Canister Vacuum

Attachment problem used a new unit w/attachment for 5 minutes...dispensed solution in a powerful triangular fashion. Then the fluid quit dispensing out of the attachment nozle amost like the pump quit working. Primed the unit several times w/ no success. checked for clogs. can't tell if the floor portion is "pumping' or just dribbling solution onto the floor with the trigger. can see no leaks at this point. unit worked for about 5 minutes on apholstery


Make sure everything is filled and secured tightly, if this a new unit it should be something simple ok, also check where machine folds down that the solution hose is not being pinched its right behind the dirty water tank ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Runs for awhile then says error 2 please remove and clean roomba's brushes i do then runs for awhile and says same thing no dirt on brushes?


I had the same problem. You must clean this parts and inside this parts: Remove hair with cleaning toolRemove Roomba's brush bearingsClean Roomba's brush bearings with cleaning tool ... iRobot Roomba 560 Robotic Vacuum

I have a nearly 9 year old Electrolux Excellio Z5228 vacuum cleaner. It has recently started cutting out during operation. I cleaned the micro filter (between bag & motor) via brush & hitting against wall & seems / looks quite clean. I washed the gore filter (output from motor to clean the exhaust air) as per instructions, then let to dry. It was very clogged but now very clean. The vacuum clearner still cuts out often. Even after a long rest (say overnight) it still won't start, then ano


... Electrolux Vacuums

My Irobot Roomba keeps saying that I need to clean Roombas brushes. I have cleaned the brushes...they are spotless. Still the Roomba will go for 2 minutes and shut itself off stating once again to clean the brushes. What up?


Perform the troubleshooting found at the iRobot website: http://tinyurl.com/nh5c8a (I promise that really does go to the right site.) That troubleshooting will enable you to determine exac ... iRobot Roomba 510 Bagless Vacuum

Brushes only work when Dust Bin is removed!! I have cleaned & cleaned this thing! It runs for about 2 mins & stops, says "Clean Brushes"! and now it's very noticeable it's not picking up well... but is picking up a bit. I take the dust bin out, and the brushes spin.... and it has much more power.... and is very clear it is working! But it's useless without the dust bin! LOL It's only 9 months old.... called customer service, but it was the one time it worked just fine! Of course, I thought I'


HI, If the brushes work , without the bin, the problem , the problem could be caused , due the failure at the bin lock mechanism. There is a sensor that checks if the BIN is connected properly or not. This problem is best resolved by getting ... iRobot Roomba 560 Robotic Vacuum

I have cleaned & cleaned this thing! It runs for about 2 mins & stops, says "Clean Brushes"! and now it's very noticeable it's not picking up well... but is picking up a bit. I take the dust bin out, and the brushes spin.... and it has much more power.... and is very clear it is working! But it's useless without the dust bin! LOL It's only 9 months old.... called customer service, but it was the one time it worked just fine! Of course, I thought I'd stop here first before calling again! Than


Ok, this is a "Brush Height Adjustment" issue. It will probably work great on a hard surface but on carpet the brushes bog. If you've taken the unit apart already...Sorry....do it again. When you do, you'll see a String which allows the brushes to " ... iRobot Roomba 560 Robotic Vacuum

Ok. i have a bissell proheat 2x model # 8920 06356c i'm trying to clean a large rug in my home .. i have the fluid in the tank and can't figure out why it's not cleaning as it should.. the motor's running but not spraying and cleaning as i expected to do..


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 8910 ProHeat Clear View Upright Vacuum

Isn't picking up lint. Will pick up other things like flecks of paper but will not get any fuzz or fibrous material off any rug no matter what the setting. This is a recent problem. Have owned the vacuum for awhile and never seen this issue before. Is it an easy fix? I've cleaned the brush, cleaned out the filters, cleaned the dirt tank. Nothing changed.


Is the brush turning on the bottom of the machine ? If not It could be clogedup with stuff or the belt could be worn on it and it will turn but as soon as it contacts the floor it will stop turning. The belt is easy to replace by removing screw ... Bissell 3576 CleanView II Bagless Upright Vacuum

My Roomba runs for a while and says error 2 to clean the brushes. This happens with cleaned brushes. And I have followed the instructoins. i have got a brand new set of brushes also. When inserting them the same problem continues. The floor is clean.


Remove the two round rings.....this has worked for me like a charm since! So glad to have the Roomba back up and running! ... iRobot Roomba 560 Robotic Vacuum

I have had my Bissell 6591-X for 2 years. I hate it! No matter what I do all the fuzz, hair, whatever fills up around the upper filter before it even starts to deposit in the cup. It has done this ever since I bought it. No matter how much I take it apart, clean it, clean filters, empty the cup, nothing does any good. I spill more dirt onto the vacuum and floor than ever gets in the cup. I will never buy another Bissell.


Sure your not over filling it ? ... Bissell Vacuums

After running for 15 minutes, the windtunnel vacuum cleaner shuts off. It will not restart until it has been off for 30 minutes. Could it be overheating for some reason. All of the filters are clean; the dust tank is empty; the belts have no cracks.


It's not necessarily overheating, but the thermal-fuse is definitely tripping and it takes 30 minutes to reset. There are several causes of this (in most common order):\015\012\015\0121. A blockage in the suction system or a full dust tan ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

My Kenmore Quick Clean vac clogs at the top of cannister and does not let dirt to go to canister. After vacuum for few minutes have to stop empty before continuing to get rug clean. Is there anything that I can do to solve problem.


You need to own an air compressor,and blow out all vacuums ,after each use. ... Kenmore Vacuums

Irobot run then shuts down-says check brushes-brushes clean-also when running does not pick up hair, and such on carpet.


Has a internal short. ... Vacuums

Dyson Quits My Dyson quits after running a few minutes. Than starts back up after a bit.


Cut out switch on the motor needs replacing this overheats and cuts of the motor when the motor cools down it will start again you have to keep both filters and cyclone clean and free of dust or after replacement the same will happen again ... Dyson DC07 Bagless Upright Cyclonic Vacuum

When I was putting my new rug shampooer together and the directions said to press the trigger and the clean surge button until I heard a snap, I did just that many times and never did hear a snap so I thought it had likely happened and I didn't hear it so I proceeded to fill the solution tank and get busy but no solution came out so I used the clean surge button instead and got the job done (I think). Can I continue to use it that way or is there a way I can get it to snap and use it the way it


My husband figured it out and it now works great! Thank you ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0800 seconds